Hytronik HMW31 User Manual

Download

IP65 High Bay HF Motion Sensor

HMW31

1-10V Dimming with Remote Control

Technical Data

Input Characteristics

Model No.

Mains voltage Stand-by power

Load ratings:

Capacitive

Resistive

400VA@120V; 800VA@220 -277V

800W@120V; 1600W@220 -277V

HMW31

120~277VAC 50/60Hz

<1W

20sWarming-up

Sensor Data

Model No.

Operation frequency

Transmission power

Detection range

Detection angle

HMW31

High Frequency (microwave) Sensor principle

5.8GHz +/- 75MHz

<0.2mW

Max. ( O x H) 10m x 15m

360

Safety and EMC

EMC standard (EMC)

Safety standard (LVD)

Radio Equipment (RED)

Certication

EN55015, EN61000

EN60669-1, EN60669-2-1

EN300440, EN301489-1,

EN62479

Semko, CB, CE , EMC, RED, RCM

Mechanical Structures and Installations

For more details, please refer to user manual.

A. Ceiling mount

Daylight sensor

LED indicator

Environment

Operation temperature

IP rating

Rotary switch

Infrared receiver

Ta: -20OC ~ +70OC

IP65

4.1

80.7

91.5

IP65RED

313

Hytronik Microwave motion sensor

Sensor module

Installation rack

Cable entry

4.1

66.6

81.5

59.3

57.3

47.5

www.hytronik.com

24.5

B. Screw to the Luminaire by conduit

C. Attach to the shade by clamp

LED indicator

Daylight sensor

Sensor module

Rotary switch

Infrared receiver

Cable entry

59.3

57.3

47.5

59.6

66.6

89.9

0.825”

35.2

ぶ

4.5

28.5

ぶ

LED indicator

Daylight sensor

Sensor module

*OUFMMJHFOU 1IPUPDFMM

0OF,FZ $PNNJTTJPOJOH

Rotary switch

Infrared receiver

"NCJFOUEBZMJHIU

UISFTIPME

Angle adjustment

Luminaire clamp

3PUBSZ4XJUDI

1SPHSBNJOH

%FUFDUJPO1BUUFSO



33.7

59.6

66.6

59.3

84.5





163.2

Functions and Features

Intelligent Photocell (daylight detection prior to motion detection)

The built-in photocell will also automatically turn off the light when the ambient natural light exceeds the programmed lux level for more than 5min, regardless of whether motion is detected or not. This feature can be disabled if it is required that the xture stays at dimmed level during absence.

With sufcient natural light, the light

th sufcient natural light, the li does not switch on when presence is detected.

With insufcient natural light, the sensor

th insufcient natural light, the switches on the light automatically when presence is detected.

The sensor switches off the light when

he sensor switches off the li natural light is sufcient, even with presence.

Note: if the stand-by time is preset at "+∞", the xture never switches off but stays at preset dimming level even when natural light is sufcient.

www.hytronik.com

Hytronik Microwave motion sensor

314

Tri-level Control (Corridor Function)

Hytronik builds this function inside the motion sensor to achieve tri-level control, for some areas which require a light change notice before switch-off. The sensor offers 3 levels of light: 100%-->dimmed light (natural light is insufcient) -->off; and 2 periods of selectable waiting time: motion hold-time and stand-by period; Selectable daylight threshold and freedom of detection area.

Zero-cross Relay Operation

Designed in the software, sensor switches on/off the load right at the zero-cross point, to ensure that the in-rush current is minimised, enabling the maximum lifetime of the relay.

Rotary Switch Preset

A rotary switch is built inside the sensor for scene selection / fast programming. Total 16 channels are available:

Rotary switch preset

Note: settings can also be changed by remote control HRC-11. The last action controls.

zero-cross point

Channel Hold-time

Detection

range

0 5s100% Disable 1 1min100% 2Lux 2 5min100% 10Lux 3 5min100% 30Lux 4 5min100% 10Lux 5 5min100% 30Lux 6 5min100% Disable 7 10min100% 2Lux 8 10min100% 10Lux 9 10min100% 30Lux

A 10min100% Disable B 10min75% 30Lux C 10min50% 10Lux D 30min100% 50Lux E F

30min100% Disable 5s100%

Daylight sensor

Alternating current

Stand-by time

10s 5min 10min 30min 0s +∞ +∞ 10min 30min +∞

+∞ +∞ +∞ +∞ +∞ 10s

Stand-by dim level

10% 10% 10% 10% Disable 10% 30% 10% 10% 10%

30% 10% 10% 10% 30% 10%2Lux

Detection Pattern

Ceiling mounted height(m)



315

Hytronik Microwave motion sensor

Wiring Diagram





10%

30%

50%

75%

L N

Brown

Blue

Grey

Red

Black

LED driver

1-10V+

1-10V

HMW31

www.hytronik.com

Settings (Remote Control HRC-11)

ON/

Permanent ON/OFF function

OFF

Press button “ON/OFF” to select permanent ON or permanent OFF mode. * Press button “AUTO”, “RESET” to quit this mode.

mode will change to AUTO Mode after power failure.

The

Reset Settings

Press button “RESET”, all settings go back to rotary switch settings.

Shift Button

Press button “Shift”, the LED on the top left corner is on to indicate mode selection. All values / settings in RED are valid for 20 seconds.

AUTO mode

Press button “AUTO” to initiate automatic mode. The sensor starts working and all settings remain as before the light is switched ON/OFF.

Note: “Semi-auto” function is disabled.



III

Power output

Press the buttons to select light output at 80% (at initial 10,000 hours) or 100%.

Note: “Sensor off” and “Twilight” functions are disabled.

Brightness +/-

Press the buttons to adjust the light brightness during hold-time.

Load Indication: The light will ash ONCE rapidly after receiving the commamd from the remote control successfully.

HRC-11

Scene program - 1-key commissioning

1. Press button “Start” to program.

2. Select the buttons in “Detection range”, “Daylight threshold”, “Hold-time”, “Stand-by time”, “Stand-by dimming level” to set all parameters.

3. Press button “Memory” to save all the settings programmed in the remote control.

4. Press button “Apply” to set the settings to each sensor unit(s).

For example, to set detection range 100%, daylight threshold Disable, hold-time 5min, stand-by time +∞, stand-by dimming level 30%, the steps should be: Press button “Start”, button ”100%”, “Disable”, “Shift”, “5min”, “Shift”, “+∞”, “30%”, “Memory”. By pointing to the sensor unit(s) and pressing “Apply”, all settings are passed on the sensor(s).

Detection range

Press buttons in zone “Detection range” to set detection range at 100% / 75% / 50% / 10%.

Daylight threshold

Press buttons in zone “ Daylight threshold” to set daylight sensor at 2Lux/ 10Lux / 50Lux / 100Lux / 300Lux / 500Lux / Disable.

Note: To set daylight sensor at 100Lux / 300Lux / 500Lux, press “Shift” button rst.

www.hytronik.com

Hytronik Microwave motion sensor

316

Ambient daylight threshold

1. Press button “Shift”, the red LED starts to ash.

2. Press button “Ambient”, the surrounding lux level is sampled and set as the new daylight threshold.

Hold-time

Press buttons in zone “hold-time” to set the hold-time at 2s / 30s / 1min / 5min / 10min / 15min / 20min / 30min.

Note: 1. To set hold-time at 30s / 5min / 15min / 30min, press “Shift” button rst.

2. 2s is for testing purpose only, stand-by period and daylight sensor settings are disabled in this mode.

*To exit from Test mode, press button “RESET” or any button in “Hold-time”.

Stand-by time (corridor function)

Press buttons in zone “stand-by time” to set the stand-by period at 0s / 10s / 1min / 5min / 10min / 30min / 1h / +∞.

Note: “0s” means on/off control; “+∞” means bi-level control, the xture is 100% on when there is motion detected, and remains at the stand-by dimming level when no presence after motion hold-time.

Stand-by dimming level

Press the button in zone “stand-by dimming level” to set the stand-by dimming level at 10% / 20% / 30% / 50%.

Auto-conguration function

All buttons in this zone are disabled.

Dual tech & RF mode

All buttons are disabled.

317

Hytronik Microwave motion sensor

www.hytronik.com

Hytronik HMW31 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual