Hyundai H-1419, H-1419 New User Manual [ru]

H-1419

Cтерео магнитола с CD/MP3/USB/SD Инструкция по эксплуатации

CD/MP3/USB/SD radio player Instruction manual

Description

Unit description

1. CD door

2. IR sensor

3. CD door finger grip

4. LCD display

5. Handle

6. PLAY/ PAUSE key

7. BACK /TUNE DOWN key

8. CD key

9. Speakers

10. NEXT /TUNE UP key

11. MEM/PROG/P-MODE key

12. STOP key

13. BAND key

14. ON/OFF key

15. USB/SD key

16. SLEEP key

17. EQ key

18. FOLDER/FM-MODE (FM mono/stereo) key

19. USB drive socket

20. SD card socket

21. +10/MEM + / -10/MEM- keys

22. VOL. UP / VOL. DN keys

Back of the unit: Telescopic antenna, Mains socket AC 220V~ 50 Hz.

Bottom of the unit: Battery compartment.

Remote control description

1. VOLUME +/– keys

2. POWER key

3. STOP key

4. PLAY/PAUSE key

5. BASS key

6. EQ key

7. SLEEP key

8. FOLDER/FM-MODE (FM mono/stereo) key

9. -10/ MEM – / +10/ MEM + keys

10. USB key

11. MUTE key

12. BACK /TUNE DOWN / NEXT /TUNE UP keys

13. PLAY MODE key

14. CD key

15. PROG. key

16. RADIO/BAND key

17. SD key

Note: all the buttons functions are same as for the unit buttons.

Important safeguards

• ATTENTION: The owner’s manual contains important operating and maintenance instructions. For your safety, it is necessary to refer to the manual.

• DANGEROUS VOLTAGE: Uninsulated dangerous voltage that may be of sufficient magnitude to constitute a risk of electrical shock to persons is

present within this product enclosure.

• CAUTION: To reduce the risk of electric shock, do not remove cover (or back). Prefer servicing to qualified service personnel.

Power supply

Battery operation

• Open the battery compartment cover

• Insert 6 batteries (UM-2/LR14). Please observe correct battery polarities or the set will not work.

• Close the battery compartment cover.

AC operation

• Before the first connecting of the appliance check that voltage indicated on the rating label corresponds the mains voltage in your home.

• The AC cord is located inside the battery compartment. Connect it to the unit.

• Insert the plug into power supply.

CAUTION:

• When the set is only used with AC or is not used for 4 weeks or more, please remove the batteries, to avoid damage to the set from leakage of batteries.

• Always switch off the unit when not in use.

• Always unplug the appliance from power supply, when no use long time.

Radio operations

• Press ON/OFF key once to switch on the system power.

• Press BAND key repeatedly to select the radio mode and the desired radio band: AM or FM

• Press NEXT/TUNE-UP button or BACK/TUNE-UP button and then release the button when the fast scanning starts. The frequency will continue to

change and will automatically stop when a broadcast station is received.

• To receive a weak broadcast signal press the NEXT/TUNE-UP or BACK/TUNE-DOWN button by one press at a time and adjust the frequency you wish to receive.

Saving stations to memory

• 50 broadcast stations: 30 FM band and 20 AM stations can be stored to the preset memory.

• During tuner mode, find a desired station.

• Press MEM/PROG/P-MODE key to activate memory setting mode.

• Press -10/MEM – key or +10/MEM + key to choose the desired memory location. The location number is flashing on the left side of the screen.

• Press MEM/PROG/P-MODE key again to store the desired station.

• Repeat steps for storing stations to other locations.

• To clear the memory of any location simply save a new station to the same memory.

Selecting stored stations

• Press -10/MEM – key or +10/MEM + key to choose the memory location. The stored station will be selected.

Antenna

• For FM reception, adjust the telescopic antenna appropriately to obtain the best reception on the band selected.

• The AM signals are picked up through the built-in ferrite antenna. The set should be placed to a position for the best reception.

FM and FM stereo reception

• In particular when stereo signal is weak and much noise are received, it is preferable to receive the program in mono. Press FOLDER/FM-MODE button to switch between FM stereo and mono modes.

Compact disc operation

Insertion and removal of discs

• When opening the CD-door, always ensure the disc is not in motion (not spinning) when you open the CD-door. Always press "STOP" button to stop the disc spinning first.

• Place a CD into the compartment with the label-side (printed side of disc) facing upwards. Press down in the center part of disc until the disc "locks" onto the center spindle.

• When the CD has been placed onto the center spindle, gently lower the CD-door downwards until it locks shut.

• The CD is now ready to be played.

• To remove a disc, follow the same procedure as described above, except to remove the CD instead of inserting it into the compartment, by placing one

finger at the middle of disc (center spindle) & the other at the edge of the disc & gently pulling upwards.

Important : Always hold a CD by its edges. Avoid getting any finger prints, smudges or dirt onto the surface of a disc. In case this happens, use a special CD-cleaning cloth or cleaning kit to remove the dirt or smudges. Important: Please make sure to always fold down the handle before opening the CD door.

• Press ON/OFF key once to switch on the system power.

• Press CD key to enter CD mode.

• Put a CD into the CD compartment and close the CD door.

• The display will indicate "READ" for a few seconds and then start to play the first track.

• The display will indicate the current track number and playback time.

Play/pause mode

• Press the PLAY/PAUSE button to pause at any track when playing. Press PLAY/PAUSE button again to resume playing.

• To stop the CD, press the STOP button. If you press PLAY/PAUSE button now the playback will start from first track.

Skip and search mode

• Press the NEXT/TUNE UP button once to skip to the next track. Press and hold this button to search for a particular point at high speed forward. Release the button to resume normal play.

• Press the BACK/TUNE DOWN button once to the beginning of the current track. Press the BACK/TUNE DOWN button twice to skip back to previous track. Press and hold this button to search for a particular point at high speed backward. Release the button resume normal play.

Repeat, intro and random modes

• Press the MEM/PROG/P-MODE key repeatedly to select the following options:

- REPEAT – to repeat the current track

- REPEAT ALL – to repeat all tracks (full CD, USB or SD)

- INTRO – to "sample" all the music on the CD/USB/SD (about first 12 seconds of every song will be played)

- RANDOM – to play a random mix of all the songs on CD/USB/SD

Program mode

• Up to 60 tracks can be programmed for disc play in any order or the same track can be repeated up to 60 times.

• Before use, be sure to stop the CD by pressing the STOP button.

• Press the MEM/PROG/P-MODE key. The display will show "P01". This indicates that the set is now in memory programming mode, at the first memory

position.

• Select a desired track by using the BACK/TUNE DOWN and NEXT/TUNE UP buttons.

• Press the MEM/PROG/P-MODE key again to confirm.

• The set will advance to next memory position, the display will show "P02".

• Repeat steps described above to enter additional memories into the program if necessary.

• After a maximum of 60 songs (or less) have been selected as described above, press the PLAY/ PAUSE button to start playing the programmed tracks.

• The "PROG" symbol will appear to indicate that you have saved a program-memory (sequence).

• The program memory will be cleared when you press STOP button twice.

+ 11 hidden pages