Hyundai D46KFA, D46CFA, D558FA, D552FA User Manual

User’s Guide

MODELS : D46KFA, D46CFA,

D558FA, D552FA

U.S.A.

U.S.FEDERAL COMMUNICATIONS COMMISSION RADIO FREQUENCY INTERFERENCE STATEMENT INFORMATION TO THE USER

NOTE : This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet of a circuit different from that to which the

receiver is connected. Consult the dealer or an experienced radio/Monitor technician for assistance.

Changes or modication not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Connecting of peripherals requires the use of grounded shielded signal cables.

DECLARATION OF CONFORMITY

For the following product :

All of Digital sigange HYUNDAI IBT provides

Manufactured at :

(factory name, address)

Hyundai IBT Co., Ltd. 106, Apogongdan-gil, Gimcheon-si, Gyeongsangbuk-do, 740-862 Republic of Korea

We herewith confirmed to comply with the requirements set put in the Council Directive on the Approximation of the Lows of the Member States relating to Electromagnetic Compatibility Directive (89/336/EEC), Low-Voltage Directive(73/23/EEC , 93/68/EEC) . For the evaluation regarding the Directives, the following standards were applied:

EN60065/2002 + A1:2006 + A11:2008 + A2:2010 + A12:2011 EN55022 : 2006 EN55024/A2 : 2003 EN61000-3-2 : 2006 EN61000-3-3 : 2008

DIGITAL SIGNAGE

Contents

Major features ........................................................................................................... 2

Safety Information .................................................................................................... 2

Be sure to understand ..............................................................................................5

Check the product list ............................................................................................... 6

Proper location for product installation .................................................................. 7

Installing a Bracket ...................................................................................................8

Title and function of each part ..............................................................................10

Adjusting OSD and explanation of its function ...................................................15

Diagnosis ................................................................................................................. 34

Specifications ..........................................................................................................36

* REMOTE CONTROL / RS232C COMMAND SPEC

English

DIGITAL SIGNAGE

Major features

Safety Information

This product has been designed to enable the user ease of use, and display information effectively and conveniently.

• TFT LCD Module adopted • Vivid digital color display

• OSD control function • Automatic Image control

• Automatic temperature control • High speed response

• Built in multi-vision function • Low power consumption

• HDMI, DVI, D-Sub input & DVI, D-Sub output

This product is designed to ensure user's safety.

Avoid the following items to prevent serious electric shot and other dangers.

- Do not place wet objects on or around the product or the power cord.

- Do not cover or insert anything over or into the ventilation openings.

- Do not place in a location where damage can be caused by oil, smoke, high temperature,

high humidity, dust etc.

- The product is not suitable for use at visual display workplaces according to §2 of the German Ordinance for Work with Visual Display Units.

The main plug of the power supply cord shall remain readily operable.

- An apparatus with CLASS I construction shall be connected to a Mains socket outlet

with a protective earthing connection.

- Make sure that the power cord and other cables are correctly plugged in.

- Plug the power cord correctly into the end, do not wobble/jiggle, it may cause electric shock fire.

DIGITAL SIGNAGE

- Do not touch the power cord with wet hands, it may cause electric shock.

- Overloaded AC outlets and extension cables are as dangerous as the power cord being damaged,

call service engineer for replacement as it may cause electric shock or fire.

- Do not use multiple devices in a single power outlet, it may cause overheating or fire.

- Do not use or place sharp objects near the LCD surface, as this can cause damage to the screen itself.

- When cleaning the LCD screen / Surface, do not use chemical cleaning products as this can seriously damage the special coatings on the screen. Only use water to dampen a soft cloth and

lightly clear the screen.

- Over time dust deposits can build up inside the product, this can cause the product to overheat

thus causing premature malfunction or fire. Please do not attempt to clean the inside of the product yourself, please contact the local service agent.

- Do not use alcohol or strong chemical solvent such as methyl, ethyl or a Isopropyl.

- In the case of cleaning, be sure to remove the power cord and wipe with a soft dry fabric.

- Keep batteries for the remote control out of children's sight.

- Batteries should be inserted using the correct polarity (+,-).

- Use only new batteries, do not mix old & new.

- Risk of Explosion if Battery is replaced by an Incorrect Type. Dispose of Used Batteries

According to the Instructions.

- Place unit on a stable bracket or surface.

- More than 2 people should work together when moving or installing.

- Do not hang on or jump to the product or mounting rack.

- When the product is left unused for a long time, be sure to unplug the power cord.

- In the case of damage or breakage do not attempt to self repair, please contact local service

engineer.

English

DIGITAL SIGNAGE

- In case of Kiosk Model, keep installing the product on the flat location and fixing the wheels not to move itself or fall down.

- On Kiosk Model, make sure to turn off the power before connecting cables.

- This manual contains general instructions for the display products only so refer to the provided CD-ROM manual and the driver installation manual for the driver installation

instructions for touch screen and/or touch screen itself.

- The apparatus shall not be exposed to dripping or splashing and that no objects filled with

liquids, such as vases, shall be placed on the apparatus.

- Shall be connected to a MAINS socket outlet with a protective earthing connection.

- The disconnect device shall remain readily operable.

- The socket-outlet shall be installed near the equipment and shall be easily accessible.

- Use only with a cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

DIGITAL SIGNAGE

Be sure to understand

Image quality of the product

CAUSE

Due to the nature of LCD's property, Afterimage can occur. Afterimage appears when

identical frames / images are displayed continuasly. If displayed for prolonged periods of time this can become permanent.

PREVENTION

When you display a freeze frame for a long time, lower the brightness and contrast (Brightness, 70/ Contrast, 80). Also it can be prevented by using moving frame.

COUNTERMEASURES

Temporary afterimage can be alleviated by displaying white or moving frame about 10

hours.(But, permanent afterimage cannot be disappeared according to the property of LCD) This method is used to remove temporary afterimage that may occur after

displaying a still frame for a certain time.

It can take several minutes or hours to remove afterimage according to the severity. In

the case that your cannot avoid displaying identical still image continuously, you can prevent it by displaying moving image for 2 or 3 minutes in every hour. As the brightness of still image and time of display are the cause of afterimage, you are recommended to

lower the brightness in that case.

Above problem shall not be covered by warranty.

English

DIGITAL SIGNAGE

Check the product list

Please check the following components provided with the product after you open the box.

Remote control

Power Cord HDMI cable HDMI to DVI Cable (Option)

CD Manual &Sheet D-SUB Cable RS232C Cable (Option)

please check the following components provided with the product after you open

the box and contact the dealer if any missing.

* The contents may vary depending on models and sometimes the contents may be attached on the product.

DIGITAL SIGNAGE

Proper location for product installation

Portrait Mode

1. Locate the product at least 30cm away from the electric appliance or heating product.

2. The product must be placed at least 10cm away from the wall and ground.

3. Keep the product out of direct ray of light and locate screen not to be reflected by the

sunlight.

4. Make sure the mounting rack firmly tightened before installation.

Please take extra care during installation, it is possible to cause damage if the unit is

handled badly or knocked.

- Only on some models.

- When installing in portrait mode, rotate the monitor clockwise

English

DIGITAL SIGNAGE

Installing a Bracket

- A type

- The contents may vary depending on models

DIGITAL SIGNAGE

Installing a Bracket

- B type

- The contents may vary depending on models

English

DIGITAL SIGNAGE

POWER

SOURCE MENU

SELECT

VOL

Title and function of each part

Power button ; to turn the power on or off.

Input selection button : to select other connected

device.

Menu button : to display menu or exit from the menu.

Select button.

2 3 4 5 6 7

To move down in OSD menu.

To move up in OSD menu.

To move left and control the volume down in OSD menu.

To move right and control the volume up OSD menu.

+ 30 hidden pages