HyperX HX426C15FB-4 User Manual

HX426C15FB/4

4GB 512M x 64-Bit DDR4-2666 CL15 288-Pin DIMM

SPECIFICATIONS

DESCRIPTION

HyperX HX426C15FB/4 is a 512M x 64-bit (4GB) DDR4-2666 CL15 SDRAM (Synchronous DRAM) 1Rx8, memory module, based on eight 512M x 8-bit FBGA components per module. kit supports Intel® Extreme Memory Profiles (Intel® XMP)

Each module has been tested to run at DDR4-2666 at a low

2.0. latency timing of 15-17-17 at 1.2V. are shown in the Plug-N-Play (PnP) Timing Parameters section below. The JEDEC standard electrical and mechanical specifications are as follows:

Note: The PnP feature offers a range of speed and timing options to support the widest variety of processors and chipsets. Your maximum speed will be determined by your BIOS.

Additional timing parameters

Each module

JEDEC/XMP TIMING PARAMETERS

•

JEDEC/PnP: DDR4-2666 CL15-17-17 @1.2V

DDR4-2400 CL14-16-16 @1.2V DDR4-2133 CL12-14-14 @1.2V

•XMP Profile #1: DDR4-2666 CL15-17-17 @1.2V

CL(IDD) Row Cycle Time (tRCmin) Refresh to Active/Refresh

Command Time (tRFCmin) Row Active Time (tRASmin) Maximum Operating Power UL Rating Operating Temperature Storage Temperature

*Power will vary depending on the SDRAM used.

15 cycles 45ns(min.)

260ns(min.)

26.25ns(min.) TBD W* 94 V - 0

C to +85o C

C to +100o C

-55

FEATURES

• Power Supply: VDD = 1.2V Typical

• VDDQ = 1.2V Typical

• VPP - 2.5V Typical

• VDDSPD = 2.2V to 3.6V

• Nominal and dynamic on-die termination (ODT) for data, strobe, and mask signals

• Low-power auto self refresh (LPASR)

• Data bus inversion (DBI) for data bus

• On-die VREFDQ generation and calibration

• Single-rank

• On-board I2 serial presence-detect (SPD) EEPROM

• 16 internal banks; 4 groups of 4 banks each

• Fixed burst chop (BC) of 4 and burst length (BL) of 8 via the mode register set (MRS)

• Selectable BC4 or BL8 on-the-fly (OTF)

• Fly-by topology

• Terminated control command and address bus

• Height 1.340” (34.04mm), w/heatsink

kingston.com/hyperx

Continued >>

Document No. 4807353-001.A00 07/20/15 Page 1

continued HyperX

MODULE WITH HEAT SPREADER

7.08 mm

133.35 mm

34.04 mm

MODULE DIMENSIONS

133.35

129.55

2.10±0.15

3.00

Detail A

Pin 1

0.15

3.35

2.70

28.90

Detail B Detail D Detail C

Pin 35 Pin 47

64.60

Detail E

Pin 105 Pin 117

56.10

22.95

31.25

11.00

8.00

17.60

14.60

FOR MORE INFORMATION, GO TO WWW.KINGSTON.COM/HYPERX

All Kingston products are tested to meet our published specifications. Some motherboards or system configurations may not operate at the published HyperX memory speeds and timing settings. Kingston does not recommend that any user attempt to run their computers faster than the published speed. Overclocking or modifying your system timing may result in damage to computer components.

kingston.com/hyperx

Document No. 4807353-001.A00 Page 2