Hytera Communications EPRADGU1 User Manual

Preface

Thanks for your favor in our product. This manual provides guidance for you to use the product.
This manual is applicable to the following product:
E-PRAD(G)

Icon Conventions

The following icons are available through this manual:

Caution:

Note:

Indicates situations that could cause data loss or equipment damage.

Indicates references that can further describe the related topics.

Copyright Information

Hytera is the trademark or registered trademark of Hytera Communications Corporation Limited (the
Company) in the People's Republic of China (PRC) and/or other countries or areas. The Company retains
the ownership of its trademarks and product names. All other trademarks and/or product names that may
be used in this manual are properties of their respective owners.

The product described in this manual may include the Company's computer programs stored in memory or
other media. Laws in PRC and/or other countries or areas protect the exclusive rights of the Company with
respect to its computer programs. The purchase of this product shall not be deemed to grant, either directly
or by implication, any rights to the purchaser regarding the Company's computer programs. The
Company's computer programs may not be copied, modified, distributed, decompiled, or
reverse-engineered in any manner without the prior written consent of the Company.

Disclaimer

The Company endeavors to achieve the accuracy and completeness of this manual, but no warranty of
accuracy or reliability is given. All the specifications and designs are subject to change without notice due
to continuous technological development. No part of this manual may be copied, modified, translated, or
distributed in any manner without the prior written consent of the Company.

We do not guarantee, for any particular purpose, the accuracy, validity, timeliness, legitimacy or
completeness of the third-party products and contents involved in this manual.

If you have any suggestions or would like to receive more information, please visit our website at:

http://www.hytera.com.

FCC Regulations

Federal Communication Commission (FCC) requires that all radio communication products should meet
the requirements set forth in the above standards before they can be marketed in the U.S, and the
manufacturer shall post a RF label on the product to inform users of operational instructions, so as to
enhance their occupational health against exposure to RF energy.

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to

part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates and can radiate radio frequency energy.
If not installed and used in accordance with the instructions, it may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation.
Verification of harmful interference by this equipment to radio or television reception can be determined by
turning it off and then on. The user is encouraged to try to correct the interference by one or more of the
following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a different circuit to that of the receiver's outlet.
Consult the dealer or an experienced radio/TV technician for help.
Operation is subject to the following two conditions:

This device may not cause harmful interference.

This device must accept any interference received, including interference that may cause undesired

operation.

Note: Changes or modifications to this unit not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.

Operational Instructions and Training Guidelines

To ensure optimal performance and compliance with the occupational/controlled environment RF energy
exposure limits in the above standards and guidelines, users should transmit not more than 50% of the
time and always adhere to the following procedures:

 Antenna gain must not exceed 3.5dBi.
 The antenna must be installed complying with the requirements of manufacturer or supplier, and it

must be at least 40cm away from human body.

Compliance with RF Exposure Standards

Hytera's radio complies with the following RF energy exposure standards and guidelines:

United States Federal Communications Commission, Code of Federal Regulations; 47 CFR § 1.1307,

1.1310 and 2.1091

American National Standards Institute (ANSI) / Institute of Electrical and Electronic Engineers (IEEE)

C95. 1:2005; Canada RSS102 Issue 5 March 2015

Institute of Electrical and Electronic Engineers (IEEE) C95.1:2005 Edition

ISEDC Statement

This device complies with Innovation, Science and Economic Development Canada Compliance
license-exempt RSS standard(s). Operation is subject to the following two conditions:

This device may not cause harmful interference.
This device must accept any interference received, including interference that may cause undesired

operation.

Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de
licence. L'exploitation est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de
brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d'en compromettre le fonctionnement

ISEDC Radiation Exposure Statement:

This device must be restricted to work related operations in an Occupational/Controlled RF exposure
Environment.

This equipment should be installed and operated with minimum di
your body.

ISEDC exposition aux radiations:
Ce dispositif doit être limité aux opérations liées au travail dans un environnement d'exposition RF

professionnel/contrôlé.
Cet équipement doit être installé et distance entre le antenne et votre

corps.

utilisé avec un minimum de 40cm de

stance 40cm between the antenna &

EU Regulatory Conformance

As certified by the qualified laboratory, the product is in compliance with the essential requirements and
other relevant provisions of the Directive:
 2014/53/EU
Please note that the above information is applicable to EU countries only.

The maximum antenna gain is 3.5dBi, which is calculated in the EIRP. The distance from observation point
to the antenna is 50cm.