HyperX HX426C16FB2K2-16 User Manual

)

Memory Module Specifications

HX426C16FB2K2/16

HX426C16FB2K2/1

16GB (8GB 1G x 64-Bit x 2 pcs.)

16GB (8GB 1G x 64-Bit x 2 pcs. DDR4-2666 CL16 288-Pin DIMM

SPECIFICATIONS

DESCRIPTION

HyperX HX426C16FB2K2/16 is a kit of two 1G x 64-bit (8GB) DDR4-2666 CL16 SDRAM (Synchronous DRAM) 1Rx8, memory module, based on eight 1G x 8-bit FBGA components per module. Each module kit supports Intel® Extreme Memory Profiles (Intel® XMP) 2.0. been tested to run at DDR4-2666 at a low latency timing of 16-18-18 at 1.2V. Plug-N-Play (PnP) Timing Parameters section below. The JEDEC standard electrical and mechanical specifications are as follows:

Note: The PnP feature offers a range of speed and timing options to support the widest variety of processors and chipsets. Your maximum speed will be determined by your BIOS.

Additional timing parameters are shown in the

Total kit capacity is 16GB. Each module has

CL(IDD) Row Cycle Time (tRCmin) Refresh to Active/Refresh

Command Time (tRFCmin) Row Active Time (tRASmin) Maximum Operating Power UL Rating Operating Temperature Storage Temperature

*Power will vary depending on the SDRAM used.

16 cycles

45.75ns(min.) 350ns(min.)

29.25ns(min.) TBD W* 94 V - 0

C to +85o C

C to +100o C

-55

FEATURES

• Power Supply: VDD = 1.2V Typical

• VDDQ = 1.2V Typical

• VPP - 2.5V Typical

• VDDSPD = 2.25V to 3.6V

• On-Die termination (ODT)

• 16 internal banks; 4 groups of 4 banks each

• Bi-Directional Differential Data Strobe

• 8 bit pre-fetch

• Burst Length (BL) switch on-the-fly BL8 or BC4(Burst Chop)

• Height 1.340” (34.04mm), w/heatsink

JEDEC/XMP TIMING PARAMETERS

• JEDEC/PnP: DDR4-2666 CL16-18-18 @1.2V

• XMP Profile #1: DDR4-2666 CL16-18-18 @1.2V

kingston.com/hyperx

Continued >>

Document No. 4808017-001.A00 06/09/17 Page 1

continued

MODULE WITH HEAT SPREADER

7.08 mm

133.35 mm

34.04 mm

MODULE DIMENSIONS

All measurements are in millimeters.

(Tolerances on all dimensions are ±0.12 unless otherwise specified)

133.35

129.55

2.10

±±0.15

3.00

Detail A

Pin 1

0.15

3.35

2.70

The product images shown are for illustration purposes only and may not be an exact representation of the product. Kingston reserves the right to change any information at anytime without notice.

28.90

Detail B Detail D Detail C

Pin 35 Pin 47

64.60

Detail E

FOR MORE INFORMATION, GO TO HYPERXGAMING.COM

All Kingston products are tested to meet our published specifications. Some motherboards or system configurations may not operate at the published HyperX memory speeds and timing settings. Kingston does not recommend that any user attempt to run their computers

the published HyperX memory speeds and timing settings. Kingston does not recommend that any user attempt to run their computers faster than the published speed. Overclocking or modifying your system timing may result in damage to computer components.

faster than the published speed. Overclocking or modifying your system timing may result in damage to computer components.

HyperX is a division of Kingston.

Pin 105 Pin 117

56.10

31.25

11.00

8.00

17.60

14.60

22.95

Document No. 4808017-001.A00 Page 2

hyperxgaming.com