Hytera Communications EPACK100F4 User Manual

To Costumers

Thank you very much for your favor of our products! This manual aims to enable you

quickly grasp the use of the product.

This manual applies to the following model:

E-pack100 Digital WANET Repeater

Icon Conventions

The following icons are used in this manual. The explanation of icons are

as follows:

Icon Description

Indicates situations that could cause data loss or

Caution

equipment damage.

Indicates notes that serves as supplement, illustration

Comment

or emphasis to the main content.

Copyright Information

Hytera is the trademark or registered trademark of Hytera Communications

Corporation Limited (the Company) in People's Republic of C hina (PRC)

and/or other countries or areas. The Company retains the ownership of its

trademarks and pro duct names. All other trade marks and/or prod uct

names that may be used in this manual are properties of th eir respective

owners.

The prod uct described in this man ual may in clude the Compan y's

computer programs stored in memory or other media. Laws in PRC and/or

other countries or areas protect the exclusive righ ts of the Co mpany with

respect to its computer programs. The purchase of this product shall not be

deemed to grant, either directly or by implication, any rights to the

purchaser regarding the Compan y's computer programs. The Compan y's

i

computer programs may not be copied, modified, distributed, decompiled,

or reverse-engineered in any mann er without the prior w ritten consent of

the Company.

Disclaimer

The Compa ny ende avors to achieve the accuracy and completeness of

this manual, but no warranty of accuracy or reliability is given. All the

specifications and desig ns are subje ct to change without notice due to

continuous technological development. No part of this man ual may be

copied, modified, translated, or distributed in any manner without the prior

written consent of the Company.

We do not guar antee, for any pa rticular pur pose, the accuracy, validity,

timeliness, legitimacy or complet eness of the th ird-party pr oducts and

contents involved in this manual.

If you ha ve any sug gestions or w ould like to receive mor e in formation,

please v isit our website at: http ://www.hytera.com, or call our serv ice

hotline [phone].

Federal Communications Commission (FCC) Regulatory
Requirements

According to the Fed eral C ommunications Commission regulato ry

requirements, the terminals must comply with the FCC's rules on

radiofrequency radiation, otherwise t he prod ucts shall not be sold in the

ii

U.S market. Besides, the manufacture shall be a sked to post a label o n

products informing costumers of considerations and improving th e

costumers’ awareness of radiation protection.

Radiofrequency Radiation Control and Operation Instructions

In order to e nsure the best perform ance of products and ensure that the

radiation restrictions related to o ccupations or environme nts are met, the

delivery time shall not exceed 50% of the rated factor.

FCC Regulations

Federal Communication Commission (FCC) requires that all radio

communication products should meet the requirements set forth in the

above standards before they can be marketed in the U.S, and the

manufacturer shall post a RF label on the product to inform users of

operational instructions, so as to enhance their occupational health against

exposure to RF energy.

FCC Statement

This equipment has been tested and found to comply with the limits for a

Class B digital device, pursuant to part 15 of FCC Rules. These limits are

designed to provide reasonable protection against harmful interference in a

residential installation. This equipment generates and can radiate radio

frequency energy. If not installed and used in accordance with the

instructions, it may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a

iii

particular installation. Verification of harmful interference by this equipment

to radio or television reception can be determined by turning it off and then

on. The user is encouraged to try to correct the interference by one or

more of the following measures:

 Reorient or relocate the receiving antenna. Increase the separation

between the equipment and receiver.

 Connect the equipment into an outlet on a different circuit to that of the

receiver's outlet.

 Consult the dealer or an experienced radio/TV technician for help.

Operation is subject to the following two conditions:

 This device may not cause harmful interference.

 This device must accept any interference received, including

interference that may cause undesired operation.

Note: Changes or modifications to this unit not expressly approved by the

party responsible for compliance could void the user's authority to operate

the equipment.

Operational Instructions and Training Guidelines

To ensure optimal performance and compliance with the

occupational/controlled environment RF energy exposure limits in the

above standards and guidelines, users should transmit not more than 50%

of the time and always adhere to the following procedures:

 DMR Antenna gain must not exceed 3.5dBi.

iv

 The antenna must be installed complying with the requirements of

manufacturer or supplier, and it must be at least 42 cm away from
human body.

Compliance with RF Exposure Standards

Hytera's radio complies with the following RF energy exposure standards

and guidelines:

 United States Federal Communications Commission, Code of Federal

Regulations; 47 CFR § 1.1307, 1.1310 and 2.1091

 American National Standards Institute (ANSI) / Institute of Electrical

and Electronic Engineers (IEEE) C95. 1:2005; Canada RSS102 Issue 5
March 2015

Institute of Electrical and Electronic Engineers (IEEE) C95.1:2005 Edition

ISEDC Statement

This device complies with Innovation, Science and Economic Development

Canada Compliance license-exempt RSS standard(s). Operation is subject

to the following two conditions:

 This device may not cause harmful interference.

v

 This device must accept any interference received, including

interference that may cause undesired operation.

Le présent appareil est conforme aux CNR d'Industrie Canada applicables

aux appareils radio exempts de licence. L'exploitation est autorisée aux

deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage,

et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique

subi, même si le brouillage est susceptible d'en compromettre le

fonctionnement

ISEDC Radiation Exposure Statement:

This device must be restricted to work related operations in an

Occupational/Controlled RF exposure Environment.

This equipment should be installed and operated with minimum distance

42cm between the radiator & your body.

ISEDC exposition aux radiations:

Ce dispositif doit être limité aux opérations liées au travail dans un

environnement d'exposition RF professionnel/contrôlé.

Cet équipement doit être installé et utilisé avec un minimum de 42cm de

distance entre le radiateur et votre corps.

vi

EU Regulatory Conformance

As certified by the qualified laboratory, the product is in compliance with

the essential requirements and other relevant provisions of the Directive:

2014/53/EU

2006/66/EC

2011/65/EU

2012/19/EU

Please note that the above information is applicable to EU countries only.

The maximum antenna gain is 3.5dBi, which is calculated in the EIRP. The

distance from observation point to the antenna is 120cm.

vii

Content

1. Packing List .......................................................................................... 1

2. Product Component ............................................................................. 2

2.1 Host .................................................................................................. 2

2.2 Palm Microphone .............................................................................. 4

3. Installation ............................................................................................ 6

3.1 Installation Requirements ................................................................. 6

3.2 Host Installation ................................................................................ 6

3.3 Check after Installation ..................................................................... 8

4. Basic Operation .................................................................................... 9

4.1 Power on .......................................................................................... 9

4.2 Power off .......................................................................................... 9

4.3 GSM Link Building ............................................................................ 9

4.4 Switch Channel ................................................................................. 9

4.5 Host Information Query ..................................................................... 9

5. Fault Handling .................................................................................... 11

6. Maintenance and Cleaning ................................................................ 14

7. Accessories Purchase ....................................................................... 15

8. Scope and Duration of Warranty ...................................................... 16

viii

1. Packing List

The packing case conta ins the following items. If there is any loss or da mage, please

contact the dealer or our company.

Items

Host 1 Palm Mircophone 1

Antenna 1 Mannual 1

Battery 1

Number

Items Number

Comment

The pictures in this manu al are for re ference on ly. Ple ase refer to the actual

products.

1

2. Product Component

2.1 Host

Num. Item Description

1

2

Battery Buckle

Operation Indicator

Toggle b uckle in th e dir ection of th e arr ow o f
battery buckle and pull out or insert the battery.

Operation st atus indic ation and the o peration
indicator turns to flickerin g (the freq uency is 1s)
and green if the host is operating properly.

2

Num. Item Description

3

4

5

6

7

8

9

10

RF Antenna

Interface

Data Interface

Palm Microphone

Interface

Power Button

Backpack Hole

Electric Quantity

Button

Indicator

Battery

Used to c onnect RF a ntenna for signal
transmission and reception.

The interface type is the UHF interface.

Used for the host debu gging and interc onnection
with center through IP network.

Connect palm microphone.

Used to contro l power on an d off. Long pres s the
button for 1s to po wer on, and l ong pres s the
button for 3s to power off.

Used for device installation in the backpack.

Touch the batter y l evel b utton, an d the p resent
power level can be chec ked throug h po wer
indicator.

Supply power for the host.

3

2.2 Palm Microphone

10

2

3

4
5

1

6
7

8

9

Num. Item Description

1

2

3

4

5

6

PTT Button Press the button to send a voice message.

Alarm Button Press the b utton to i nitiate a n emergency

alarm.

Power Button Press the button to power on and off.

Indicator Operation status indic ation of palm

microphone.

MIC Voice can be transmitted through MIC.

Display Area Display status icons, ca lling informati on,

etc.

4

Num. Item Description

7

8

9

10

Keyboard Function keys.

Speaker The sound can be pla yed through the

speaker.

Aviation Plug Connect with the host.

Aviation Knob Fix the aviation.

5

3. Installation

3.1 Installation Requirements
Installation Position

The host can be installed inside the backpack, and on the operation platform as well.

3.2 Host Installation

The installation steps are as follows:

1. （Optional）SIM card Installation

If voice business through GSM link is in need, a SIM card can be installed in the

position as the figure below.

2. Battery installation in the back of the host

Aim the charging port to the main body, and then toggle the buckle in the direction of

battery buckle arrow. Next, don’t stop pushing the battery until it can’t be pushed any

further, and then loosen the battery buckle, as shown in the figure below.

6

2

1

3. Install the host as needed, such in a backpack or on a platform.

When the host is installed in a backpack, the backpack hole should be fixed with the

backpack using a screw.

4. The threaded end of sucker antenna should be inserted in the RF interface at the top

of the host, and then screw it in clockwise direction.

Note:

Please don’t power up the device when one carries it. When the device is operating, the

distance between a man and the antenna should be at least 2 meters. Our company

7

shall not take any responsibility if there were any consequece caused by operations

now following the above rules.

3.3 Check after Installation

After the whole insta llation process, the host can be po wered on. The proper

functioning of the host can be checked b y watching the status of the LED light on the

front panel. T he power indicator will be cons tantly red, and the oper ation indicator will

be gre en and flickering if the host functions properly. Besides, the operation status of

the host can be checked through palm microphone.

8

4. Basic Operation

4.1 Power on

Long press Power Button for 1s, and then the power indicator will be constantly green.

Comment

The palm microphone can power on the host if the two are connected.

4.2 Power off

Long press Power Button for 3s, and then the power indicator will extinguish.

4.3 GSM Link Building

Voice business through GSM link can be realized by using an external palm

microphone connecting with the host.

1. Connect the external palm microphone to the host.

2. Enter the GSM contact list, and then select the default GSM contact.

3. Press and hold PTT button, and then the GSM link can be built.

4.4 Switch Channel

When the external palm microphone is connected to the host, the 10 default alternative

channels can be switched to be the present channel through menu in the palm

microphone.

4.5 Host Information Query

When the external palm microphone connects to the host, the frequency, signal

strength, battery level and other information of the host can be checked through the

display screen of the palm microphone, as shown in the table below.

9

Operation Operation Method

Wireless Link

Signal Strength

Check

GSM Signal

Strength Check

GSM Link Status

Check

Power Level Check

Battery Level

Check

Enter the main interface of palm microp hone, as sho wn in

the figure below.

10

5. Fault Handling

Description Cause Analysis Solution

Check whether the

Power-On Failure

The battery i s not properl y

installed or in bad contact.

Low battery.

The sendin g and rec eiving

frequency ar e not consisten t

battery is correctly and

firmly installed is correct

and firm

Touch the battery display

button to check the

current battery level. In

case the battery runs out

of power, please charge

the battery first or

connect the external

power for power supply,

then try to power on.

Check whether the

frequency is consistent,

and please contact

Communication

failure between

E-pack100

between E-pack100.

The work frequenc y po int is

disturbed by strong signal and

unable to transmit usefu l

signal.

11

dealer to reset the device

if necessary.

Find the interference

source, and if unable to

shut down or stay away

from it, please apply for

Description Cause Analysis Solution

another channel

frequency.

Short communication

distance, and unclear

voice

Other E-pack100 have left the

communication coverage of

this E-pack100.

E-pack100 antenna is in

abnormal connection

The connection cable is

damaged and the signal

energy leaks.

Cable joint connected to the

antenna port is loose or

detached cable.

Transmit power is too low

Cable is internal damaged.

Confirm and return to the

communication

coverage.

Check whether the

antenna is normally

connected.

Check the damage and

replace with new cable if

necessary.

Check and tighten the

joint. Replace it with new

joint if necessary.

Adjust the transmit power

to high power.

Please replace it with a

new cable

Find the interference source,

and if unable to shut down or

stay away from it, please

apply for another channel

frequency.

12

Find the interference

source, and if unable to

shut down or stay away

from it, please apply for

another channel

frequency.

If the above method doesn’t solve your problem, or there are any other problems,

please contact the local dealer or our company for more technical support.

13

6. Maintenance and Cleaning

In order to ensure the good performance of the product and prolong its service life,

please familiarize with the following contents for better daily maintenance and cleaning

of this product.

Maintenance

 Please do not use hard object puncture or scraping the product

 Please do not store the product in an environment containing corrosive electronic

circuitry

Cleaning

Caution

Please power off the product and disconnect the power connection before
cleaning.

 Please Use clean dry lint free or brush regularly to wipe the dust on the surface of

this product and the dust attached to the charging pole.

 The buttons and case of this product are easily to become dirty. Clean with neutral

detergent and non-woven fabric. Please do not use detergents, alcohol, sprays or

petroleum preparations to clean the products so as to avoid damage to the surface

and case.

 After cleaning, make sure that the product is completely dry, otherwise don't use it.

14

7. Accessories Purchase

If you want to purchase the main accessories of the product, please contact the dealer

or call our service hotline at 400-830-7020.

Caution

Please use the accessories specified by o ur company. The consequences
due to any use of unauthorized accessories shall be the responsibility of the
user himself.

15

8. Scope and Duration of Warranty

We promise that the product produced by our company can enjoy the warranty service

under the contract from the date of purchase if there is any occurrence of the defects in

material or manufacturing process under the condition of normal use, operation and

maintenance.

16