Hyundai D705ML, D575ML, D255ML, D460ML, D420ML User Manual

...

D525ML_ENG_01.indd 1 2008.9.4 1:33:27 PM

U.S.A.

U.S.FEDERAL COMMUNICATIONS COMMISSION RADIO FREQUENCY INTERFERENCE STATEMENT INFORMATION TO THE USER

NOTE : This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in a residential installation.This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet of a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for assistance.

Changes or modification not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

Connecting of peripherals requires the use of grounded shielded signal cables.

D525ML_ENG_01.indd 2 2008.9.4 1:33:30 PM

DIGITAL SIGNAGE

DECLARATION OF CONFORMITY

WE HYUNDAI IT CORP.

Ami-ri Bubal-Eub Ichon-Si Kyungki-Do 467-860 KOREA

declare under our sole responsibility that the product:

to which this declaration relates is in conformity with the following standard(s) or other normative document(s)

following the provisions of the Low Voltage Directive 73/23/EEC, 93/68/EEC and the EMC Directive 89/336/EEC.

Jong Won, Choi Ho Suk, Chon

(Name and signature of authorized person)

KOREA / July 1, 2008

(Place and date of issue)

Kind of equipment : DID Type-Designation : S40M0G010 / LT46DW001 / S57M0F010

Safety : EN60950-1:2002 EMC : EN 55022/1998+A1:2000+A2:2003 EN 55024 :1998+A1:2001+A2:2003 EN 61000-3-2:2000 EN 61000-3-3:1995+A1:2001

TUV SUD Product Service GmbH Zertifizierstelle, Ridlerstrasse 65, 80339 Munchen, Germany

Accredited testlaboratory TÜV Rheinland Am Grauen Stein 51105 Köln

LT46DW001 :

S40M0G010 : S57M0F010

D525ML_ENG_01.indd 3 2008.9.4 1:33:31 PM

DIGITAL SIGNAGE

Major features ...................................................... 1/34

Direction for the use ........................................... 1/34

Be sure to understand ......................................... 3/34

Checking product list .......................................... 5/34 Proper place for product Installation

........................................................... 6/34

Title and function of each part .......................... 7/34

Front part .............................................................. 7/34

Rear part .............................................................. 8/34

Remote control ...................................................... 9/34

How to insert battery into remote control .............. 9/34

How to connect HDMI ....................................... 10/34

Support timing for Digital RGB ........................... 11/34

Corrections

How to connect analog RGB (PC D_SUB) ........12/34

Supporting timing for PC ..................................13/34

How to Connect component ..........................14/34

Supporting timing for component & AV ............15/34

How to Connect the video ..............................16/34

OSD adjustment and fucntion .........................17/34

Diagnosis ...........................................................31/34

Product specification .......................................33/34

ENGLISH

D525ML_ENG_01.indd 4 2008.9.4 1:33:33 PM

DIGITAL SIGNAGE

-1/34-

DIGITAL SIGNAGE

Major features

Direction for the use

This product has been designed to enable the user ease of use, and display information effectively and conveniently.

• TFT LCD Module adopted

D320ML/D400ML/D420ML/D460ML : 1366 x 768 WXGA (HD)

D525ML/D575ML/D705ML : 1920 x 1080 UWXGA (FHD)

• vivid digital color display

• OSD control function

• Automatic Image control

• Automatic temperature control

• Analog/Digital RGB(HDMI) input and output

• Y Pb Pr/AV input and output

• Built in multi-vision function

This Product is designed to ensure user's safety. Avoid the following items prevents from serious electric shot and other dangers.

- Do not place wet objects on or around the product or the power cord.

- Do not cover or insert anything over or into the ventilation openings.

- Do not place in a location where damaged from oil, Smoke, high temperature, high humidity, dust etc can be caused.

D525ML_ENG_01.indd 1 2008.9.4 1:33:33 PM

DIGITAL SIGNAGE

-2/34-

ENGLISH

- The product is not suitable for use at visual display workplaces according to §2

of the German Ordinance for Work with Visual Display Units.

- The mains plug of the power supply cord shall remain readily operable.

- An apparatus with CLASS I construction shall be connected to a Mains socket outlet

with a protective earthing connection.

- Make sure the power cord and other cables are correctly plugged in.

- Plug the power cord correctly into the end, do not wobble/jiggle, it may cause electric shock fire.

- Do not touch the power cord with wet hands, it may cause electric shock.

- Overloaded AC outlets and extension cables are as dangerous as the power cord being damaged, call service engineer for replacement as it may cause electric shock or fire.

- Do not use multiple devices in a single power outlet, it may cause overheating or fire.

- Do not use or place sharp objects near the LCD surface, as this can cause damage to the screen itself.

- When cleaning the LCD screen / Surface, do not use chemical cleaning products as this can seriously damage the special coatings on the screen. Only use water to dampen a soft cloth and lightly clear the screen.

- Over time dust deposits can build up inside the product, this can cause the product to overheat thus causing premature malfunction or fire. Please do not attempt to clean the inside of the product yourself, please contact the local service agent.

- Do not use alcohol or strong chemical solvent such as methyl, ethyl or a Isopropyl.

- In the case of cleaning, be sure to remove the power cord and wip with a soft dry fabric.

- Keep batteries for the remote control out of children's sight.

- Make sure that power cord or other cables are correctly plugged in.

D525ML_ENG_01.indd 2 2008.9.4 1:33:34 PM

DIGITAL SIGNAGE

-3/34-

DIGITAL SIGNAGE

Be sure to understand

- Batteries should be inserted using the correct polarity (+,-).

- Use only new batteries, do not mix old & new.

- Place unit on a stable bracket or surace.

- More than 2 persons should work together when moving or installing.

- Do not hang on or jump to the product or mounting rack.

- When the product be left unused for a long time, be sure to unplug the power cord.

- In the case of damage or breakage do not attempt to self repair, please contact local service engineer.

Image quality of the product

CAUSE

- Due to the nature of LCD's property, Afterimage can occur. Afterimage appears when identical frames / images are displayed continuasly. If displayed for prolonged periods of time this can become permanent.

PREVENTION

When you display a freeze frame for a long time, lower the brightness and contrast (Brightness, 70/ Contrast, 80). Also it can be prevented by using moving frame.

D525ML_ENG_01.indd 3 2008.9.4 1:33:34 PM

DIGITAL SIGNAGE

-4/34-

ENGLISH

PREVENTION

Temporary afterimage can be alleviated by displaying white or moving frame about 10

hours.(But, permanent afterimage cannot be disappeared according to the property of LCD) This method is used to remove temporary afterimage that may occur after displaying a still frame for a certain times.

It can take several minutes or hours to remove afterimage according to the severity. In

the case that your cannot avoid displaying identical still image continuously, you can prevent it by displaying moving image for 2 or 3 minutes in every hour. As the brightness of still image and time of display are the cause of afterimage, you are recommended to lower the brightness in that case.

Above problem shall not be covered by warranty.

D525ML_ENG_01.indd 4 2008.9.4 1:33:34 PM

DIGITAL SIGNAGE

-5/34-

DIGITAL SIGNAGE

Please check the following components provided with the product after you open the box.

please check the following components provided with the product after you open the box and contact the dealer if any missing.

Check the product list

HDMI cable

Remote control &

batteries

Power Cord

User's manual

Product

HDMI to DVI Cable

(Option)

D-SUB Cable

(Option)

RS232C Cable

(Option)

D525ML_ENG_01.indd 5 2008.9.4 1:33:36 PM

DIGITAL SIGNAGE

-6/34-

ENGLISH

Proper location for product installation

1. Locate the product at least 30cm away from the electric appliance or heating product.

2. The product must be placed at least 10cm away from the wall and ground.

3. Keep the product out of direct ray of light and locate screen not to be reflected by the

sunlight.

4. Make sure the mounting rack firmly tightened before installation.

Please take extra care during installation, it is possible to cause damage if the unit is handled badly or knocked.

D525ML_ENG_01.indd 6 2008.9.4 1:33:37 PM

DIGITAL SIGNAGE

-7/34-

DIGITAL SIGNAGE

Title and function of each part

Front panel

Remote control receiving sensor.

Power display LED red-stand by/ Green-working.

~ OSD button.

Power button ; to turn the power on or off.

Input selection button : to select other connected

device.

Menu button : to display menu or exit from the menu.

select button.

To move down in OSD menu.

To move up in OSD menu.

To move left and control the volume down in OSD menu.

To move right and control the volume up OSD menu.

2 3 4 5 6 7 8 9

POWER

SOURCE MENU

SELECT

VOL

D525ML_ENG_01.indd 7 2008.9.4 1:33:38 PM

+ 27 hidden pages