HySecurity HYNET GATEWAY SFP 4/1, MX3867, StrongArmPack DC 10, StrongArmPack DCS 10, StrongArmPack DC 14 Installation Manual

StrongArmPark DC 10 and StrongArmPark DCS 10 StrongArmPark DC 14 and StrongArmPark DCS 14

Installation Manual for HyNet Attachment: MX3867

This document is a supplemental document that provides specic information regarding conguration of the HySecurity gate operator with installation and wiring of the HyNet Gateway. For safety considerations and information specic to your gate operator, refer to the HySecurity gate operator product manuals.

HyNet Components

LED Indicators

4321

Height

1¼ inches

SFP Module (100/1000/2500)

Mounting Plate

4 x 7½ inches

RS-485

Micro SD Card Slot

USB OTG

Micro USB

Reset Button

LED (position 1)

Table 1: HyNet LED Indicators

LED Position LED Color Indicates

1 RED ashing No communication from gate operator to HyNet.

1 Green steady Communication is established between gate operator and HyNet.

2 RED steady Gate operator network communication is not congured or established.

2 RED ashing HyNet is attempting to connect to network (web interface).

2 GREEN ashing

3 RED steady Hardware fault.

Network (web interface) is established and working. (May not be wholly congured, yet. Verify conguration with your IT administration.)

Managed Switch RJ-45 Integration Hub 4-Port Copper Gigabit (100/1000/2500)

3 RED ashing Charge is low on coin battery. Replace coin battery.

3 GREEN steady Hardware functioning and coin battery charged.

4 Red steady or no LED lit HyNet internal switch is not functioning.

4 GREEN steady HyNet internal switch is functioning.

Drawing is not to scale

StrongArmPark DC HyNet Assembly

Alcohol wipe

Use alcohol wipe to clean

HyNet mounting plate

mounting plate surface before applying Velcro

Velcro strip

Peel off protective layer and adhere Velcro

®

strip to HyNet mounting plate.

Velcro

Adhere to gate operator chassis.

adhesive backing.

®

strip

HyNet Assembly

Mount HyNet to StrongArmPark DC and StrongArmPark DCS

Set the HyNet onto the chassis so the ports are accessible as shown in the illustration.

Connect wiring.

5

6

See page 5.

Replace and secure

covers.

4

Remove front

cover panel

1

Peel protective paper off

®

Velcro

strip.

2

Adhere the Velcro® strip to the inside portion of

the StrongArmPark DC chassis. Press rmly.

3

NOTE: Recommended HyNet location is shown in the illustration. Ambient temperature for adhesion

is between 45˚ and 85˚ F.

Wiring the HyNet Gateway

24VDC

24VAC

12VDC

HyNet

RS-485 port

Pin 1, +24V

RS-485

Connector

Attach to RS-485 port on HyNet.

1

5

Supply RJ-45 network

connection

COMMON TERMINALS

Optional +24VDC

if RADIO OPTIONS

+24V is occupied

COM

STOP

OPEN

CLOSE

RADIO

OPEN PARTIAL

SENSOR 2

SENSOR 3

EXIT LOOP

BLOCK EXIT IN OBS LOOP OUT OBS LOOP

CENTER LOOP

SENSOR 1 SENSOR

COM

+ 24 V

EMERG OPEN

Smart DC Controller

24VDC

12VDC

OPEN

M

O

SHOW LEDs

C

DU

Installer supplied shielded

cable

Attach shielded

cable to wire

2

harness.*

*Measure distance between HyNet and Controller connections for appropriate shielded cable length.

NOTE: More detailed wiring information is shipped with the HyNet.

Wire harness

(supplied in box)

2

DC

ER

S

U

E

G

D

E

V

M

O

+24

C

N

E

P

O

COM

A

B

E

T

A

G

L

A

NS

O

I

T

P

O

ADI

R

USB port

RS-485 ports

O

N

Pin 1, COM

Connect to RS-485 port on Smart DC

3

Controller.

Connect ying

lead to +24V.

Drawing is not to scale.

4

2

C

D

R

E

S

U

A

COM

2

+

E

G

D

E

O

I

D

A

R

DU

S

ON

I

T

P

TE

A

G

L

A

B

COM

N

E

P

O

V

4

COM

O

N

NOTE: The Smart DC Controller pin layout changed a few years ago. On controllers with part numbers marked MX001457 and MX3037 Revisions A, B, and C,

be sure you're connecting the ying lead to the +24V

spade located under RADIO OPTIONS.

Smart DC Controller

HySecurity gate operators provide a 2-wire, serial interface (RS-485 connection) which allows remote access to one or more operators.

When the physical connection is made and protocols are established, an SA (System Address) must be assigned for each operator through its Installer Menu.

For network communication, choosing a “SA” of 1 to 4 establishes individual network polling addresses. HyNet only utilizes numbers 1, 2, 3, or 4.

A “SA” of zero means no network communication is desired.

COMMON TERMINALS

COM

STOP

OPEN

CLOSE

RADIO

OPEN PARTIAL

SENSOR 2

SENSOR 3

EXIT LOOP

BLOCK EXIT

IN OBS LOOP OUT OBS LOOP

CENTER LOOP

SENSOR 1 SENSOR

COM

+ 24 V

EMERG OPEN

OPEN

SHOW LEDs

24VDC

12VDC

To access Installer Menu, press Menu button twice. Then, press

1

Reset and Open.

Press Select to navigate to Installer Menu item "SA" System Address.

SA 0 (OFF) SYSTEM ADDRESS

SA 1 SYSTEM ADDRESS

CLOSE

OPEN

STOP

SELECT

MENU

RESET

Press Select again to set gate operator's system address

2

DC

ER

S

U

E

G

O

D

E

B

M

O

C

DU

E

T

A

G

L

A

P

O

ADI

R

V

+24

N

E

P

O

COM

A

N

M

O

C

NS

O

I

T

2

(Each gate operator attached to the same HyNet must have a unique SA number. Choose 1, 2, 3, or 4.)

To exit Menu mode, press Menu. The

3

gate operator returns to Run mode.

Refer to Table 1: HyNet LED Indicators on page 2.

4

Solid green means serial communication is active and functioning well.

For IP network setup, refer to the HyNet Quick Start

5

manual supplied in the HyNet box.

Installer’s CheCklIst

Date Installed: ________________ Gate Operator Model: _________________________________________________________________

Site Location: __________________________________________________________________________________________________________

HyNet Serial Number: ___________________________________

Gate Operator Serial Number: ___________________________

Customer Name: _______________________________________________________________________________________________________

Mailing Address: ________________________________________ Inspected by: ____________________________________________

________________________________________________________ Date Inspected: __________________________________________

Phone Contact: _________________________________________ Phone contact number: ___________________________________

Checked Initials

1. Site Planning  _____________

RJ-45 cable to system network.

2. Safety  _____________

Review Important Safety Information in the gate operator's product manual.

Warning labels apparent and afxed properly.

Area around the gate and gate operator free of debris, cabinets/chassis include locking mechanism.

3. Electrical  _____________

3.1 Grounding

• NFPA 780 Standard for the Installation of Lighting Protection Systems.

• Solid copper ground rod (⅜-inch diameter, 10 ft length) driven into ground within 3 ft of the gate operator.

• Single length of unspliced 6AWG copper wire less than 3 ft long attached to lug nut in gate operator.

3.2 Gate operator has current software loaded.

3.3 Congure the Controller

• Set the System Address (SA) in the Installer Menu.

• Communicate (verify) system address to IT Network Admin for proper web page conguration.

4. Review gate operator installation checklist from gate operator manual  _____________

5. Take photographs of installation and provide an End User Demo  _____________