Hyundai H-1550 Instruction Manual

H-1550

RADIO WITH ALARM

РАДИОПРИЕМНИК

С БУДИЛЬНИКОМ

Руководство по эксплуатации Instruction manual

Instruction manual

Dear customer!

Thank you for purchasing our product. For safety, it is strongly recommended to read this manual carefully before connecting, operating and/or adjusting the product and keep the manual for reference in future.

Description

Rear panel

1 2 3 4 5 6 7 8

9 10 11 12 13 14 9

1. SNOOZE button

2. Function switch

3. ALARM.SET/MEM-DN button

/TUN- button

5. /MEMO/USB/SD button

6. /TUN+ button

7. TIME SET/MEM-UP/12H/24H button

8. USB port

9. Speakers

10. LINE IN jack

11. Memory card slot

12. VOLUME regulator

13. DC IN 5V power input

14. FM antenna

Not indicated: battery compartment (bottom

panel), additional battery terminal (bottom panel), LED display (front panel)

Instruction manual

Remote controller

/PLAY/PAUSE button

2. /TUNING button

3. USB/SD button

4. CLOCK button

5. SNOOZE button

6. Number buttons

7. /TUNING button

8. MUTE button

9. REPEAT button

10. ALARM button

11. MEMORY button

9 10 11

Utilization of the product

If you want to dispose this product, do not mix it with general household waste. There is a separate collection system for used electronic products in accordance with legislation that requires proper treatment, recovery and recycling.

Please contact your local authorities for the correct method of disposal. By doing so, you will ensure that your disposed product undergoes the necessary treatment, recovery

and recycling and thus prevent potential negative effects on the environment and human health.

Important safeguards

• The instruction manual contains important operating and maintenance instructions. For your safety, it is necessary to refer the manual. Keep the manual for use in future.

• Do not hit or drop the unit.

• Do not expose the unit to vibration, direct sunlight, too high or low temperature or humidity.

• If you are not going to use the unit within a long period of time, remove the batteries to avoid their leakage.

• Do not disassemble the unit yourselves. Refer servicing to qualified service personnel.

Power supply

Battery operation

• Open the battery compartment cover. Insert 4 x AAA batteries (not included). Please observe correct battery polarities or the unit will not work. Close the battery compartment cover.

• When the batteries are exhausted, they should be replaced.

• Do not use new and old batteries together. Do not recharge or heat the batteries. Uncharged batteries are not a reason for addressing to a repair service.

• Disconnect power cord from the socket, when the unit is on battery supply. Battery power is automatically disconnected when the power cord is connected to a power socket.

AC adaptor power

• Plug the supplied AC/DC power adaptor into the power input on the back of the unit. Connect the power cord to the AC household main outlet. Make sure the voltage is compatible.

• Always remember to disconnect the

Instruction manual

power cord from the main supply before disconnecting it from the unit.

• Disconnect the power cord from the mains

when not in use.

Additional power

• Insert 2 batteries AG13 into the additional battery terminal. This is additional power supply intended for maintenance of clock and alarm settings. Without the additional power you will need to set the clock and alarm anew after each interruption of power supply.

• When the batteries are exhausted they should be replaced. New batteries should be aquired by user. Replace the batteries only with batteries of the same type.

Setting the clock

Set the function switch to MODE position. Press and hold CLOCK button on the RC (TIME SET/MEM-UP/12H/24H button on the unit) until the digits flash. Press repeatedly /TUN- and /TUN+ buttons on the unit ( / TUNING and /TUNING buttons on the RC) to set 12-hour or 24-hour clock display mode. Press CLOCK (TIME SET/MEM-UP/12H/24H) button to go to hour setting, hour digits will flash. Press repeatedly /TUN- and / TUN+ ( /TUNING and /TUNING) buttons to set hours. Press CLOCK (TIME SET/MEMUP/12H/24H) button to go to minute setting, minute digits will flash. Press repeatedly /TUN- and /TUN+ ( /TUNING and /TUNING) buttons to set minutes. Press CLOCK (TIME SET/MEM-UP/12H/24H) button to confirm clock setting.

buttons on the unit ( /TUNING and / TUNING buttons on the RC) to change the current frequency downwards or upwards by 100 KHz.

• Press and hold /TUN- and /TUN+ ( /TUNING and /TUNING) buttons to search the nearest strong signal station downwards or upwards automatically.

• Press MEMORY button on the RC ( /MEMO/USB/SD button on the unit); C01 will blink. Press repeatedly TIME SET/MEMUP/12H/24H or ALARM.SET/MEM-DN buttons on the unit to select the position number for the current frequency. Press MEMORY ( /MEMO/ USB/SD) button to save the frequency in the position (1~30).

• Press and hold MEMORY ( /MEMO/ USB/SD) button; it will start scanning from the lowest frequency and automatically save all available stations in positions (up to 30).

• When stations are saved in the memory, press repeatedly TIME SET/MEM-UP/12H/24H or ALARM.SET/MEM-DN buttons on the unit or number buttons on the RC to select saved stations.

• In radio mode, press SNOOZE button; the display will show the current frequency for 10 seconds, then return to clock.

• Rotate VOLUME regulator to adjust the sound volume level. Press MUTE button on the RC to switch off the sound; the digits on the display will blink. Press MUTE button again to enable the sound.

• Extend the FM antenna for a better signal reception.

Alarm operation

Radio operation

• Set the function switch to RADIO position; the current radio frequency will be displayed for several seconds, then clock will be displayed.

• Press repeatedly /TUN- and /TUN+

Setting the alarm

• Set the function switch to MODE position.

• Press and hold ALARM button on the RC (ALARM.SET/MEM-DN button on the unit) until the digits flash. AL1 indicator will be blinking showing that the 1st alarm is being set.

• Press repeatedly

/TUN- and /TUN+

Instruction manual

buttons on the unit ( /TUNING and / TUNING buttons on the RC) to set hours of the 1st alarm (AL1). Press ALARM (ALARM. SET/MEM-DN) button to save hours; minute digits will flash. Press repeatedly

/TUN+ ( /TUNING and /TUNING) buttons to set hours of the 1st alarm. Press ALARM (ALARM.SET/MEM-DN) button to save minutes; the unit is in the signal sound selection mode. Press repeatedly and

/TUN+ ( /TUNING and /TUNING) buttons to set USB/SD (USB and SD indicators blinks), radio (FM indicator blinks) or buzzer (no indicator blinks) as the sound signal of the 1st alarm.

• Press ALARM (ALARM.SET/MEM-DN) button to save the settings of the 1st alarm. AL2 indicator will be blinking showing that the 2st alarm is being set.

• Press repeatedly buttons on the unit ( TUNING buttons on the RC) to set hours of the 2nd alarm (AL2). Press ALARM button (ALARM.SET/MEM-DN button) to save hours; minute digits will flash. Press repeatedly /TUN- and /TUN+ ( /TUNING and /TUNING) buttons to set hours of the 2nd alarm. Press ALARM (ALARM.SET/MEM-DN) button to save minutes; the unit is in the signal sound selection mode. Press repeatedly /TUN- and /TUN+ ( /TUNING and / TUNING) buttons to set USB/SD (USB and SD indicators blinks), radio (FM indicator blinks) or buzzer (no indicator blinks) as the sound signal of the 2nd alarm.

• Press ALARM button (ALARM.SET/MEMDN button) to save the settings of the 2nd alarm.

/TUN- and /TUN+

/TUNING and /

/TUN- and

/TUN-

General operations

• In any mode, press repeatedly ALARM button (ALARM.SET/MEM-DN button) to check settings of 1st and 2nd alarms.

• Ensure that the function switch is in MODE position and AL1 and AL2 indicators are on, otherwise the alarm will not work. To switch off the alarm mode, press and hold SNOOZE button; AL1 and AL2 indicators will be off.

Repeat the operatios again to switch on the alarm mode.

• Do not select USB/SD as alarm signal if USB or memory card is not connected, otherwise the alarm will not work.

• If you want to select radio as alarm signal, switch to the needed station first.

Snooze control

• When the alarm is on, press SNOOZE button once, after 9 minutes the alarm will be on again. This operation can be repeated several times.

• When the alarm is on, press ALARM button (ALARM.SET/MEM-DN button) or set the function switch to another position to stop the alarm.

• When the alarm is on, if you don’t press ALARM button (ALARM.SET/MEM-DN button), it will stop after 90 minutes.

USB/SD operation

Playback

• Insert a USB device into the USB port. Insert an SD memory card into the memory card slot according to the marking on the unit.

• Set the function switch to USB/SD position. Playback of the first track contained in the USB/memory card will start automatically. If both USB and SD are connected simultaneously, USB will be played by default. If you connect an SD card while USB is being played, the unit will switch to SD card playback. Press USB/SD button on the RC or press and hold /MEMO/USB/SD button on the unit to switch between USB and SD playback. When USB is being played, USB indicator flashes; when SD is being played, SD indicator flashes.

• The display starts by showing the number of the first track for 10 seconds, then the display shows clock. Press SNOOZE button to switch between track number and clock display.

• Press /MEMO/USB/SD button on the unit ( /PLAY/PAUSE button on the RC) to pause

+ 10 hidden pages