Page 1
8 1 3 PD70 L0 0 0 1 0
Page 2
1
This guide is helpful for you to quickly know how to use the
PD70X / PD70XG/ PD70X (X may represent 2, 5, 6 or 8) LT
digital portable radio.
1. Instructional Icons
The following icons are available through this guide:
: indicates functions that are available on digital channel
only.
: indicates functions that are available on analog channel
only.
Functions marked with no function icons are available on both
analog and digital channels.
2. Product Overview
Product Controls
No. Part Name No. Part Name
1 SK1 (Side Key 1) 8
Radio On-Off/Volume
Control Knob
2 PTT Key 9 Microphone
3 SK2 (Side Key 2) 10 Accessory Jack
4 TK (Top Key) 11 Battery Latch
5
Channel Selector
Knob
12 Antenna
6 Speaker 13 Belt Clip
7 LED Indicator 14 Battery
Programmable Keys
For enhanced convenience, you may request your dealer to program the keys SK1, SK2 and TK as shortcuts to radio functions.
See the Owner’s Manual for details.
3. Status Indication
LED Indicator
LED Indicator Radio Status
The LED ashes green. Powering on
The LED glows red. Transmitting
The LED glows green. Receiving
The LED ashes orange
slowly.
Hunting
The LED ashes orange
rapidly.
Emergency
The LED glows orange.
After voice communication ends,
you can hold the PTT key to talk
while the LED glows orange.
Page 3
2
4. Basic Operations
Powering On/Off
Rotate the Radio On-Off/Volume Control knob clockwise/
counter-clockwise until a click is heard to turn the radio on/off.
Adjusting the Volume
After turning the radio on, rotate the Power On-Off/Volume
Control knob clockwise to increase the output sound volume, or
counter-clockwise to decrease it.
Adjust Power Level
With this feature, you may switch power levels quickly. Generally,
we recommend you to adopt low power for battery saving.
However, if you cannot communicate with radios located at a
distant place with low power, please select high power.
Press the programmed Adjust Power Level key to switch the Tx
power of the current channel between High and Low.
Selecting a Zone
A zone is a group of channels exhibiting the same property. You
can list such channels into a zone for convenient management to
them. The radio supports 3 zones: Zone 1, Zone 2 and Zone 3.
Each zone contains 16 channels at most.
You may quickly toggle to your wanted zone by pressing the
programmed Zone Up or Zone Down key. When toggling to a
zone, you will hear the alert tone for the zone (one alert tone for
Zone 1, two alert tones for Zone 2 and three alert tones for Zone
3).
Selecting a Channel
After turning the radio on, rotate the Channel Selector knob to
select a needed channel. You can also switch to the designated
channel by pressing the Preset Channel key.
If the Channel Notify function is active, you will hear the
corresponding channel number when switching to any channel.
Switching the Channel Mode
Each channel can be programmed as either analog channel or
digital channel via your dealer. If the current zone includes both
analog and digital channels, you may quickly switch between
digital and analog channels through the Channel Selector knob.
5. Call
To ensure optimal volume of the receiving radio, hold the palm
microphone approximately 2.5 to 5 centimeters away from your
mouth.
Private Call
Initiating a Call
In standby mode, hold the PTT key to transmit a private call to
the private call contact preset for the current channel.
Note: Your dealer may preset a contact for each
digital channel. The preset contact could be
a private call contact, a group call contact
or an all call contact.
Receiving a Call or Calling Back
When a private call is received, you can listen to it without any
operation. You may hold the PTT key within the preset time
period to call back.
Page 4
3
Group Call
Initiating a Call
In standby mode, hold the PTT key to transmit a group call to the
group call contact preset for the current channel.
Receiving a Call or Calling Back
When a group call is received, you can listen to it without any
operation, and you may hold the PTT key within the preset time
period to call back.
Calls on Analog Channels
To transmit on an analog channel, hold down the PTT key and
speak into the microphone. To receive, release the PTT key.
Time-out Timer (TOT)
TOT aims to prevent any user from occupying a channel for
an extended period. If the preset time expires, the radio will
automatically terminate the transmission and keep beeping. To
stop beeping, please release the PTT key. You must wait for
a certain time period (preset by your dealer) to initiate another
transmission.
Page 5
中文
1
本手册帮助您快速掌握PD700 /PD700G/ PD700 Business 数字手
持终端的基本操作
一.图标说明
本手册中会使用以下图标，其含义如下：
:
表示数字信道独有的功能，只能在数字信道上使用。
:
表示模拟信道独有的功能，只能在模拟信道上使用。
未用图标区分的功能在数字信道和模拟信道上都可使用。
二.熟悉本机
部件介绍
序号 部件名称 序号 部件名称
1 SK1（侧键1） 8 电源开关/音量控制旋钮
2
P T T键 （ 发射按
键）
9 麦克风
3 SK2（侧键2） 10 附件接口
4 TK（顶部键） 11 电池推钮
5 信道选择旋钮 12 天线
6 扬声器 13 皮带夹
7 LED指示灯 14 电池
可编程键
为了提升操作便利性，本机的3个可编程键【S K1】、【S K2】
和【TK】，可由您的经销商编程为功能快捷键，具体请参见说明
书。
三.状态指示
LED
指示灯
指示灯状态 对讲机状态
绿灯闪烁 正在开机
红灯长亮 正在发送
绿灯长亮 正在接收
橙灯慢闪 正在扫描
橙灯快闪 紧急状态
橙灯长亮
语音 结束后，在 橙灯长亮期 间，
用户可以按住【PTT】键通话。
四.基本操作
开机与关机
如需开机，请 顺时 针旋转【电源开关/音量控制 】旋 钮直到听到
“咔嗒”声；如需关机，请逆时针旋转此旋钮直到听到“咔嗒”
声。
Page 6
中文
2
调节音量
开机后，顺时针旋转【电源开关/音量控制】旋钮可增大语音接收
音量，逆时针旋转可减小语音接收音量。
调整功率级别
此功 能可实 现功率 级别的 快速切换。 当通信 距离满 足您的 需求
时，可选择低功率以节约电量。而当低功率无法使您与距离较远
的其他终端通信时，请选择高功率。
按【调整功率级别】快捷键使当前信道的发射功率在高、低之间
切换。
选择区域
区域是一个信道组，即您可将具有相同属性的信道列入一个区域
中，这样便于您对现有信道进行有效管理。本机支持3个区域：区
域1、区域2和区域3。每个区域最多包含16个信道。
按【区域上调】或【区域下调】快捷键，即可在三个区域之间切
换。每切换到一个区域时，同时会响与区域号数相同的提示音。
选择信道
开机后，旋转【信道选择】旋钮即可选择所需信道。如果经销商
开启了对讲机的信道播报功能，对讲机将播报信道号。目前只有
中英文两种播报语音，具体由经销商设定。
数模切换
对讲机中的每个信道都可由经销商配置为模拟信道或数字信道。
若当前区域包含数字信道和模拟信道，您可使用【信道选择】旋
钮切换至模拟信道或数字信道。
五.呼叫
为了保证接收方对讲机的最佳接收音量，发射时请保持麦克风距
离嘴大约 2.5 到 5 厘米。
个呼
发起呼叫
在待机状态下，按住【P T T】即可对当前数字信道上预设的个呼
联系人发起个呼。
接收呼叫或回呼
接收 到个呼 后，您 无需任 何操作即可 接听， 在预设 时间内 按住
【PTT】可发送回呼。
组呼
发起呼叫
在待机状态下，按住【P T T】即可对当前数字信道上预设的组呼
联系人发起组呼。
接收呼叫或回呼
接收 到组呼 后，您 无需任 何操作即可 接听， 在预设 时间内 按住
【PTT】可发送回呼。
模拟信道呼叫
在模 拟信道上， 如需发 射，请按住 【P T T】键 并对着 麦克风讲
话；如需接收，请松开【PTT】键。
超时禁发
此功能可避免用户过久占用信道。当您连续通话时间超过经销商
编程预设的时间，本产品将自动终止通话并且发出警告音，松开
【P TT】键可以停止警告音。如果您需要再次通话，请在间隔一
段时间后再次按下【PTT】键。
备注：您可通过经销商为每个数字信道预设一个联系
人，该联系人可以是个呼联系人，也可以是组呼
或全呼联系人。
Loading...