HyperX HX434C19FB2-8 Technical data

Memory Module Specifications

HX434C19FB2/8

HX434C19FB2/

8GB 1G x 64-Bit

B 1G x 64-Bi

DDR4-3466 CL19 288-Pin DIMM

SPECIFICATIONS

DESCRIPTION

HyperX HX434C19FB2/8 is a 1G x 64-bit (8GB) DDR4-3466 CL19 SDRAM (Synchronous DRAM) 1Rx8, memory module, based on eight 1G x 8-bit FBGA components per module. supports Intel® Extreme Memory Profiles (Intel® XMP) 2.0. Each module has been tested to run at DDR4-3466 at a low latency timing of 19-23-23 at 1.2V. shown in the Plug-N-Play (PnP) Timing Parameters section below. The JEDEC standard electrical and mechanical specifications are as follows:

Additional timing parameters are

Each module

CL(IDD) Row Cycle Time (tRCmin) Refresh to Active/Refresh

Command Time (tRFCmin) Row Active Time (tRASmin) Maximum Operating Power UL Rating Operating Temperature Storage Temperature

*Power will vary depending on the SDRAM used.

19 cycles

45.75ns(min.) 350ns(min.)

24.234ns(min.) TBD W* 94 V - 0

C to +85o C

C to +100o C

-55

FEATURES

• Power Supply: VDD = 1.2V Typical

• VDDQ = 1.2V Typical

• VPP = 2.5V Typical

• VDDSPD = 2.2V to 3.6V

• On-Die termination (ODT)

• 16 internal banks; 4 groups of 4 banks each

• Bi-Directional Differential Data Strobe

• 8 bit pre-fetch

kingston.com/hyperx

hyperxgaming.com

Note: The PnP feature offers a range of speed and timing options to support

the widest variety of processors and chipsets. Your maximum speed will be determined by your BIOS.

JEDEC/XMP TIMING PARAMETERS

• JEDEC/PnP: DDR4-3466 CL19-23-23 @1.2V

•XMP Profile #1: DDR4-3466 CL19-23-23 @1.2V

•XMP Profile #2: DDR4-2933 CL17-19-19 @1.2V

• Burst Length (BL) switch on-the-fly BL8 or BC4(Burst Chop)

• Height 1.340” (34.04mm), w/heatsink

Continued >>

Document No. 4808560A 02/14/18 Page 1

continued

MODULE WITH HEAT SPREADER

7.08 mm

133.35 mm

34.04 mm

MODULE DIMENSIONS

All measurements are in millimeters.

(Tolerances on all dimensions are ±0.12 unless otherwise specified)

133.35

129.55

2.10

±±0.15

3.00

Detail A

Pin 1

0.15

3.35

2.70

The product images shown are for illustration purposes only and may not be an exact representation of the product. Kingston reserves the right to change any information at anytime without notice.

28.90

Detail B Detail D Detail C

Pin 35 Pin 47

64.60

Detail E

FOR MORE INFORMATION, GO TO HYPERXGAMING.COM

All Kingston products are tested to meet our published specifications. Some motherboards or system configurations may not operate at the published HyperX memory speeds and timing settings. Kingston does not recommend that any user attempt to run their computers

the published HyperX memory speeds and timing settings. Kingston does not recommend that any user attempt to run their computers faster than the published speed. Overclocking or modifying your system timing may result in damage to computer components.

faster than the published speed. Overclocking or modifying your system timing may result in damage to computer components.

HyperX is a division of Kingston.

Pin 105 Pin 117

56.10

22.95

31.25

11.00

8.00

17.60

14.60

Document No. 4808560A Page 2

hyperxgaming.com