Hytera Communications EPOLE100VHF User Manual

User Manual

Digital WANET Repeater

Preface

Thanks for your favor in our product. This manual provides guidance for you to use the product. To avoid
bodily injury and property loss caused by improper operations, please read the Safety Information
Booklet before using the product.
This manual is applicable to the following product:
E-pole Digital WANET Repeater

Icon Conventions

The following icons are available through this manual:

Caution:

Note:

indicates situations that could cause damage to your product.

indicates tips that can help you make better use of your product.

Copyright Information

Hytera is the trademark or registered trademark of Hytera Communications Corporation Limited (the
Company) in PRC and/or other countries or areas. The Company retains the ownership of its trademarks
and product names. All other trademarks and/or product names that may be used in this manual are
properties of their respective owners.
The product described in this manual may include the Company’s computer programs stored in memory
or other media. Laws in PRC and/or other countries or areas protect the exclusive rights of the Company
with respect to its computer programs. The purchase of this product shall not be deemed to grant, either
directly or by implication, any rights to the purchaser regarding the Company’s computer programs. Any
of the Company’s computer programs may not be copied, modified, distributed, decompiled, or
reverse-engineered in any manner without the prior written consent of the Company.

Disclaimer

The Company endeavors to achieve the accuracy and completeness of this manual, but no warranty of
accuracy or reliability is given. All the specifications and designs are subject to change without notice
due to continuous technology development. No part of this manual may be copied, modified, translated,
or distributed in any manner without the prior written consent of the Company.
We do not guarantee, for any particular purpose, the accuracy, validity, timeliness, legitimacy or
completeness of the Third Party products and contents involved in this manual.
If you have any suggestions or would like to learn more details, please visit our website at: http://www.

hytera.com.

FCC Regulations

Federal Communication Commission (FCC) requires that all radio communication products should meet
the requirements set forth in the above standards before they can be marketed in the U.S, and the
manufacturer shall post a RF label on the product to inform users of operational instructions, so as to
enhance their occupational health against exposure to RF energy.

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates and can radiate radio frequency
energy. If not installed and used in accordance with the instructions, it may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a particular
installation. Verification of harmful interference by this equipment to radio or television reception can be
determined by turning it off and then on. The user is encouraged to try to correct the interference by one
or more of the following measures:

 Reorient or relocate the receiving antenna. Increase the separation between the equipment and

receiver.

 Connect the equipment into an outlet on a different circuit to that of the receiver's outlet.
 Consult the dealer or an experienced radio/TV technician for help.

Operation is subject to the following two conditions:

 This device may not cause harmful interference.

 This device must accept any interference received, including interference that may cause undesired

operation.

Note: Changes or modifications to this unit not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.

Operational Instructions and Training Guidelines

To ensure optimal performance and compliance with the occupational/controlled environment RF energy
exposure limits in the above standards and guidelines, users should transmit not more than 50% of the
time and always adhere to the following procedures:

 Antenna gain must not exceed 3.2dBi for DMR and 1.0dBi for GSM850 and 3.5 for PCS1900.
 The antenna must be installed complying with the requirements of manufacturer or supplier, and it

must be at least 0.5 meters away from human body.

Compliance with RF Exposure Standards

Hytera's radio complies with the following RF energy exposure standards and guidelines:

 United States Federal Communications Commission, Code of Federal Regulations; 47 CFR §

1.1307, 1.1310 and 2.1091

 American National Standards Institute (ANSI) / Institute of Electrical and Electronic Engineers (IEEE)

C95. 1:2005; Canada RSS102 Issue 5 March 2015

Institute of Electrical and Electronic Engineers (IEEE) C95.1:2005 Edition

ISEDC Statement

This device complies with Innovation, Science and Economic Development Canada Compliance
license-exempt RSS standard(s). Operation is subject to the following two conditions:

 This device may not cause harmful interference.
 This device must accept any interference received, including interference that may cause undesired

operation.

Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts
de licence. L'exploitation est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire
de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d'en compromettre le fonctionnement.

ISEDC Radiation Exposure Statement:

This device must be restricted to work related operations in an Occupational/Controlled RF
exposure Environment.

This equipment should be installed and operated with minimum distance 50cm between the
antenna & your body.

ISEDC exposition aux radiations:
Ce dispositif doit être limité aux opérations liées au travail dans un environnement

d'exposition RF professionnel/contrôlé.
Cet équipement doit être installé et utilisé avec un minimum de 50cm de distance entre le

antenne et votre corps.

EU Regulatory Conformance

As certified by the qualified laboratory, the product is in compliance with the essential requirements and
other relevant provisions of the Directive:

 2014/53/EU
 2006/66/EC
 2011/65/EU
 2012/19/EU

Please note that the above information is applicable to EU countries only.

The maximum antenna gain is 3.5dBi, which is caculated in the EIRP. The distance from observation
point to the antenna is 60cm.

Restrict use warning:



AT BE CY CZ DK

EE FI FR DE EL

HU IE IT LV  LT

LU MT NL PL PT

SK SI ES SE UK

BG RO HR 

Contents

1. Checking Items in the Package ......................................................................................................... 1

2. Product Descriptions ......................................................................................................................... 2

3. Installation .......................................................................................................................................... 4

3.1 Installation Requirements ............................................................................................................... 4

3.2 Pre-Installation Tasks ..................................................................................................................... 5

3.3 Device Installation ........................................................................................................................... 6

3.4 Cables Installation......................................................................................................................... 11

3.5 Post-installation Check ................................................................................................................. 12

4. Basic Operations .............................................................................................................................. 13

4.1 Power on ....................................................................................................................................... 13

4.2 Power off ....................................................................................................................................... 13

5. Troubleshooting ............................................................................................................................... 14

6. Care and Cleaning ............................................................................................................................ 15

7. Optional Accessories ....................................................................................................................... 16

8. Scope and Duration of Warranty ..................................................................................................... 17

i

1. Checking Items in the Package

Please unpack carefully and check if all items listed below are received. If any item is missing or
damaged, please contact your dealer.

Name Qty Name Qty

Mainframe 1 DC Wire 1

AC Wire 1 Owner’s Manual 1

Note

All pictures in this manual are for reference only.

1