Hytera TC-600 Service Manual

－ 1 －

Contents

General………………………………………………………………………………2
Brief Introduction………………………………………………………………….3
Software Specification……………………………………………………………5
Circuit Description……………………………………………………………….11
CPU Pins…………………………………………………………………………...16
Part List 1………………………………………………………………………….18
Adjustment Description…………………………………………………………30
Disassembly and Assembly for Repair……………………………………….33
Exploded View…………………………………………………………………….36
Part List 2…………………………………………………………………………37
Packing…………………………………………………………………………….39
PC Board View……………………………………………………………………40
Block Diagram…………………………………………………………………….42
Schematic Diagram………………………………………………………………43
Specifications…………………………………………………………………….44

TC-600 General

－ 2 －

General

Manual Scope

This manual is intended for use by experienced technicians familiar with similar types of communication
equipment. It contains all service information required for the equipment and is current as of the
publication date.

User Safety Information

The following precautions are recommended for personnel safety:
 DO NOT transmit until all RF connectors are verified secure and any open connectors are properly

terminated.

 SHUT OFF and do not operate this equipment near electrical blasting caps or in an explosive

atmosphere.

 When in vehicles with an airbag, do not place a portable radio in the area over an airbag or in the

airbag deployment area.

 Do not expose the radio to direct sunlight for a long time nor place it close to a heating source.
 Do not use any portable radio with a damaged antenna. If a damaged antenna comes into contact

with your skin, a minor burn may result.

 When transmitting with a portable radio, hold the radio in a vertical position with its microphone

about 5 centimeters away from your mouth.

 If you wear a portable radio on your body, be sure to keep the antenna at least 2.5

centimeters away from your head or body when transmitting.

 This equipment should be serviced by qualified technicians only.

TC-600 Brief Introduction

－ 3 －

Brief Introduction

1. Antenna

Used to transmit/receive signals.

2. LED Indicator

The light will glow red during transmission and glow green during receiving. During transmission,
the light flashes red when the battery voltage is low.

3. Channel Selector Knob

4. Power/Volume Control Knob

Rotate the Power/Volume Knob clockwise until a ―click‖ is heard to turn the radio on, fully counter
clockwise until a ―click‖ is heard to turn the radio off. When the radio is on, turn the knob to adjust
volume.

5. PTT Key

Press and hold PTT key to talk, release to receive.

6. Function Key

The key can be programmed to access the radio features with the preset type of key pressing
through the programming software.

7. Microphone

Used to input sounds.

8. Speaker

Used to output sounds.

TC-600 Brief Introduction

－ 4 －

9. External Jack (for external earphone or radio programming)

Rotate the jack cover and insert accessory plug, or insert programming cable into the jack to
program the radio via programming software.

10. Battery

11. Belt Clip

Used to clip radio on your belt.

12. Battery Latch

Used to fasten and remove the battery.

13. Charging Connector

Insert the battery into the charger; connect the charging connectors with those on the charger to
begin charging.

TC-600 Software Specification

－ 5 －

Software Specification

Radio Feature Description

1. Use Channel Selector Knob to choose from 15+1(Scan) channels

2. Monitor

3. CTCSS/CDCSS Encode & Decode
CTCSS: 38 groups
CDCSS: 83 groups

4. Wideband (25KHz) / Narrowband (12.5KHz)

5. Channel Scan (Priority channel and Revert channel available)

6. Battery Save feature (Dealer programmable)

7. Time-out Timer (TOT)

8. Squelch Level (1-9)

9. Low Battery Alert

10. Programmable Function Key

11. High/Low Power

12. 2-Tone Encode & Decode

13. DTMF ANI

14. Model Set Mode

15. PC Programming & Adjust Mode

16. Manual Adjust Mode

17. User Wired Clone Mode

18. Factory Wired Clone Mode

TC-600 Software Specification

－ 6 －

Radio Modes

Mode

Entry for Mode Startup

Audible & Visual Indicator

User Mode

Disconnect the SELF points and then turn the
power on

Power-on alert tone (one long Beep)

Model Set Mode

Short out the SELF points and then turn the power
on

2 short Beeps, the light flashes from red
to green

User Wired Clone Mode

Disconnect the SELF points, turn on the power
while holding down Function Key, press Function
Key again

1 short Beep

Factory Wired Clone
Mode

Short out the SELF points, turn on the power while
holding down Function Key, press Function Key
again

2 short Beeps

Manual Adjust Mode

Enable Manual Adjust Mode, turn on the power
while holding down [PTT] and Function Key
simultaneously, the radio enters this mode in 2
seconds

2 short Beeps, orange light glows
PC Programming &

Adjust Mode

Connect the radio with PC, turn on the radio and
activate this mode in programming software

1. User Mode

User Mode is for conventional communication operation. Disconnect the two SELF points and then turn
the power on, the radio enters User Mode. (Refer to ―TC-600 Owner’s Manual‖ for detailed operation
description.)

2. Model Set Mode

(1) Select MS1 according to the radio model. If MS1 is 1, short out the two MS1 points on PCB. If not,

disconnect the two MS1 points.
(2) Short out the two SELF points and then turn the power on. Two Beeps sound.
(3) Turn Channel Selector Knob to the corresponding position (1-11) according to the radio model

(Refer to ―Initial Data Table‖).
(4) Press [PTT] while holding down Function Key to set the model. Channel data and settings are

initialized (Refer to ―Initial Data Table‖).

TC-600 Software Specification

－ 7 －

(5) Turn off the power and then disconnect the two SELF points to complete the model setting.

For example, MS1 of TC-600U (450.000~469.995MHz) is 0 and its model is 7(Refer to ―Initial
Data Table‖). To initialize its model and channel data, you can operate as following:

● Disconnect the two MS1 points.

● Short out the two SELF points.

● Turn on the power and rotate the Channel Selector Knob to CH7.

● Press [PTT] while holding down Function Key.

● After reset, turn off the power and disconnect the two SELF points. The radio operates at the

preset frequency after restart.
Note: Once the new model is set, previous channel settings (frequency, CTCSS/CDCSS, channel
function settings) will be deleted, and part of functions are also changed. Therefore, do not make this
operation unless it’s very necessary, such as changing the EEPROM, etc.

3. PC Programming Mode

The following parameters can be set through programming software:
(1) Receive frequency and transmit frequency
(2) Receive signaling and transmit signaling
(3) Busy channel lockout (BCL)
(4) Time-out timer (TOT)
(5) Squelch level
(6) Battery save
(7) Audio alarm
(8) Monitor mode
(9) Scan mode
(10) Scan revert channel
(11) Priority scan channel
(12) Wideband/narrowband per radio
(13) High/low power
(14) Wideband/narrowband per channel

TC-600 Software Specification

－ 8 －

4. PC Adjust Mode

The following settings can be adjusted through the programming software:
(1) Low battery alert level
(2) SQL9
(3) SQL3
(4) CTCSS deviation (wide)
(5) CDCSS deviation (wide)
(6) CTCSS deviation (narrow)
(7) CDCSS deviation (narrow)

5. Manual Adjust Mode

If Manual Adjust Mode is enabled, turn on the power while holding down [PTT] and Function Key
simultaneously, the radio enters Manual Adjust Mode in 2 seconds. Choose the adjusting items by
turning the channel selector knob to CH1-CH7; use [PTT] /Function Key to adjust upwards/downwards
(Note: MIC jack shouldn’t be connected with external cable while adjusting), CH1-CH7 are defined as
follows:
(1) Low battery alert level
(2) SQL9
(3) SQL3
(4) CTCSS deviation (wide)
(5) CDCSS deviation (wide)
(6) CTCSS deviation (narrow)
(7) CDCSS deviation (narrow)

TC-600 Software Specification

－ 9 －

CH12-CH16 are used to adjust transmitter and receiver. Press [PTT] to transmit; release to receive. In
receive mode, short press the Function Key to toggle among high and low power, or long press it to
switch between wideband and narrowband. Three Beeps alternating from high tone to low tone indicate
that the transmit power is switched from high to low; and three beeps alternating from low tone to high
tone indicate that the transmit power is switched from low to high. Two Beeps sound when wideband is
selected and one Beep sounds when narrowband is selected. CH12-ch16 are defined as follows:
(12) Center frequency (the difference between RX and TX frequency is 0.1MHz)
(13) Lowest frequency (the difference between RX and TX frequency is 0.1MHz)
(14) Highest frequency (the difference between RX and TX frequency is –0.075MHz)
(15) Center frequency: transmit DTMF number ―9‖ (the difference between RX and TX frequency is

0.1MHz)

(16) Center frequency: transmit with 250.3Hz CTCSS signaling (the difference between RX and TX

frequency is 0.1MHz)

Note:

To enable/disable the Manual Adjust Mode: short out the two SELF points, turn on the power to enter
Model Set Mode, then Manual Adjust Mode is enabled. Press [PTT] to disable. It suggests this mode be
disabled after the adjustment is completed.

6. User/Factory Wired Clone Mode

The only difference between the two modes is that the latter is able to clone the adjustment settings.
Turn on the power while holding down Function key to enter Wired Clone Mode.
a) If the two SELF points are disconnected, press Function key again, the radio starts user wired clone

and red LED flashes; when cloning is completed, red LED goes out.

b) If the two SELF points are short out, press Function key again, the radio starts factory wired clone

and red LED flashes; when cloning is completed, red LED goes out.

TC-600 Software Specification

－ 10 －

Initial Data Table

MS1

Model

Frequency

(MHz)

IF

(MHz)

1CH (Center)

2CH (Low)

3CH (High)

4CH

5CH

6CH

7CH

8CH

9-16CH

Tx

(MHz)

Rx

(MHz)

Tx

(MHz)

Rx

(MHz)

Tx

(MHz)

Rx

(MHz) (MHz) (MHz) (MHz) (MHz) (MHz) (MHz) 0 1

150.000~173.995

+45.050

162.000

162.100

150.000

150.100

173.975

173.900

162.500

162.550

162.600

162.550

162.650 0 2 136.000~149.995

+45.050

143.000

143.100

136.000

136.100

149.975

149.900

143.500

143.550

143.600

143.550

143.650 0 3 146.000~173.995

+45.050

160.000

160.100

146.000

146.100

173.975

173.900

160.500

160.550

160.600

160.550

160.650 0 4 144.000~147.995

+45.050

146.000

146.100

144.000

144.100

147.975

147.900

146.500

146.550

146.600

146.550

146.650 0 5 136.000~147.995

+45.050

142.000

142.100

136.000

136.100

147.975

147.900

142.500

142.550

142.600

142.550

142.650 0 6 136.000~173.995

+45.050

155.000

155.100

136.000

136.100

173.975

173.900

155.500

155.550

155.600

155.550

155.650 0 7 450.000~469.995

-45.050

460.000

460.100

450.000

450.100

469.975

469.900

460.300

460.350

460.400

460.350

460.450 0 8 400.000~419.995

-45.050

410.000

410.100

400.000

400.100

419.975

419.900

410.500

410.550

410.600

410.550

410.650 0 9 470.000~489.995

-45.050

480.000

480.100

470.000

470.100

489.975

489.900

480.500

480.550

480.600

480.550

480.650

0

10

490.000~511.995

-45.050

501.000

501.100

490.000

490.100

511.975

511.900

501.500

501.550

501.600

501.550

501.650

0

11

220.000~239.995

-45.050

230.000

230.100

220.000

220.100

239.975

239.900

230.500

230.550

230.600

230.550

230.650 1 1 240.000~259.995

-45.050

250.000

250.100

240.000

240.100

259.975

259.900

250.500

250.550

250.600

250.550

250.650 1 2 336.000~367.995

-45.050

352.000

352.100

336.000

336.100

367.975

367.900

352.500

352.550

352.600

352.550

352.650 1 3 368.000~395.995

-45.050

382.000

382.100

368.000

368.100

395.975

395.900

382.500

382.550

382.600

382.550

382.650 1 4 370.000~389.995

-45.050

380.000

380.100

370.000

370.100

389.975

389.900

380.500

380.550

380.600

380.550

380.650 1 5 350.000~369.995

-45.050

360.000

360.100

350.000

350.100

369.975

369.900

360.500

360.550

360.600

360.550

360.650 1 6 406.000~429.995

-45.050

418.000

418.100

406.000

406.100

429.975

429.900

418.500

418.550

418.600

418.550

418.650 1 7 400.000~429.995

-45.050

415.000

415.100

400.000

400.100

429.975

429.900

415.500

415.550

415.600

415.550

415.650 1 8 430.000~439.995

-45.050

435.000

435.100

430.000

430.100

439.975

439.900

435.500

435.550

435.600

435.550

435.650 1 9 438.000~449.995

-45.050

444.000

444.100

438.000

438.100

449.975

449.900

444.500

444.550

444.600

444.550

444.650 1

10

480.000~519.995

-45.050

500.000

500.100

480.000

480.100

519.975

519.900

500.500

500.550

500.600

500.550

500.650

1

11

441.000~451.000

-45.050

446.000

446.100

441.000

441.100

450.975

450.900

446.500

446.550

446.600

446.550

446.650

CH QT/DQT

OFF

OFF

OFF

OFF

OFF

OFF

OFF

023

023

127.3

151.4

TC-600 Circuit Description

－ 11 －

Circuit Description

1. Frequency Configuration

The receiver utilizes double conversion superheterodyne. The first IF is 45.050MHz and the second
is 455 KHz. The first local oscillator signal is supplied from PLL circuit. Frequency needed in the
transmitter is supplied from PLL circuit. Figure 1 shows the frequency configuration.

Frequency Range: 400 MHz—420MHz 450 MHz—470MHz

136 MHz—150MHz 150 MHz—174MHz

Figure 1 Frequency Configuration

2. Receiver

The receiver utilizes double conversion superheterodyne.

1) Front-End RF Amplifier

The input signal from antenna is amplified in RF amplifier (Q27) after passing through the
receive/transmit switch circuit and a 3-stage LC band pass filter. The amplified signals are
filtered by a band pass filter (a 3-stage LC BPF) to eliminate unwanted signals before they
goes to the first mixer.

MCF

45.050MHz

44.595MHz

TC-600 Circuit Description

－ 12 －

Figure 2 Receiver Section Configuration

2) The First Mixer

The signal from RF amplifier is mixed with the first local oscillator signal from PLL frequency
synthesizer in the first mixer (Q23) to generate a 45.050MHz first IF signal. The first IF signal is then
fed through two monolithic crystal filters (XF1) to remove spurious signals from adjacent channels.

3) IF Amplifier

The first IF signal is amplified in Q22 and then enters the IF processing chip IC1. The signal is mixed
with the second local oscillator signal in IC1 to create a 455KHz second IF signal. The second IF
signal is then fed to a 455KHz ceramics filter (CF1) to eliminate unwanted signals before it is amplified
and detected in IC1.

4) AF Amplifier

The demodulated AF signal obtained from IC1 is amplified in IC7 (1/4), and then filtered by low pass
filter Q19 and high pass filter Q20, and then de-emphasized by R130 and C156. The resulting AF
signal passes through a volume control circuit and then is amplified to a sufficient level to drive the
speaker by AF power amplifier (IC8).

5) Squelch

Part of the AF signal from IC1 reenters IC1, and the noise component is amplified and rectified by a
filter and an amplifier to produce a DC voltage corresponding to the noise level. The DC signal goes to
the analog port of the microprocessor (IC11). IC11 determines whether to output sounds from the
speaker by detecting whether the input voltage is higher or lower than the preset value.
To output sounds from the speaker, IC11 sends a high level signal to the MUTE and AFCO lines and
turns on IC8 through Q12.

TC-600 Circuit Description

－ 13 －

DET

FM IF IC1

IF AMP

HPF
AMP

IC7

AF

LPF

HPF

DET

2

39

40

1

SW

Q12

SW

AF/PF AMP

IC7
LPF

IC11
MCU

BUSY

MUTE

AFCO

TI

IC8

SP

Figure 3. AF Amplifier and Squelch Circuit

6) Receive Signaling

CTCSS/CDCSS

Over 300Hz audio frequencies of the signal output from IC1 is cut off by a low pass filter. The resulting
signal enters the microprocessor IC11. IC11 determines whether the CTCSS/CDCSS matches the
preset value, and controls the MUTE, AFCO and the speaker output according to the squelch results.

2-Tone

The output 2-Tone signal from IC1 goes to IC7 (1/4) for voltage amplification, then is processed by
shaping circuit that is comprised of IC7 (2/4) and other components before being detected by IC11 Pin11.
IC11 determines whether the 2-tone matches the preset value, and controls MUTE, APCO and speaker
output according to squelch results.

3. PLL Frequency Synthesizer

PLL circuit generates the first local oscillator signal for reception and the RF signal for transmission.

1) PLL

The step frequency of PLL circuit is 5KHz\6.25KHz\12.5 KHz\10 KHz. A 12.8MHz reference
oscillator signal is divided at IC2 by a fixed counter to produce a 5 KHz\6.25KHz\12.5 KHz\10
KHz reference frequency. The output signal from voltage control oscillator (VCO) passes
through buffer amplifier Q14 and is divided at IC2 by the programmable dual-module counter.
The divided signal is compared in the phase comparator IC2 with the 5 KHz\6.25KHz\12.5 KHz\25
KHz reference signal. The output signal from phase comparator is filtered by a low-pass filter
and passed to the VCO to control the oscillator frequency. (See Figure 4)

TC-600 Circuit Description

－ 14 －

Figure 4 PLL Circuit

2) VCO

The operation frequency is generated by Q16 in transmit mode and by Q8 in receive mode.
The operation frequency generates a control voltage through the phase comparator to control
the varactor diodes, so that the oscillator frequency is made consistent with the preset
frequency in CPU (D2 and D3 in transmit mode, D7 and D8 in receive mode). In receive mode,
Q6 turns off Q16 and turns Q7 on, which causes the T/R pin to be set high. The T/R pin is set low in
transmit mode. The output from Q8 and Q16 is amplified by Q14 and sent to the buffer amplifier.

4. Transmitter

1) Transmit Audio

The modulation signal from microphone is amplified by IC3, pre-emphasized, then filtered by another
low pass filter（separate filter）(Q25 and Q24) to eliminate the frequencies higher than 3KHz. The
resulting signal enters the VCO for direct FM modulation. The voice voltage amplitude control circuit
（Q46\R131\R601） is used to switch between wideband and narrowband. (See Figure 5)

2) CTCSS/CDCSS Encoder

The signal needed by CTCSS/CDCSS encoder is generated by IC11 and FM-modulated to the PLL
reference signal. Since the reference OSC does not modulate the loop characteristic frequency or
higher, modulation is performed at the VCO side by splitter. (See Figure 5)

Figure 5 Transmit CTCSS

TC-600 Circuit Description

－ 15 －

3) DTMF/2-Tone Encoder

DTMF/2-Tone signalings are generated by IC11 and outputted in parallel by Pin 48-51. The output signal
is reshaped by resistor array CP7-CP10, then sent to IC3 (1/4) for amplification, and filtered by active
LPF consisting of Q25, Q24 and other components to eliminate the corresponding HF emission before
being passed to TX VCO for modulation. The modulated signal is applied to AF AMP through C254 for
ease of monitoring.

4) RF Amplifier

The transmit signal obtained from VCO buffer amplifier Q14 is amplified by Q15 and Q17. The amplified
signal is passed to power amplifier Q32 and Q31, and is capable of generating a 4.0W RF power. Q50
and R617 are used to toggle between high and low power.

5) Antenna Switch and LPF

The output signal from RF amplifier is passed through a low-pass filter network and a transmit/receive
switch circuit before reaching the antenna terminal. The transmit/receive switch circuit is comprised of
D11 and D12. D11 and D12 is turned on (conductive) in transmit mode and off (isolated) in receive
mode.

5. Power

The 5V reference power supply for the control circuit is derived from a LDO IC. The reference power
provides a 5V voltage in transmit mode [T_V], a 5V voltage in receive mode [R_V], and a 5V voltage
shared in both modes based on the control signal from the microprocessor.

6. Control System

The IC11 CPU operates at 7.3728MHz.

TC-600 CPU Pins

－ 16 －

CPU Pins

PIN No.

PIN NAME

I/O

DESCRIPTION

1

TI I CTCSS/CDCSS input

2

BUSY I Busy signal input

3

BATT I Battery voltage detect

4

TIBI I CTCSS/CDCSS external circuit center point input

5

NC

6

SAVE O Battery save control H: OFF L: ON

7

TXLow

O

TX power control H: Low power L: High power

8

LE 0 PLL IC enable

9

PLL_DAT

O

PLL data output

10

PLL_CLK

O

PLL clock output

11

TTSin I 2-Tone input

12

BEEP O BEEP output

13

SCL O E2PROM clock line

14

SDA

I/O

E2PROM data line

15

MUTE

O

MIC mute control H: MIC mute L: MIC enable

16

MS1 O Model select

17

GLED O Green light control H: Lit

18

RLED

O

Red light control H: Lit

19

TXD O RS-232C output

20

RXD I RS-233C input

21

PTT I PTT key input L: Press

22

NC I

23

RXC O Receiver power supply control L: ON

24

NC I NC

25

RESET

I

Reset input

26

SELF I Self programming L: ON

27

TXC O Transmitter power supply control H: ON

28

Xin I

Oscillator input

29

Xout O

Oscillator output

30

Vss I GND

31

RT O RX/TX control H: RX L: TX

32

UL I PLL unlock detect H: Lock L: Unlock

33

IF_CTRL

I

IF select H: 21.4MHz L: 45.05MHz

34

MONI I Function key input L: Press

35

ENC0

I

Channel Selector Knob encode input

36

ENC1 I 37

ENC2 I 38

ENC3

I

TC-600 CPU Pins

－ 17 －

39

AF_MUTE

O

AF mute control

40

AF_PWR

O

AF power supply control

41

CTDCSS5

O

CTCSS/CDCSS code output

42

CTDCSS4

O

43

CTDCSS3

O

44

CTDCSS2

O

45

CTDCSS1

O

46

CTDCSS0

O

47

WNTC

O

Wideband/narrowband L: W H: N

48

DTMF/2ToneOut5

0

DTMF/2-Tone code output

49

DTMF/2ToneOut4

0

50

DTMF/2ToneOut3

0

51

DTMF/2ToneOut2

0

52

DTMF/2ToneOut1

0

53

DTMF/2ToneOut0

0

54-70

NC

71

Vcc I Power input: 5V

72

Vref I

A-D conversion reference voltage

73

Avss

I

A-D GND

74-80

NC

TC-600 Part List 1

－ 18 －

Part List 1

No. Material No. Material Name Description Qty. Ref.No. Print No. Remarks

1 01020002 Resistor0402

0Ω 　J

1 R623 B2e

2 01020002 Resistor0402

0Ω 　J

1 C251 B3e

3 01030002 Resistor0603

0Ω 　J

1 L9 B3b

4 01030002 Resistor0603

0Ω 　J

1 R107 B3B

5 01030002 Resistor0603

0Ω 　J

1 R128 B3B

6 01030002 Resistor0603

0Ω 　J

1 R108 B3E

7 01030002 Resistor0603

0Ω 　J

1 C23 B3F

8 01030002 Resistor0603

0Ω 　J

1 R194 B3F

9 01030002 Resistor0603

0Ω 　J

1 R111 B4E

10 01030002 Resistor0603

0Ω 　J

1 R197 B4F

11 01030002 Resistor0603

0Ω 　J

1 R508 B5B

12 01030002 Resistor0603

0Ω 　J

1 R151 B5E

13 01030002 Resistor0603

0Ω 　J

1 R150 B5F

14 01030002 Resistor0603

0Ω 　J

1 D20 T1D

15 01030002 Resistor0603

0Ω 　J

1 R116 T3B

16 01030002 Resistor0603

0Ω 　J

1 R106 T3F

17 01030002 Resistor0603

0Ω 　J

1 R110 T4G

18 01031002 Resistor0603

10Ω 　J

1 R164 B2C

19 01031002 Resistor0603

10Ω 　J

1 R80 B2D

20 01031002 Resistor0603

10Ω 　J

1 R196 B4G

21 01031002 Resistor0603

10Ω 　J

1 R82 B4G

22 01031002 Resistor0603

10Ω 　J

1 R113 T5J

23 01031012 Resistor0603

100Ω 　J

1 R74 B2C

24 01031012 Resistor0603

100Ω 　J

1 R147 B4E

25 01031012 Resistor0603

100Ω 　J

1 R75 B4J

26 01031012 Resistor0603

100Ω 　J

1 R76 B5E

27 01031012 Resistor0603

100Ω 　J

1 R127 B5F

28 01031012 Resistor0603

100Ω 　J

1 R90 T5H

29 01031022 Resistor0603

1KΩ 　J

1 R63 B4u

30 01031022 Resistor0603

1KΩ 　J

1 R114 B1B

31 01031022 Resistor0603

1KΩ 　J

1 R51 B1F

32 01031022 Resistor0603

1KΩ 　J

1 R210 b1g

33 01031022 Resistor0603

1KΩ 　J

1 R56 B2B

34 01031022 Resistor0603

1KΩ 　J

1 R53 B2D

35 01031022 Resistor0603

1KΩ 　J

1 R118 B2I

36 01031022 Resistor0603

1KΩ 　J

1 R39 B3B

37 01031022 Resistor0603

1KΩ 　J

1 R218 b3c

38 01031022 Resistor0603

1KΩ 　J

1 R57 B5B

39 01031022 Resistor0603

1KΩ 　J

1 R4 T2B

40 01031022 Resistor0603

1KΩ 　J

1 R60 T2D

41 01031022 Resistor0603

1KΩ 　J

1 R61 T2D

42 01031022 Resistor0603

1KΩ 　J

1 R59 T3B

TC-600 Part List 1

－ 19 －

No. Material No. Material Name Description Qty. Ref.No. Print No. Remarks

43 01031022 Resistor0603

1KΩ 　J

1 R52 T3F

44 01031022 Resistor0603

1KΩ 　J

1 R58 T4B

45 01031022 Resistor0603

1KΩ 　J

1 R89 T4I

46 01031232 Resistor0603

12KΩ 　J

1 R170 B1D

47 01031032 Resistor0603

10KΩ 　J

1 R119 B2A

48 01031032 Resistor0603

10KΩ 　J

1 R38 B2A

49 01031032 Resistor0603 100K J 1 R17 B2F

50 01031032 Resistor0603

10KΩ 　J

1 R44 B2I

51 01031032 Resistor0603

10KΩ 　J

1 R45 B2I

52 01031032 Resistor0603

10KΩ 　J

1 R212 b3b

53 01031032 Resistor0603

10KΩ 　J

1 R213 b3c

54 01031032 Resistor0603

10KΩ 　J

1 R40 B3F

55 01031032 Resistor0603

10KΩ 　J

1 R211 b4b

56 01031032 Resistor0603

10KΩ 　J

1 R37 T2E

57 01031232 Resistor0603

12KΩ 　J

1 R204 T2G

58 01031032 Resistor0603

10KΩ 　J

1 R100 T4B

59 01031032 Resistor0603

10KΩ 　J

1 R42 T5E

60 01031032 Resistor0603

10KΩ 　J

1 R41 T5F

61 01031042 Resistor0603

100KΩ 　J

1 R9 B1D

62 01031042 Resistor0603

100KΩ 　J

1 R202 B2B

63 01031042 Resistor0603

100KΩ 　J

1 R8 B2E

64 01031042 Resistor0603

100KΩ 　J

1 R13 B3D

65 01031042 Resistor0603

100KΩ 　J

1 R15 B3D

66 01031042 Resistor0603

100KΩ 　J

1 R12 B4B

67 01031042 Resistor0603

100KΩ 　J

1 R36 B4B

68 01031042 Resistor0603

100KΩ 　J

1 R10 B4C

69 01031042 Resistor0603

100KΩ 　J

1 R7 B5B

70 01031042 Resistor0603

100KΩ 　J

1 R175 T1B

71 01031042 Resistor0603

100KΩ 　J

1 R176 T2B

72 01031042 Resistor0603

100KΩ 　J

1 R35 T2C

73 01031042 Resistor0603

100KΩ 　J

1 R18 T4B

74 01031042 Resistor0603

100KΩ 　J

1 R145 T5F

75 01031052 Resistor0603

1.0MΩ 　J

1 R109 T2B

76 01031242 Resistor0603

120KΩ 　J

1 R11 B2B

77 01031242 Resistor0603

120KΩ 　J

1 R72 B2D

78 01031242 Resistor0603

120KΩ 　J

1 R124 T3F

79 01031512 Resistor0603

150Ω 　J

1 R69 B2C

80 01031512 Resistor0603

150Ω 　J

1 R68 B2E

81 01031012 Resistor0603

100Ω 　J

1 r616 T3E

82 01031522 Resistor0603

1.5KΩ 　J

1 R48 B3E

83 01031522 Resistor0603

1.5KΩ 　J

1 R47 B4c

84 01031522 Resistor0603

1.5KΩ 　J

1 r619 b4d

85 01031522 Resistor0603

1.5KΩ 　J

1 R203 T2E

86 01031522 Resistor0603

1.5KΩ 　J

1 R55 T2E

87 01031522 Resistor0603

1.5KΩ 　J

1 R50 T5F

88 01031532 Resistor0603

15KΩ 　J

1 R161 T4F

TC-600 Part List 1

－ 20 －

No. Material No. Material Name Description Qty. Ref.No. Print No. Remarks

89 01031532 Resistor0603

15KΩ 　J

1 R163 T4F

90 01031532 Resistor0603

15KΩ 　J

1 R162 T4G

91 01031542 Resistor0603

150KΩ 　J

1 R14 B3D

92 01031542 Resistor0603

150KΩ 　J

1 R140 B4A

93 01031542 Resistor0603

150KΩ 　J

1 R141 B4A

94 01031542 Resistor0603

150KΩ 　J

1 R142 B4A

95 01031542 Resistor0603

150KΩ 　J

1 R139 B4A

96 01031822 Resistor0603

1.8KΩ 　J

1 R144 B3C

97 01031822 Resistor0603

1.8KΩ 　J

1 R131 T4E

98 01031852 Resistor0603

1.8MΩ 　J

1 R156 T5F

99 01031852 Resistor0603

1.8MΩ 　J

1 R155 T5G

100 01032032 Resistor0603

20KΩ 　J

1 R98 B3D

101 01032212 Resistor0603

220Ω 　J

1 R67 B2D

102 01032222 Resistor0603

2.2KΩ 　J

1 R209 b1g

103 01032222 Resistor0603

2.2KΩ 　J

1 R115 B2A

104 01032222 Resistor0603

2.2KΩ 　J

1 R3 B4B

105 01032222 Resistor0603

2.2KΩ 　J

1 R149 B4E

106 01032222 Resistor0603

2.2KΩ 　J

1 R165 B4F

107 01032222 Resistor0603

2.2KΩ 　J

1 R6 T2B

108 01032222 Resistor0603

2.2KΩ 　J

1 R174 T4H

109 01032232 Resistor0603

22KΩ 　J

1 R120 T4G

110 01032242 Resistor0603

220KΩ 　J

1 R192 B4E

111 01032242 Resistor0603

220KΩ 　J

1 R167 T1D

112 01032722 Resistor0603

2.7KΩ 　J

1 R64 B2G

113 01032722 Resistor0603

2.7KΩ 　J

1 R65 B2G

114 01032722 Resistor0603

2.7KΩ 　J

1 R49 B4D

115 01032731 Resistor0603

27KΩ 　D

1 R102 B3H

116 01033931 Resistor0603

39KΩ 　D

1 r617 T2G

117 01035122 Resistor0603

5.1KΩ 　J

1 r299 B5g

118 01032732 Resistor0603

27KΩ 　J

1 R132 B3C

119 01030002 Resistor0603

0Ω 　 J

1 R602 B3C

120 01032742 Resistor0603

270KΩ 　J

1 R16 B3D

121 01032742 Resistor0603

270KΩ 　J

1 R2 B3d

122 01033022 Resistor0603

3KΩ 　J

1 R81 B3F

123 01033312 Resistor0603

330Ω 　J　RCT03331JTP

1 R62 B2I

124 01033312 Resistor0603

330Ω 　J　RCT03331JTP

1 R146 B4D

125 01033322 Resistor0603

3.3KΩ 　J

1 R601 B1E

126 01033322 Resistor0603

3.3KΩ 　J

1 R28 B1F

127 01033322 Resistor0603

3.3KΩ 　J

1 R29 B2D

128 01033322 Resistor0603

3.3KΩ 　J

1 R34 B2D

129 01033322 Resistor0603

3.3KΩ 　J

1 R30 B2E

130 01033322 Resistor0603

3.3KΩ 　J

1 R27 B2F

131 01033322 Resistor0603

3.3KΩ 　J

1 R31 B3G

132 01033322 Resistor0603

3.3KΩ 　J

1 R135 B4a

133 01033322 Resistor0603

3.3KΩ 　J

1 R136 B4A

134 01033322 Resistor0603

3.3KΩ 　J

1 R137 B4B

TC-600 Part List 1

－ 21 －

No. Material No. Material Name Description Qty. Ref.No. Print No. Remarks

135 01033322 Resistor0603

3.3KΩ 　J

1 R25 B4B

136 01033322 Resistor0603

3.3KΩ 　J

1 R26 B4c

137 01033322 Resistor0603

3.3KΩ 　J

1 R138 B5A

138 01033322 Resistor0603

3.3KΩ 　J

1 R32 B5E

139 01033322 Resistor0603

3.3KΩ 　J

1 R33 T5F

140 01033332 Resistor0603

33KΩ 　J RCT03333J

1 R215 b4c

141 01033332 Resistor0603

33KΩ 　J RCT03333J

1 R24 T2G

142 01033342 Resistor0603

330KΩ 　J

1 R43 T2A

143 01033022 Resistor0603

3KΩ 　J

1 R117 B2B

144 01032731 Resistor0603

27KΩ 　D

1 R104 B3H

145 01033932 Resistor0603

39KΩ 　J

1 R159 T5E

146 01033932 Resistor0603

39KΩ 　J

1 R152 T5F

147 01033932 Resistor0603

39KΩ 　J

1 R153 T5F

148 01033932 Resistor0603

39KΩ 　J

1 R158 T5F

149 01034702 Resistor0603

47Ω 　J

1 R191 B2B

150 01034702 Resistor0603

47Ω 　J

1 R123 B3G

151 01034702 Resistor0603

47Ω 　J

1 R125 B3H

152 01034712 Resistor0603

470Ω 　J

1 R166 B4F

153 01034722 Resistor0603

4.7KΩ 　J

1 R84 B2C

154 01034722 Resistor0603

4.7KΩ 　J

1 R95 B3B

155 01034722 Resistor0603

4.7KΩ 　J

1 R87 T1A

156 01034722 Resistor0603

4.7KΩ 　J

1 R121 T1B

157 01034722 Resistor0603

4.7KΩ 　J

1 R99 T1B

158 01034722 Resistor0603

4.7KΩ 　J

1 R88 T1C

159 01034722 Resistor0603

4.7KΩ 　J

1 R177 T2A

160 01034722 Resistor0603

4.7KΩ 　J

1 r208 T3a

161 01034722 Resistor0603

4.7KΩ 　J

1 r206 T4A

162 01034722 Resistor0603

4.7KΩ 　J

1 r207 T4A

163 01034732 Resistor0603

47KΩ 　J

1 r143 B4u

164 01034732 Resistor0603

47KΩ 　J

1 R105 B1E

165 01034732 Resistor0603

47KΩ 　J

1 R96 B2B

166 01034732 Resistor0603

47KΩ 　J

1 R615 b3b

167 01034732 Resistor0603

47KΩ 　J

1 R214 b3c

168 01034732 Resistor0603

47KΩ 　J

1 R217 b3c

169 01034732 Resistor0603

47KΩ 　J

1 R103 B4G

170 01034732 Resistor0603

47KΩ 　J

1 R4 T2B

171 01034732 Resistor0603

47KΩ 　J

1 R610 T2C

172 01034732 Resistor0603

47KΩ 　J

1 R93 T2F

173 01034732 Resistor0603

47KΩ 　J

1 R54 T3G

174 01034732 Resistor0603

47KΩ 　J

1 R606 T3I

175 01034732 Resistor0603

47KΩ 　J

1 R607 T3I

176 01034732 Resistor0603

47KΩ 　J

1 R608 T3I

177 01034732 Resistor0603

47KΩ 　J

1 R609 T3I

178 01034732 Resistor0603

47KΩ 　J

1 R154 T4F

179 01034742 Resistor0603

470KΩ J

1 R22 T1D

180 01034742 Resistor0603

470KΩ J

1 R94 T2F

TC-600 Part List 1

－ 22 －

No. Material No. Material Name Description Qty. Ref.No. Print No. Remarks

181 01034732 Resistor0603

47KΩ 　J

1 R101 B4H

182 01035612 Resistor0603

560Ω 　J

1 R5 B4E

183 01035621 Resistor0603

5.6KΩ 　D

1 R216 b3c

184 01035622 Resistor0603

5.6KΩ 　J

1 R79 B2D

185 01035622 Resistor0603

5.6KΩ 　J

1 R130 B4B

186 01035632 Resistor0603

56KΩ 　J

1 R157 T4F

187 01035642 Resistor0603

560KΩ 　J

1 R148 B4D

188 01036812 Resistor0603

680Ω 　J

1 R70 B3F

189 01036822 Resistor0603

6.8KΩ 　J

1 R169 B1D

190 01036822 Resistor0603

6.8KΩ 　J

1 R85 T4F

191 01036832 Resistor0603

68KΩ 　J

1 R200 B2B

192 01036832 Resistor0603

68KΩ 　J

1 R198 T4E

193 01036842 Resistor0603

680KΩ 　 J

1 R134 B3C

194 01036842 Resistor0603

680KΩ 　 J

1 R219 b3c

195 01036842 Resistor0603

680KΩ 　 J

1 R1 B4B

196 01037542 Resistor0603

750KΩ 　J

1 R160 T4G

197 01038202 Resistor0603

82Ω 　J

1 R171 B1D

198 01038212 Resistor0603

820Ω 　J RCT03821JTP

1 R66 B1F

199 01038232 Resistor0603

82KΩ 　J

1 R97 B3C

200 01038232 Resistor0603

82KΩ 　J

1 R133 T2C

201 01050002 Resistor0805

0Ω 　J

1 L3 B3H

202 01060002 Resistor1206

0Ω 　J

1 R172 T2H

203 01060002 Resistor1206

0Ω 　J

1 R77 T2H

204 01060002 Resistor1206

0Ω 　J

1 R173 T2I

205 0122473H Variable resistor

47KΩ

1 VR2 T5E

206 0122683H Variable resistor

68KΩ

1 VR4 T1B

207 0122683H Variable resistor

68KΩ

1 VR3 T4E

208 012D103A Resistor array

10KΩ

1 CP5 T1B

209 012D103A Resistor array

10KΩ

1 cp8 T4B

210 012D472A Resistor array

4.7KΩ

1 CP4 T1B

211 012D472A Resistor array

4.7KΩ

1 cp10 T4A

212 014D103A Resistor array

10KΩ

1 CP1 T1B

213 014D103A Resistor array

10KΩ

1 CP6 T4A

214 014D103A Resistor array

10KΩ

1 cp7 T4B

215 014D472A Resistor array

4.7KΩ

1 CP3 T1B

216 014D472A Resistor array

4.7KΩ

1 cp3 T1B

217 014D472A Resistor array

4.7KΩ

1 cp9 T4A

218 02020100 Capacitor0402

1P　C　50V

1 C95 B1E

219 0205R753 Capacitor0805

0.75P　C　50V

1 C140 B4I

220 02020100 Capacitor0402

1P　C　50V

1 C146 B4J

221 02020200 Capacitor0402

2P　C　50V

1 C192 B1D

222 02020200 Capacitor0402

2P　C　50V

1 C195 B2B

223 02020200 Capacitor0402

2P　C　50V

1 C143 B4I

224 0202030B Capacitor0402

3P　B　50V

1 C103 B2B

225 0202030B Capacitor0402

3P　B　50V

1 C105 B4G

226 0202050B Capacitor0402

5P　B　50V

1 C142 B4I

TC-600 Part List 1

－ 23 －

No. Material No. Material Name Description Qty. Ref.No. Print No. Remarks

227 0202040B Capacitor0402

4P　B　50V

1 C141 B4I

228 02020400 Capacitor0402

4P　C　50V

1 C134 B5H

229 0202040B Capacitor0402

4P　B　50V

1 C186 B2C

230 0202040B Capacitor0402

4P　B　50V

1 C89 B4I

231 0202070B Capacitor0402

7P　B　50V

1 C189 B2C

232 0202040B Capacitor0402

4P　B　50V

1 C136 B4H

233 0202050B Capacitor0402

5P　B　50V

1 C101 B4I

234 0202060B Capacitor0402

6P　B　50V

1 C145 B4J

235 02020701 Capacitor0402

7P　D　50V

1 C182 B1D

236 02020601 Capacitor0402

6P　D　50V

1 C96 B2D

237 02020601 Capacitor0402

6P　D　50V

1 C97 B2E

238 02020601 Capacitor0402

6P　D　50V

1 C98 B3G

239 02020601 Capacitor0402

6P　D　50V

1 C106 B5E

240 02020601 Capacitor0402

6P　D　50V

1 C108 B5E

241 02020701 Capacitor0402

7P　D　50V

1 C90 B1E

242 02020701 Capacitor0402

7P　D　50V

1 C193 B1D

243 0202050B Capacitor0402

5P　B　50V

1 C139 B4I

244 02020R50 Capacitor0402

0.5P　C　50V

1 C91 B2D

245 02020R50 Capacitor0402

0.5P　C　50V

1 C93 B4E

246 02020R50 Capacitor0402

0.5P　C　50V

1 C94 B4E

247 02020R50 Capacitor0402

0.5P　C　50V

1 C163 B4F

248 02020R50 Capacitor0402

0.5P　C　50V

1 C164 B4G

249 02021001 Capacitor0402

10P　D　50V

1 C187 B2C

250 02021001 Capacitor0402

10P　D　50V

1 C88 B2E

251 02021001 Capacitor0402

10P　D　50V

1 C130 B3A

252 0202030B Capacitor0402

3P　B　50V

1 C135 B3F

253 02021001 Capacitor0402

10P　D　50V

1 C144 T4F

254 02021012 Capacitor0402

100P　J　50V

1 C15 B2A

255 02021012 Capacitor0402

100P　J　50V

1 C16 B2A

256 02021012 Capacitor0402

100P　J　50V

1 C17 B2A

257 02021043 Capacitor0402

0.1uF　K　10V

1 C180 B2A

258 02021012 Capacitor0402

100P　J　50V

1 C131 B2B

259 02021012 Capacitor0402

100P　J　50V

1 C132 B2D

260 02021012 Capacitor0402

100P　J　50V

1 c213 b3c

261 02021012 Capacitor0402

100P　J　50V

1 C179 B3d

262 02021012 Capacitor0402

100P　J　50V

1 c212 b4c

263 02021023 Capacitor0402

1000P　K　50V

1 C65 B1C

264 02021023 Capacitor0402

1000P　K　50V

1 C59 B1G

265 02021023 Capacitor0402

1000P　K　50V

1 C60 B1G

266 02021023 Capacitor0402

1000P　K　50V

1 C113 B2B

267 02021023 Capacitor0402

1000P　K　50V

1 C109 B2C

268 02021023 Capacitor0402

1000P　K　50V

1 C110 B2C

269 02021023 Capacitor0402

1000P　K　50V

1 C121 B2E

270 02021023 Capacitor0402

1000P　K　50V

1 C61 B2G

271 02021023 Capacitor0402

1000P　K　50V

1 C62 B2G

272 02021023 Capacitor0402

1000P　K　50V

1 C82 B2I

TC-600 Part List 1

－ 24 －

No. Material No. Material Name Description Qty. Ref.No. Print No. Remarks

273 02021023 Capacitor0402

1000P　K　50V

1 C83 B2I

274 02021023 Capacitor0402

1000P　K　50V

1 C69 B3b

275 02021023 Capacitor0402

1000P　K　50V

1 C73 B3E

276 02021023 Capacitor0402

1000P　K　50V

1 C114 B3H

277 02021023 Capacitor0402

1000P　K　50V

1 C68 B3H

278 02021023 Capacitor0402

1000P　K　50V

1 C70 B4A

279 02021023 Capacitor0402

1000P　K　50V

1 C74 B4E

280 02021023 Capacitor0402

1000P　K　50V

1 C111 B4H

281 02021023 Capacitor0402

1000P　K　50V

1 C71 B5B

282 02021023 Capacitor0402

1000P　K　50V

1 C81 T1C

283 02021023 Capacitor0402

1000P　K　50V

1 C80 T1D

284 02021023 Capacitor0402

1000P　K　50V

1 C66 T1E

285 02021023 Capacitor0402

1000P　K　50V

1 C79 T1E

286 02021023 Capacitor0402

1000P　K　50V

1 C78 T2D

287 02021023 Capacitor0402

1000P　K　50V

1 C75 T4F

288 02021023 Capacitor0402

1000P　K　50V

1 C198 T4G

289 02021023 Capacitor0402

1000P　K　50V

1 C76 T4G

290 02021023 Capacitor0402

1000P　K　50V

1 C77 T4G

291 02021043 Capacitor0402

0.1uF　K　10V

1 C123 B1B

292 02021033 Capacitor0402

0.01uF　K　16V

1 C5 B1F

293 02021033 Capacitor0402

0.01uF　K　16V

1 C7 B2C

294 02021033 Capacitor0402

0.01uF　K　16V

1 c209 b3b

295 02021033 Capacitor0402

0.01uF　K　16V

1 c210 b3b

296 02021033 Capacitor0402

0.01uF　K　16V

1 C12 B3I

297 02021033 Capacitor0402

0.01uF　K　16V

1 C8 B4A

298 02021033 Capacitor0402

0.01uF　K　16V

1 C2 B4B

299 02021033 Capacitor0402

0.01uF　K　16V

1 C3 B4B

300 02021033 Capacitor0402

0.01uF　K　16V

1 C4 B4C

301 02021033 Capacitor0402

0.01uF　K　16V

1 C11 T1B

302 02021033 Capacitor0402

0.01uF　K　16V

1 C137 T2I

303 02021033 Capacitor0402

0.01uF　K　16V

1 c252 T3a

304 02021033 Capacitor0402

0.01uF　K　16V

1 c253 T3a

305 02021033 Capacitor0402

0.01uF　K　16V

1 C241 T3J

306 02021033 Capacitor0402

0.01uF　K　16V

1 C242 T3J

307 02021033 Capacitor0402

0.01uF　K　16V

1 C240 T4J

308 02021033 Capacitor0402

0.01uF　K　16V

1 C243 T4J

309 02021033 Capacitor0402

0.01uF　K　16V

1 C10 T5F

310 02021033 Capacitor0402

0.01uF　K　16V

1 C9 T5F

311 02021043 Capacitor0402

0.1uF　K　10V

1 c211 b3b

312 02021043 Capacitor0402

0.1uF　K　10V

1 C43 B3C

313 02021043 Capacitor0402

0.1uF　K　10V

1 C46 B3C

314 02021043 Capacitor0402

0.1uF　K　10V

1 C51 B3I

315 02021043 Capacitor0402

0.1uF　K　10V

1 C37 B4B

316 02023333 Capacitor0402

0.033uF　K　16V

1 C44 B4B

317 02021043 Capacitor0402

0.1uF　K　10V

1 C38 B4C

318 02021043 Capacitor0402

0.1uF　K　10V

1 C39 B4D

TC-600 Part List 1

－ 25 －

No. Material No. Material Name Description Qty. Ref.No. Print No. Remarks

319 02021043 Capacitor0402

0.1uF　K　10V

1 C233 B4E

320 02021043 Capacitor0402

0.1uF　K　10V

1 C45 B5B

321 02021043 Capacitor0402

0.1uF　K　10V

1 C178 T2B

322 02021043 Capacitor0402

0.1uF　K　10V

1 C84 T2E

323 02021043 Capacitor0402

0.1uF　K　10V

1 C40 T2F

324 02021043 Capacitor0402

0.1uF　K　10V

1 C64 T2F

325 02021043 Capacitor0402

0.1uF　K　10V

1 C250 T3E

326 02021043 Capacitor0402

0.1uF　K　10V

1 C49 T4G

327 02021043 Capacitor0402

0.1uF　K　10V

1 C50 T4G

328 02021833 Capacitor0402 0.018UF 16V K. 1 C156 B5B

329 02021R5B Capacitor0402

1.5P　B　50V

1 C196 B3E

330 02022002 Capacitor0402

20PF　UMK105CG200JW-F

1 C506 B3I

331 02022202 Capacitor0402

22P　J　50V

1 C188 B1C

332 02022202 Capacitor0402

22P　J　50V

1 C100 B2D

333 02022212 Capacitor0402

220P　J　50V

1 C67 B3H

334 02022212 Capacitor0402

220P　J　50V

1 C13 B4B

335 02022212 Capacitor0402

220P　J　50V

1 C14 B4B

336 02022212 Capacitor0402

220P　J　50V

1 C239 T5I

337 02022233 Capacitor0402

0.022uF　K　16V

1 C170 T1B

338 02022233 Capacitor0402

0.022uF　K　16V

1 C168 T4G

339 02022233 Capacitor0402

0.022uF　K　16V

1 C169 T4G

340 02022233 Capacitor0402

0.022uF　K　16V

1 C167 T5F

341 02022702 Capacitor0402

27P　J　50V

1 C138 B3H

342 02022702 Capacitor0402

27P　J　50V

1 C18 B5B

343 02022723 Capacitor0402

2700P　K　50V

1 C172 T5F

344 02023302 Capacitor0402

33P　J　50V

1 C55 B3I

345 02023302 Capacitor0402

33P　J　50V

1 C52 B4B

346 02023302 Capacitor0402

33P　J　50V

1 C53 B4B

347 02023302 Capacitor0402

33P　J　50V

1 C54 B4C

348 02023302 Capacitor0402

33P　J　50V

1 C175 T2B

349 02023302 Capacitor0402

33P　J　50V

1 C176 T3B

350 02023323 Capacitor0402

3300P　K　50V

1 C166 T5F

351 02023333 Capacitor0402

0.033uF　K　16V

1 C160 B3D

352 02023333 Capacitor0402

0.033uF　K　16V

1 C151 B4A

353 02023333 Capacitor0402

0.033uF　K　16V

1 C150 B4B

354 02023333 Capacitor0402

0.033uF　K　16V

1 C152 B4B

355 02023333 Capacitor0402

0.033uF　K　16V

1 C153 B4B

356 02023333 Capacitor0402

0.033uF　K　16V

1 c255 T4A

357 02023343 Capacitor0402 0.33uF 1 C127 B1A

358 02023343 Capacitor0402 0.33uF 1 C126 B1B

359 02023343 Capacitor0402 0.33uF 1 C133 B4G

360 02023902 Capacitor0402

39P　J　50V

1 C128 B2A

361 02023923 Capacitor0402

3900P　K　25V

1 C181 T2C

362 02023933 Capacitor0402

0.039uF　K　10V

1 C122 T2E

363 02024702 Capacitor0402

47P　J　50V

1 C129 B2A

364 02024713 Capacitor0402

470P　K　50V

1 C231 B1C

TC-600 Part List 1

－ 26 －

No. Material No. Material Name Description Qty. Ref.No. Print No. Remarks

365 02024713 Capacitor0402

470P　K　50V

1 C25 B2B

366 02024713 Capacitor0402

470P　K　50V

1 C26 B2B

367 02024713 Capacitor0402

470P　K　50V

1 C22 B2D

368 02024713 Capacitor0402

470P　K　50V

1 C31 B2D

369 02024713 Capacitor0402

470P　K　50V

1 C21 B2E

370 02024713 Capacitor0402

470P　K　50V

1 C149 B2G

371 02024713 Capacitor0402

470P　K　50V

1 C197 B3B

372 02024713 Capacitor0402

470P　K　50V

1 C207 B3F

373 02024713 Capacitor0402

470P　K　50V

1 C27 B3G

374 02024713 Capacitor0402

470P　K　50V

1 C29 B3I

375 02024713 Capacitor0402

470P　K　50V

1 C36 B4E

376 02024713 Capacitor0402

470P　K　50V

1 C204 B4F

377 02024713 Capacitor0402

470P　K　50V

1 C35 B4F

378 02024713 Capacitor0402

470P　K　50V

1 C24 B4G

379 02023302 Capacitor0402

33P　J　50V

1 C42 B4G

380 02024713 Capacitor0402

470P　K　50V

1 C28 B4H

381 02024713 Capacitor0402

470P　K　50V

1 C30 B4I

382 02024713 Capacitor0402

470P　K　50V

1 C208 B4J

383 02024713 Capacitor0402

470P　K　50V

1 C20 B5B

384 02024713 Capacitor0402

470P　K　50V

1 C32 B5E

385 02024713 Capacitor0402

470P　K　50V

1 C33 B5F

386 02024713 Capacitor0402

470P　K　50V

1 c257 T2G

387 02024713 Capacitor0402

470P　K　50V

1 C171 T5F

388 02024713 Capacitor0402

470P　K　50V

1 C34 T5G

389 02024723 Capacitor0402

4700P　K　50V

1 C57 B4c

390 02024723 Capacitor0402

4700P　K　50V

1 C232 T4F

391 02024733 Capacitor0402

0.047uF　K　10V

1 C162 B4d

392 02024733 Capacitor0402

0.047uF　K　10V

1 C161 T2C

393 02024733 Capacitor0402

0.047uF　K　10V

1 C237 T3f

394 02024733 Capacitor0402

0.047uF　K　10V

1 C158 T4E

395 02024733 Capacitor0402

0.047uF　K　10V

1 C157 T5F

396 02025623 Capacitor0402

5600PF　GRM36X7R562K25

1 C47 B3D

397 02025R6E Capacitor0402 5.6P(ECDGOE5R6C) 1 C107 B4E

398 02021043 Capacitor0402

0.1uF　K　10V

1 c256 b1g

399 02026823 Capacitor0402

6800P　K　25V

1 c254 b1g

400 02028202 Capacitor0402

82PF　GRM36COG820J50

1 C58 B4C

401 02026802 Capacitor0402

68P　J　50V

1 C147 B4I

402 0202R75B Capacitor0402

0.75P　B　50V

1 C104 B4G

403 0203010B Capacitor0603

1P　B　50V

1 C92 B2C

404 02031023 Capacitor0603

1000P　K　50V

1 C63 B1D

405 02031023 Capacitor0603

1000P　K　50V

1 C72 B3D

406 02031023 Capacitor0603

1000P　K　50V

1 C235 B4J

407 02031043 Capacitor0603

0.1uF　K　16V

1 C48 T4G

408 02031802 Capacitor0603

18P　J　 50V

1 C19 B1C

409 02051043 Capacitor0805

0.1uF　K　25V

1 C194 T5h

410 022Z06A0 Variable capacitor TZVY02Z060A110.6P 1 TC6 B3B

TC-600 Part List 1

－ 27 －

No. Material No. Material Name Description Qty. Ref.No. Print No. Remarks

411 022Z10A0 Variable capacitor TZVY02Z100A110.10P 1 TC2 B1C

412 022Z10A0 Variable capacitor TZVY02Z100A110.10P 1 TC1 B1D

413 022Z10A0 Variable capacitor TZVY02Z100A110.10P 1 TC5 B4E

414 022Z10A0 Variable capacitor TZVY02Z100A110.10P 1 TC3 B4G

415 022Z10A0 Variable capacitor TZVY02Z100A110.10P 1 TC4 B5F

416 03021020 Inductor 1uH 1 L43 B5J

417 03032300 Inductor 23nH 1 L44 B1E

418 03032300 Inductor 23nH 1 L16 B2B

419 03061020 Inductor 1uH 1 L1 B4B

420 03061020 Inductor 1uH 1 L14 T4H

421 03022210 Inductor 220nH 1 L4 B4J

422 03062210 Inductor 0.22uH 1 L41 T2E

423 03063320 Inductor 3.3uH 1 L46 B2C

424 03063320 Inductor 3.3uH 1 L5 B2E

425 03083310 Inductor 330nH 1 L49 B3E

426 0312601S BLM18AG601SN1D BLM18AG601SN1D 1 L8 B2A

427 0312601S BLM18AG601SN1D BLM18AG601SN1D 1 L13 B2B

428 0312601S BLM18AG601SN1D BLM18AG601SN1D 1 L6 B2D

429 0312601S BLM18AG601SN1D BLM18AG601SN1D 1 L7 B2D

430 0312601S BLM18AG601SN1D BLM18AG601SN1D 1 L12 B3G

431 0313221S BLM21PG221SN1D BLM21PG221SN1D 1 L11 B3H

432 0313600S BLM21PG600SN1D BLM21PG600SN1D 1 L15 B2G

433 0313600S BLM21PG600SN1D BLM21PG600SN1D 1 L10 B3I

434 0318150J Inductor 15nH 1 L21 B3G

435 0318180J Inductor 18nH 1 L26 B2B

436 03182202 Inductor 22nH 1 L18 B2D

437 03182202 Inductor 22nH 1 L19 B2D

438 03182202 Inductor 22nH 1 L25 B3E

439 03185N6S Inductor 5.6nH 1 L29 B3H

440 03191250 E2-0.30-1.2-5TL E2-0.30-1.2-5TL 1 L2 B3H

441 03193530 E2-0.35-1.6-3TR E2-0.35-1.6-3TR 1 L35 B4E

442 03193530 E2-0.35-1.6-3TR E2-0.35-1.6-3TR 1 L36 B4E

443 03193530 E2-0.35-1.6-3TR E2-0.35-1.6-3TR 1 L31 B4F

444 03193530 E2-0.35-1.6-3TR E2-0.35-1.6-3TR 1 L34 B5E

445 03193530 E2-0.35-1.6-3TR E2-0.35-1.6-3TR 1 L38 B5F

446 03193540 E2-0.35-1.6-4TL E2-0.35-1.6-4TL 1 L32 B4G

447 03193540 E2-0.35-1.6-4TL E2-0.35-1.6-4TL 1 L33 B4G

448 03193540 E2-0.35-1.6-4TL E2-0.35-1.6-4TL 1 L22 B4H

449 03193540 E2-0.35-1.6-4TL E2-0.35-1.6-4TL 1 L23 B4I

450 03193540 E2-0.35-1.6-4TL E2-0.35-1.6-4TL 1 L24 B4I

451 03193540 E2-0.35-1.6-4TL E2-0.35-1.6-4TL 1 L28 B4J

452 03193580 E2-0.35-1.6-8TR E2-0.35-1.6-8TR 1 L30 B3I

453 03301010 Inductor

HK1005　R10J-T

1 L17 B1C

454 03301010 Inductor

HK1005　R10J-T

1 L48 B1C

455 03301010 Inductor

HK1005　R10J-T

1 L47 B2C

456 03301010 Inductor

HK1005　R10J-T

1 L40 B5E

TC-600 Part List 1

－ 28 －

No. Material No. Material Name Description Qty. Ref.No. Print No. Remarks

457 03304700 Inductor HK1005 47NJ 1 L45 B2D

458 03304700 Inductor HK1005 47NJ 1 L39 B5E

459 04003720 Diode 1SS372(TE85L) 1 D18 T4F

460 04012690 Diode 1SV269(TPH2) 1 D10 B2B

461 0402190G LED KPT1608-SGC(High_green) 1 D22 T2J

462 0402190R LED KPT-1608SRC(High_red) 1 D24 T2J

463 04032220 Diode

DAN222（TL）

1 D19 T4G

464 04072376 Diode MA2S37600L 1 D7 B1C

465 04072376 Diode MA2S37600L 1 D8 B1C

466 04072376 Diode MA2S37600L 1 D3 B2D

467 04072376 Diode MA2S37600L 1 D2 B2E

468 04072S11 Diode MA2S11100L 1 D13 B4u

469 04072S11 Diode MA2S11100L 1 D9 B2C

470 04073600 Diode MAZ36000L 1 D4 B1D

471 04077700 Diode MA2Z07700L 1 D11 B4I

472 0407S077 Diode MA2S07700L 1 D5 B3F

473 0407S077 Diode MA2S07700L 1 D6 B3F

474 0407S077 Diode MA2S07700L 1 D12 B5H

475 05001362 Triode 2SA1362(GR) 1 Q40 T3F

476 05024226 Triode 2SC4226-R24 1 Q15 B2D

477 05024988 Triode 2SC4988FRTR 1 Q17 B3G

478 05025108 Triode 2SC5108-Y(TE85L) 1 Q13 B2B

479 05025108 Triode 2SC5108-Y(TE85L) 1 Q14 B2D

480 05025108 Triode 2SC5108-Y(TE85L) 1 Q22 B4D

481 05025343 2SC5343EG 2SC5343EG 1 Q18 B2D

482 05025343 2SC5343EG 2SC5343EG 1 Q19 B4A

483 05025343 2SC5343EG 2SC5343EG 1 Q20 B4A

484 05025343 2SC5343EG 2SC5343EG 1 Q26 T4G

485 05025343 2SC5343EG 2SC5343EG 1 Q24 T5F

486 05025343 2SC5343EG 2SC5343EG 1 Q25 T5F

487 05045080 Triode 2SK508NV(K52) 1 Q8 B2C

488 0505114E Triode DTA114EE(TL) 1 Q10 B4D

489 0505114Y Triode DTA114YE(TL) 1 Q47 b3b

490 0505114Y Triode DTA114YE(TL) 1 Q34 T2A

491 0505114Y Triode DTA114YE(TL) 1 Q9 T2B

492 0506114E Triode DTC114EE(TL) 1 Q39 T2F

493 0506114E Triode DTC114EE(TL) 1 Q28 B2J

494 0506114E Triode DTC114EE(TL) 1 Q30 B2J

495 0506114E Triode DTC114EE(TL) 1 Q45 T1B

496 0506144E Triode DTC144EE(TL) 1 Q12 T2E

497 0508UMC4 Triode UMC4(NTR) 1 Q7 B1D

498 0508UMG3 Triode UMG3N(N-TR) 1 Q1 B1F

499 0508UMG3 Triode UMG3N(N-TR) 1 Q2 B2F

500 0509572T Triode UPA572T 1 Q3 B2G

501 05107170 Triode FMMT717TA 1 Q4 B1F

502 05107170 Triode FMMT717TA 1 Q5 B1F

TC-600 Part List 1

－ 29 －

No. Material No. Material Name Description Qty. Ref.No. Print No. Remarks

503 05119570 Triode PRF957 1 Q16 B1D

504 06002430 FET 2SJ243-T1 1 Q6 B1C

505 06011588 FET 2SK1588-T1 1 Q41 T3F

506 06011824 FET 2SK1824-T1 1 Q46 b2f

507 06011824 FET 2SK1824-T1 1 Q21 B5B

508 06011824 FET 2SK1824-T1 1 q50 T2G

509 0601rd01

●FET

RD01MUS1 1 Q32 B3G

510 0601rd07

●FET

RD07MVS1 1 Q31 B3I

511 06023200 FET 3SK320 1 Q23 B3E

512 06023200 FET 3SK320 1 Q27 B5E

513 0701P502 XC6201P502R XC6201P502R 1 IC4 T1D

514 072100v0 IC NJM2100V 1 IC3 T4F

515 0724C082 IC AT24C08N-10S1-2.7 1 IC5 T5B

516 072902V0 IC NJM2902V 1 IC7 B3C

517 07311360 IC

TA31136FN（EL）

1 IC1 B4C

518 07382239 M38223M4H-489HP M38223M4H-489HP 1 IC11 T3C

519 07312020 IC

TB31202FN（EL）

1 IC2 B4u

520 076278F0 IC KIA6278F 1 IC8 T3E

521 079140NR IC PST9140NR 1 IC9 T2A

522 10737281

●Transistor

7.3728MHZ 1 X3 T3B

523 T0506105 Tantalum capacitor0805

1.0uF　6.3V.M

1 C86 B1F

524 T0506105 Tantalum capacitor0805

1.0uF　6.3V.M

1 C85 B1G

525 T0506105 Tantalum capacitor0805

1.0uF　6.3V.M

1 C87 B1G

526 T0506105 Tantalum capacitor0805

1.0uF　6.3V.M

1 C200 T4E

527 T0506106 Tantalum capacitor0805

10uF　6.3V.M

1 C202 B3B

528 T0606156 Tantalum capacitor1206 15UF/6.3V.M 1 C115 B2C

529 T0606156 Tantalum capacitor1206 15UF/6.3V.M 1 C177 T1D

530 T0606226 Tantalum capacitor1206

22uF　6.3V

1 c247 T3E

531 T0606226 Tantalum capacitor1206

22uF　6.3V

1 c248 T3E

532 T0610106 Tantalum capacitor1206

10uF　10V.M

1 C155 B4A

533 T0610106 Tantalum capacitor1206

10uF　10V.M

1 C159 B4B

534 T0610106 Tantalum capacitor1206

10uF　10V.M

1 C1 B4B

535 T0610106 Tantalum capacitor1206

10uF　10V.M

1 C125 B4F

536 T0610155

1206

TMCSA1A155MTR.1.5UF/10V.M

1206

TMCSA1A155MTR.1.5UF/10V.M

1 C124 B1B

537 T0610685 Tantalum capacitor1206 6.8UF/10V.M 1 C112 T2G

538 T0616105 Tantalum capacitor1206 TMCSA1C105MTR 1 C174 T3F

539 T0616225 Tantalum capacitor1206

2.2uF　16V　K

1 C165 T5F

540 T0616475 Tantalum capacitor1206

4.7uF　16V.K

1 C117 B1B

541 T0506475 Tantalum capacitor0805

4.7uF　6.3WV.M

1 c214 b3b

542 T0616475 Tantalum capacitor1206

4.7uF　16V.K

1 C173 T4F

543 T2006227 Tantalum capacitor

220uF　6.3V　C Packing

1 C203 T5G

544 T2016476 Tantalum capacitor

47uF　16V　Type C(Hitachi)

1 C120 B2G

545 T0606226 Tantalum capacitor1206

22uF　6.3V

1 C118 T2E

TC-600 Adjustment Description

－ 30 －

Adjustment Description

The radio can be adjusted with PC programming software or by manual adjustment. Manual adjustment
procedure of TC-600 is shown as follows. (Refer to ―Model Set Mode‖ and ―Manual Adjust Mode‖ in
Software Specification section.)

Instrument:

Radio Communication Test Set 1 set
Scanner 1 set
3A/10V Power Supply 1 set
Digital Voltmeter 1 set

3A Ammeter 1 set

Adjustment:

1. Initialization

It’s necessary to set the model and initialize the radio before adjustment because there is no needed
information in EEPROM when the radio is manufactured. Please refer to the ―Model Set Mode‖ in
Software Specification section for details.

2. Adjustment

Some items can be adjusted in Conventional Mode and the others in Manual Adjust Mode. Turn on the
power, the radio enters the Conventional Mode. If Manual Adjust Mode is enabled, turn on the power
while holding down PTT and MONI key simultaneously, the radio enters Manual Adjust Mode in 2
seconds. (Refer to ―Manual Adjust Mode‖ in Software Specification section.)

VCO

Item

Condition

Measurement

Adjustment

Specification
/Remarks

Test Instrument

Terminal

Part

Method

1. Power Supply

1.power supply voltage 7.2V DC

2.Transmit VCO
Lock Voltage

1. TX High. Turn to CH14 in
manual adjust mode and press
PTT.

Digital Voltmeter

CV

TC1

3.0V±0.1V

2. TX Low. Turn to CH13 in
manual adjust mode and press
PTT.

>0.7V

3. Receive
VCO Lock
Voltage

1. RX High. Turn to CH14 in
manual adjust mode.

TC2

2.6V±0.1V

2. RX Low. Turn to CH13 in
manual adjust mode.

>0.7V

Note: The radio transmits no matter whether VCO is locked or unlocked. Enter the Manual Adjust Mode

for check in case of unlocked TX VCO.

TC-600 Adjustment Description

－ 31 －

RECEIVER: (Enter the Manual Adjust Mode)

Item

Condition

Measurement

Adjustment

Specification

/Remarks

Test Instrument

Terminal

Part

Method

1.
Band Pass
Filter

1. RX Center. Turn
to CH12 in manual
adjust mode.

Scanner

ANT. TP2

TC3
TC4
TC5

Adjust the waveform to
the top, and the top is flat,
the bandwidth is about
20MHz, the sign of RX
central frequency is at the
center of the waveform.

2.Sensitivity

1. RX Center. Turn
to CH12 in manual
adjust mode.

Radio
Communication
Test Set
SSG output:

-118dBm
MOD: 1KHz
DEV:

±3KHz
FILTER:

0.3-3.4kHz

ANT

Speaker

Jack

Check

SINAD: 12dB
or higher

2. RX Low. Turn to
CH13 in manual
adjust mode.

3. RX High. Turn to
CH14 in manual
adjust mode.

3.Squelch

1. RX Center. Turn
to CH2 in manual
adjust mode. Adjust
by PTT or Function
key.

Radio
Communication
Test Set
SSG output:

-117dBm

ANT

Speaker

Jack

Level 9
Adjust to just close the
squelch.

Adjust to
squelch level 9

2. RX Center. Turn
to CH3 in manual
adjust mode. Adjust
by PTT or Function
key.

Radio
Communication
Test Set
SSG output:

-125dBm

Level 3
Adjust to just close the
squelch.

Adjust to
squelch level 3

TC-600 Adjustment Description

－ 32 －

Transmitter

Item

Condition
Measurement

Adjustment

Specification

/Remarks

Test Instrument

Terminal

Parts

Method

1.Transmit
frequency

1. TX Center. Turn to CH12
in manual adjust mode and
press PTT.

Radio Communication
Test Set

ANT

TC6

Adjust it to center
frequency

Error≤±250Hz

2. Max.
Deviation

1. TX Center. Turn to CH12
in manual adjust mode and
press PTT.

Radio Communication
Test Set
LPF: 15KHz
AF:1KHz 120mV

ANT

MIC Jack

VR2

Adjust deviation to:

4.2kHz±100Hz(W)

2.2kHz±100Hz(N)

3.Modulati
on
Sensitivity

1. TX Center. Turn to CH12
in manual adjust mode and
press PTT.

Radio Communication
Test Set
FILTER:

0.3-3.4KHz
AF: 1KHz 13±3mV

ANT

MIC Jack

Check deviation:

2.2KHz-3.6KHz

4. CTCSS
Balance

1. TX Center. CTCSS:

67.0Hz. Turn to CH4 in
manual adjust mode.

Radio Communication
Test Set
LPF:300Hz

ANT

VR3

Adjust VR3,
deviation tested on
condition 1 and
condition 2 are
consistent, the
difference≤200Hz

67.0Hz
CTCSS

2. TX Center. CTCSS:

250.3Hz. Turn to CH4 in
manual adjust mode and
press PTT.

250.3Hz
CTCSS

5. CTCSS
Deviation

1. TX Center. CTCSS:

67.0Hz. Turn to CH4 in
manual adjust mode. Adjust
by PTT or Function key.

Radio Communication
Test Set
LPF: 300Hz

ANT

Adjust deviation to:

0.65kHz±
100Hz(W)

0.35kHz±100Hz(N)

6. CDCSS
Deviation

1. TX Center.
CDCSS: 023. Turn to CH5 in
manual adjust mode. Adjust
by PTT or Function key.

Adjust deviation to:

0.65kHz±
100Hz(W)

0.35kHz±100Hz(N)

7. DTMF
Deviation

TX center, turn to CH15 in
manual adjust mode

Radio Communication
Test Set
LPF: 15KHz

ANT

Observe

Deviation:

≤3.5KHz(W)
≤2.5KHz(N)

8. Low
Battery
Alert Level

1. Turn to CH1 in manual
adjust mode. Adjust the
power supply voltage to 5.5V.
Adjust by PTT or Function
key.

Digital Voltmeter

Adjust the level to
make LED just
flash.

Note: In Manual Adjust Mode, when channel selector knob is rotated to CH1-CH16, MIC jack can’t
connect with external cables. After adjustment is completed, short out the two SELF points and then turn
the power on, the radio enters Model Set Mode. Then press PTT to disable the manual adjust mode.

TC-600 Disassembly and Assembly for Repair

－ 33 －

Disassembly and Assembly for Repair

Disassemble the radio

1. Turn off the radio.

2. Remove the Battery:

a. Push the battery latch on the back panel towards the top of the radio.
b. Pull the top of the battery away from the radio chassis, and lift the battery from the radio. (See

Figure 1)

①

②

③

Fig. 1

3. Disassemble the main unit (aluminum chassis and PCB)

a. Remove the two screws at the bottom of the chassis.
b. Pull the Power/Volume Control knob and Channel Selector knob off.
c. Remove the antenna at top of the radio. (See Figure 2)

①

③

②

Fig. 2

TC-600 Disassembly and Assembly for Repair

－ 34 －

d. Lift the bottom of the chassis and pull it away from the front cover. (See Figure 3)

Fig. 3

The disassembled main unit is shown as Figure 4.

Fig. 4

4. Disassemble the PTT key

a. Remove the PTT holder (plastic) out of the PTT key.
b. Push the PTT key in indicated direction until it is out of the front cover. (See figure 5)

Fig. 5

Assemble the radio

1. Attach the PTT key

a. Press the PTT key into the corresponding opening in the front cover.
b. Slide the PTT holder into the key in indicated direction.

(See Figure 6)

TC-600 Disassembly and Assembly for Repair

－ 35 －

Fig. 6

2. Attach the battery

a. Turn off the radio.
b. Insert the tabs at the bottom of the battery into the slots at the bottom of the radio chassis.
c. Press the top of the battery towards the radio until a ―click‖ is heard. (See Figure 7)

①

②

Fig. 7

TC-600 Exploded View

－ 36 －

Exploded View

51

49

48

52

27

26

20

21

19

22

23

24

25

50

15

16

1

2

3

4

5

6

8

7

9

10

11

32

34

33

18

17

28

30

31

29

12

14

13

37

41

40

36

39

38

35

43

44

45

42

47

46

TC-600 Part List 2

－ 37 －

Part List 2

No.

Material Name

1

TC600 Antenna

2

TC600PTT key

3

TC600PTT holder

4

TC600 light guide

5

TC600 knob (enc)

6

TC600 knob (vol)

7

Inner liner knob (enc)

8

Inner liner knob (vol)

9

TC600 spring (battery latch)

10

TC600 battery latch

11

Escutcheon (SP)

12

Silica gel washer (SP)

13

Speaker 4Ω 0.5W

14

Sponge cushion (SP)

15

Connector

16

Connecting line (SP)

17

TC600 fixing ring (SP)

18

Nut (knob)

19

Gray-code encoder switch EC10ST16-HYT-1

20

Switch (vol)

21

PHONE JACK 2SJ-2435-001

22

MIC JACK ISJ-2584-001

23

TC600 holder (plus connector)

24

TC600 contact sheet

25

TC600 plus connector

26

Cross-head self tapping screw ST2.0X4

27

TC600 sponge cushion (plus connector)

28

TC600 waterproof ring

29

Machine screw 2.5×4

30

Antenna pedestal (SMA-B01)

31

TC600 Aluminum chassis

32

TC600 contact sheet (battery)

33

Minus connector (battery)

34

Cross-head self tapping screw ST2.0X4

35

TC600 PVC sheet (aluminum chassis)

36

Holder (belt clip)

TC-600 Part List 2

－ 38 －

37

Spring (belt clip)

38

Shaft (belt clip)

39

TC600 Belt clip

40

TC600 front case (battery)

41

Charging connector (battery)

42

Main unit (battery)

43

TC600 rear case (battery)

44

Plus/minus connector (battery)

45

Machine screw M2X9

46

PVC sheet

47

PCB board

48

Cross-head self tapping screw ST2.0X4

49

Gasket (MIC)

50

Switch (PTT) SKHLLBA010

51

TC600 MIC cover

52

TC600 front case

TC-600 Packing

－ 39 －

Packing

TC-600 Specifications

－ 44 －

Specifications

Frequency Range

400 MHz ~420 MHz 450 MHz ~470 MHz
136 MHz ~150 MHz 150 MHz ~174 MHz

Channel Capacity (simplex)

16

Channel Spacing

25KHz /12.5KHz

Antenna Impedance

50Ω

Microphone Impedance

2KΩ

Operating Voltage

7.2V DC

Frequency Stability

±5.0×10-6

Transmitter

Carrier Frequency Error

±5×10-6

Output Power

4.0W/2W

Modulation Sensitivity

13±3mV

Modulation Distorsion

≤5%

Modulation Limit

≤5KHz / 2.5KHz

Bandwidth

≤16 KHz / 8.5 KHz

Audio Response

From 6 dB/oct. Pre-Emphasis ±3dB

Conducted Spurious Emission

≤7.5μ W

Adjacent Channel Power

≤-65 d B

Receiver

Reference Sensitivity

≤ 0.28μV / 0.35μV

Unsquelch Sensitivity

≤0.4μV

Audio Power

500mW (4Ω)

Audio Distortion

≤5%

Modulation Acceptance

≥│±7 KHz│/│±3.5 KHz│

Audio Response

From 6 dB/oct. De-Emphasis +2dB -8dB

Co-Channel Rejection

≥-8 d B

Blocking

≥85d B

Adjacent Channel Selectivity

≥65 d B / 60 d B

Spurious Response Rejection

≥60 d B

Intermodulation Rejection

≥60 d B / 55 d B