Hyundai H-1433 Instruction Manual

КАССЕТНАЯ CD/MP3/USB/SD-

СТЕРЕОМАГНИТОЛА

PORTABLE STEREO RADIO

CASSETTE RECORDER WITH

CD/MP3/USB/SD

Руководство по эксплуатации Instruction manual

H-1433

2 3

Instruction manual Instruction manual

Dear customer!

Thank you for purchasing our product. For safety, it is strongly recommended to read

this manual carefully before connecting, operating and/or adjusting the product and keep

the manual for reference in future.

Description

1. button (cassette pause)

button (cassette stop/eject)

button (cassette fast forward)

button (cassette rewind)

button (cassette play)

button (cassette record)

7. FUNCTION switch

8. Handle

9. Memory card slot

10. USB slot

11. CD compartment handle

12. REPEAT/PROG button

13. SKIP+10/FOLDER button

14. TUNING knob

15. Band (AM/FM/FM ST) switch

16. DBBS switch

17. VOLUME knob

18. PLAY/PAUSE button

19. NEXT button

20. STOP/CD/USB/SD button

21. LCD display

22. BACK button

Not indicated:

Back of the unit: Headphone socket, Power

cord socket, Telescopic FM antenna

Bottom of the unit: Battery compartment.

1 2 3 4 5 6 7

20 21 22

Stereo headphone connection

• For private listening, insert 3.5 mm

headphone into the stereo headphone jack (on

the back side of the unit).

• Adjust volume control to the appropriate

level as desired by turning VOLUME regulator.

• When the stereo headphone jack

is plugged, speakers will disconnect

automatically.

Radio operation

• Set FUNCTION switch to RADIO position.

• Select your desired broadcasting band

with BAND switch.

• Rotate TUNING knob to receive the

desired broadcast.

• Adjust the level of sound with VOLUME

knob.

• To turn off the radio, set FUNCTION

switch to TAPE position.

Antenna

• For FM reception, adjust the telescopic

antenna appropriately to obtain the best

reception on the band selected.

• The AM signal is picked up through the

built-in ferrite antenna. The set should be

placed to a position for the best reception.

FM and FM stereo reception

• Set BAND switch to FM position,

programmer is received in mono mode.

In particular when stereo signal is weak

and much noise are received, it is preferable to

receive stations in mono.

• Set BAND switch to FM ST position,

programmer is received in stereo mode, thus

FM STEREO indicator should light up.

Important safeguards

• Attention: The owner’s manual contains

important operating and maintenance

instructions. For your safety, it is necessary to

refer to the manual.

• Dangerous voltage: Uninsulated

dangerous voltage that may be of sufficient

magnitude to constitute a risk of electrical

shock to persons is present within this product

enclosure.

• Caution: To reduce the risk of electric

shock, do not dismantle the body. Prefer

servicing to qualified service personnel. Do not

use the unit in places where it can be exposed

to water, moisture and dust. Make sure that

pins or other foreign objects do not get inside

the unit; they may cause malfunctions, or

create safety hazards such as electrical shock.

Power supply

Battery operation

• Open the battery compartment cover.

• Insert 6 batteries (UM-2). Please observe

correct battery polarities or the set will not

work.

• Close the battery compartment cover.

AC operation

• Before the first connecting of the appliance

check that voltage indicated on the rating label

corresponds the mains voltage in your home.

• Insert the plug into power supply.

Caution:

• When the set is only used with AC or is

not used for 2 weeks or more, please remove

the batteries, to avoid damage to the set from

leakage of batteries.

• Always switch off the unit when not in use.

• Always unplug the appliance from power

supply, when not in use long time.

Instruction manual

CD/MP3 operation

Insertion and removal of discs

• Place a disc into the compartment with the

label-side (printed side of disc) facing upwards.

Press down in the center part of disc until the

disc “locks” onto the center spindle.

• When the disc has been placed onto

the center spindle, gently lower the CD-door

downwards until it locks shut. The disc is now

ready to be played.

• Press STOP/CD/USB/SD button to stop

the disc spinning before opening the CD-door.

• To remove a disc, follow the same

procedure as described above, except to

remove the disc instead of inserting it into the

compartment, by placing one finger at the

middle of disc (center spindle) and the other at

the edge of the disc and gently pulling upwards.

Always hold a disc by its edges. Avoid

getting any fingerprints, smudges or dirt onto

the surface of a disc. In case this happens, use

a special CD-cleaning cloth or cleaning kit to

remove the dirt or smudges. Please make sure

to always fold down the handle before opening

the CD door.

General operation

• Set FUNCTION switch to CD (MP3)

position.

• Put a disc into the CD compartment and

close the CD door.

• The LCD display will show the total

number of tracks after a few second.

Play/pause mode

• Press PLAY/PAUSE button to start play,

the LCD display will show the first track and

PLAY icon.

• Press PLAY/PAUSE button to pause at

any track when playing, PLAY icon on the

display flashes.

• To stop the disc, press STOP/CD/USB/SD

button.

• If the disc contains folders with files,

select a folder by pressing SKIP+10/FOLDER

button. Also, press this button to skip 10 tracks

forward.

Skip and search mode

• Press NEXT button once to skip to the

next track.

• Press BACK button once to skip back to

previous track.

• Press and hold BACK and NEXT buttons

to start fast backward or forward playback until

you find the passage to play from.

Repeat mode

• Press REPEAT/PROG button once for

single track repeat playing.

• Press REPEAT/PROG button twice for all

tracks repeat playing.

• To cancel repeat play, press REPEAT/

PROG button once again.

Program mode

• Up to 20 tracks can be programmed for

disc play in any order or the same track can be

repeated up to 20 times. Before use, be sure to

press STOP button.

• Press REPEAT/PROG button, the memory

position number will show on the display.

• Select a desired track by using BACK and

NEXT buttons.

• Press REPEAT/PROG button to confirm.

• Repeat the two last steps as described

above to enter additional memories into the

program if necessary.

• When all the desired tracks have been

programmed, press PLAY/PAUSE button

to play the disc in the order you have

programmed.

• To stop the CD, press STOP/CD/USB/SD

button.

The program memory will be cleared

only when the CD compartment is opened or

turn off the CD or power supply.

• To turn off the CD player set FUNCTION

switch to TAPE (OFF) position.

Good quality sound is guaranteed only

when playing licensed discs.

+ 9 hidden pages