HyperX HX316LC10FBK2-8 User Manual

8
8GB (4G
)
Memory Module Specifications
HX316LC10FBK2/8
HX316LC10FBK2/
8GB (4GB 512M x 64-Bit x 2 pcs.)
B 512M x 64-Bit x 2 pcs.
DDR3L-1600 CL10 240-Pin DIMM Kit
DESCRIPTION
HyperX HX316LC10FBK2/8 is kit of two 512M x 64-bit (4GB)
DDR3L-1600 CL10 SDRAM (Synchronous DRAM) 1Rx8, low
voltage, memory modules, based on eight 512M x 8-bit DDR3
FBGA components. Total kit capacity is 8GB. Each module kit
supports Intel® Extreme Memory Profiles (Intel® XMP) 2.0.
This module has been tested to run at DDR3L-1600 at a low
latency timing of 10-10-10 at 1.35V. Additional timing parame-
The JEDEC standard electrical and mechanical specifications
areas follows:
Note: The PnP feature offers a range of speed and timing options to support the widest variety of processors and chipsets. Your maximum speed will be determined by your BIOS.
PnP JEDEC TIMING PARAMETERS:
SPECIFICATIONS
selcyc 01)DDI(LC
Row Cycle Time (tRCmin) 48.125ns (min.)
Refresh to Active/Refresh 260ns (min.) Command Time (tRFCmin)
Row Active Time (tRASmin) 37.5ns (min.)
Maximum Operating Power TBD W*
0 - V 49gnitaR LU
Operating Temperature 0
Storage Temperature -55
*Power will vary depending on the SDRAM used.
o
C to 85o C
o
C to +100o C
FEATURES
JEDEC standard 1.35V and 1.5V Power Supply
VDDQ = 1.35V and 1.5V
800MHz fCK for 1600Mb/sec/pin
8 independent internal bank
Programmable CAS Latency: 11, 10, 9, 8, 7, 6
Programmable Additive Latency: 0, CL - 2, or CL - 1 clock
8-bit pre-fetch
Burst Length: 8 (Interleave without any limit, sequential with
starting address “000” only), 4 with tCCD = 4 which does not allow seamless read or write [either on the fly using A12 or MRS]
Bi-directional Differential Data Strobe
Internal(self) calibration : Internal self calibration through ZQ
pin (RZQ : 240 ohm ± 1%)
On Die Termination using ODT pin
• JEDEC/PnP: DDR3L-1600 CL10-10-10 @1.35V/1.5V DDR3L-1333 CL9-9-9 @1.35V/1.5V DDR3L-1066 CL7-7-7 @1.35V/1.5V
• XMP Profile #1: DDR3L-1600 CL10-10-10 @1.35V
hyperxgaming.com
Average Refresh Period 7.8us at lower than TCASE 85°C,
3.9us at 85°C < TCASE 95°C
Asynchronous Reset
Height 1.291” (32.80mm) w/heatsink, single sided
component
Continued >>
Document No. 4807380-001.A00 08/24/15 Page 1
continued
MODULE WITH HEAT SPREADER
MODULE DIMENSIONS
FOR MORE INFORMATION, GO TO HYPERXGAMING.COM
All Kingston products are tested to meet our published specifications. Some motherboards or system configurations may not operate at the published HyperX memory speeds and timing settings. Kingston does not recommend that any user attempt to run their computers faster than the published speed. Overclocking or modifying your system timing may result in damage to computer components.
HyperX is a division of Kingston.
©2015 Kingston Technology Corporation, 17600 Newhope Street, Fountain Valley, CA 92708 USA. All rights reserved. All trademarks and registered trademarks are the property of their respective owners.
Document No. 4807380-001.A00 Page 2
hyperxgaming.com
Loading...