HYNIX ZTA3.43MG, ZTA3.64MG, ZTA3.84MG, ZTA4.00MG, ZTB320D Datasheet
...
4-BIT SINGLE CHIP MICROCOMPUTERS
GMS34XXXT SERIES
USER`S MANUAL
• GMS34004T
• GMS34112T
• GMS34140T
Revision 1.1
Published by MCU Application Team in HYNIX Semiconductor Inc.
All Right Reserved.
Editor's E-Mail : rhja@hynix.com
Additional information of this manual may be served by HYNIX Semiconductor Inc.Offices in
Korea or Distributors and Representative listed at address directory.
HYNIX Semiconductor Inc.reserves the right to make changes to any Information here at any
time without notice.
The information, diagrams, and other data in this manual are correct and reliable; however, HYNIX
Semiconductor Inc.is in no way responsible for any violations of patents or other rights of the third
party generated by the use of this manual.
Table of Contents
Chapter 1
Introduction
Outline of Characteristics
Characteristics
Block Diagram
Pin Assignment and Terminal
Pin Dimension
Pin Description and Circuit
I/O circuit types and options
Electrical Characteristics
Chapter 2
Architecture
Block Description
Program Memory (ROM)
EPROM Address Register
Data Memory (RAM)
X-Register (X)
Y-Register (Y)
Accumulator (Acc)
Arithmetic and Logic Unit (ALU)
State Counter (SC)
Clock Generator
Pulse Generator
Initial Reset Circuit
Watch Dog Timer (WDT)
Stop Function
Port Operation
Chapter 3
Instruction
Table of Contents
............................................................................................1-1
.................................................................1-1
..................................................................................1-1
..................................................................................1-2
..........................................................1-3
..................................................................................1-4
.................................................................1-7
.............................................................1-8
................................................................1-10
...........................................................................................2-1
.............................................................................2-1
..................................................................2-1
................................................................2-2
........................................................................2-3
...................................................................................2-3
...................................................................................2-4
............................................................................2-4
.......................................................2-4
...........................................................................2-5
...............................................................................2-6
...............................................................................2-7
............................................................................2-8
.................................................................2-8
....................................................................................2-9
..................................................................................2-9
........................................................................................3-1
Table of Contents
Chapter 4
EPROM
GMS34004TK/34112TK/34140TK
Mode Define
Port Define
Programming Data
Write/Read Data Conversion
Checksum
Programming Control
Programming DC Specification
EPROM read mode(1/2)
EPROM read mode (2/2)
EPROM write mode (1/2)
EPROM write mode (2/2)
Lock bit write mode (1/2)
Lock bit write mode (2/2)
Lock bit read mode (1/2)
Lock bit read mode (2/2)
GMS34004T/112T/140T (Pin assignment & Package)
EPROM (KHz) mode
EPROM write only mode
GMS34004TK/34112TK/34140TK
Mode Define
Port Define
Programming Data
Write/Read Data Conversion
Checksum
Programming Control
Programming DC Specification
EPROM read mode(1/2)
EPROM read mode (2/2)
EPROM write mode (1/4)
EPROM write mode (2/4)
EPROM write mode (3/4)
EPROM write mode (4/4)
Lock bit write mode (1/3)
Lock bit write mode (2/3)
Lock bit write mode (3/3)
Lock bit read mode (1/2)
Lock bit read mode (2/2)
.................................................................................................4-1
.........................................................4-1
.....................................................................................4-1
.......................................................................................4-2
...........................................................................4-2
............................................................4-3
.........................................................................................4-3
........................................................................4-3
.........................................................4-3
...................................................................4-4
..................................................................4-4
..................................................................4-5
..................................................................4-5
..................................................................4-6
..................................................................4-6
..................................................................4-7
..................................................................4-7
.....................4-8
.........................................................................4-9
..................................................................4-9
.............................................................4-10
.....................................................................................4-10
........................................................................................4-11
...........................................................................4-11
............................................................4-12
........................................................................................4-12
......................................................................4-12
........................................................4-12
...................................................................4-13
...................................................................4-13
..................................................................4-14
..................................................................4-14
..................................................................4-15
..................................................................4-15
..................................................................4-16
..................................................................4-16
..................................................................4-16
..................................................................4-18
..................................................................4-18
INTRODUCTION 1
ARCHITECTURE 2
INSTRUCTION 3
EPROM 4
1 - 1
CHAPTER 1. Introduction
OUTLINE OF CHARACTERISTICS
The GMS340 series are remote control transmitter which uses CMOS technology,
and the EPROM version of GMS34XXX series.
This enables transmission code outputs of different configurations, multiple custom
code output, and double push key output for easy fabrication.
The GMS340 series are suitable for remote control of TV, VCR, FANS, Airconditioners, Audio Equipments, Toys, Games etc.
Characteristics
• Program memory : 512bytes for GMS34004T
1,024 bytes for GMS34112T/140T
• Data memory : 32 ¡¿ 4 bits
• 43 types of instruction set
• 3 levels of subroutine nesting
• 1 bit output port for a large current (REMOUT signal)
• Operating frequency :300KHz~500KHz at KHz version
2.4MHz~4MHz at MHz version
300KHz~4.2MHz at WIDE version
• Instruction cycle : f
OSC
/6 at KHz and WIDE version
f
OSC
/48 at MHz version
• CMOS process (3.0V or 5.0V power supply)
• Stop mode (Through internal instruction)
• Released stop mode by key input
• Built in capacitor for ceramic oscillation circuit at KHz version
• Built in a watch dog timer (WDT)
• Low operating voltage : 2.2~4.5V (at KHz and MHz version)
Normal operating voltage: 4.0~5.0V (at WIDE version)
Table 1-1 GMS34XXXT series members
Chapter 1. Introduction
Series
Program memory
Data memory
I/O ports
Input ports
Output ports
Package
KHz version
MHz version
WIDE version
GMS34004T
512
32 ¡¿ 4
-
4
6
D0 ~ D5
16DIP
GMS34004TK
GMS34004TM
GMS34004TW
GMS34112T
1,024
¡ç
4
¡ç
¡ç
¡ç
20DIP/SOP/SSOP
GMS34112TK
GMS34112TM
GMS34112TW
GMS34140T
¡ç
¡ç
¡ç
¡ç
10
D0 ~ D9
24DIP/SOP
GMS34140TK
GMS34140TM
GMS34140TW
1 - 2
Block Diagram
Fig 1-1 Block Diagram (In case of GMS34140T)
Chapter 1. Introduction
RAM
16word x
2page x 4bit
RAM
Word
Selector
Y-Reg
ACC
ST
R-Latch D-Latch
Pulse
Generator
X-Reg
MUX
MUX
ALU
23 22 7 8 9 4 2110 3 5 6 11 12 13 14 15 16 17 18 19 20
Instruction
Decoder
Program counter
Stack
Reset
Watchdog
timer
1 24
2
10
10
8
ROM
64word ¡¿
16page
¡¿
8bit
8
4
4
2
4 10
4
10
4
4
4
16
4
4
4
4
4
OSC1 OSC2 K0 ~ K3 R0 ~ R3 D0 ~ D9 REMOUT
RESET/Vpp VDD GND
OSC
Control Signal
1 - 3
Pin Assignment and terminals
Pin Assignment
Fig 1-2 GMS34004T Pin Assignment
(16PDIP)
Fig 1-3 GMS34112T Pin Assignment
(20DIP/SOP)
Fig 1-4 GMS34112T Pin Assignment
(20SSOP only)
Chapter 1. Introduction
Fig 1-5 GMS34140T Pin Assignment
(24DIP/SOP)
VDD
OSC1
OSC2
REMOUT
D5
D4
D3
D2
RESET/Vpp
GND
K0
K1
K2
K3
D0
D1
1
2
3
4
5
6
7
8
16
15
14
13
12
11
10
9
R3
R2
R1
R0
GND
RESET/Vpp
VDD
OSC1
OSC2
REMOUT
K0
K1
K2
K3
D0
D1
D2
D3
D4
D5
1
2
3
4
5
6
7
8
9
10
20
19
18
17
16
15
14
13
12
11
RESET/Vpp
VDD
OSC1
OSC2
REMOUT
D5
D4
D3
D2
D1
GND
R0
R1
R2
R3
K0
K1
K2
K3
D0
1
2
3
4
5
6
7
8
9
10
20
19
18
17
16
15
14
13
12
11
RESET/Vpp
GND
R0
R1
R2
R3
K0
K1
K2
K3
D0
D8
VDD
OSC1
OSC2
REMOUT
D7
D6
D5
D4
D3
D2
D1
D9
1
2
3
4
5
6
7
8
9
10
24
23
22
21
20
19
18
17
16
15
11
12
14
13
1 - 4
Pin Dimension
Fig 1-6 16PDIP Pin Dimension
1 2 3 4 5 6 7 8
16 15 14 13 12 11 10 9
0.785MAX
0.745MIN
0.040MAX
0.020MIN
0.065MAX
0.015MIN
0.140MAX
0.120MIN
¡æ ¡ç
¡æ ¡ç
0~15¡Ç
0.260MAX
0.240MIN
0.300BSC
0.014MAX
0.008MIN
Outline (Unit:Inch)
0.050MIN
0.022MAX
0.015MIN
0.100BSC
0.125MIN
0.135MAX
0.170MAX
1 2 3 4 5 6 7 8 9 10
20 19 18 17 16 15 14 13 12 11
0.984MAX
0.968MIN
0.065MAX
0.055MIN
0.022MAX
0.015MIN
0.1TYP
0.170MAX
0.015MIN
0.135MAX
0.125MIN
¡æ ¡ç
¡æ ¡ç
0~15¡Ç
0.270MAX
0.250MIN
0.3TYP
0.012MAX
0.008MIN
Outline (Unit : Inch)
Fig 1-7 20PDIP Pin Dimension
Chapter 1. Introduction
1 - 5
0.5118MAX
0.4961MIN
0.020MAX
0.014MIN
0.05TYP
0.0118MAX
0.004MIN
1 2 3 4 5 6 7 8 9 10
20 19 1 8 17 16 15 14 13 12 11
¡æ
¡ç
¡æ
¡ç
0.299MAX
0.292MIN
0.419MAX
0.0125MAX
0.0091MIN
0.104MAX
0.093MIN
0.042MAX
0.016MIN
Outline (Unit : Inch)
0.398MIN
Fig 1-8 20SOP Pin Dimension
Chapter 1. Introduction
0.344MAX
0.337MIN
0.012MAX
0.008MIN
0.025BSC
1 2 3 4 5 6 7 8 9 10
20 19 1 8 17 16 15 14 13 12 11
¡æ ¡ç
¡æ
¡ç
0.010MAX
0.007MIN
0.032MAX
0.022MIN
Outline (Unit : Inch)
Fig 1-9 20SSOP Pin Dimension
0.244MAX
0.234MIN
0.157MAX
0.150MIN
0.066MAX
0.057MIN
0.010MAX
0.004MIN
0-8¢ª
¡é
¡è
1 - 6
Chapter 1. Introduction
Fig 1-11 24SOP Pin Dimension
1 2 3 4 5 6 7 8 9 10 11
12
24 23 22 21 20 19 18 17 16 15 14
13
1.255MAX
1.245MIN
0.065MAX
0.055MIN
0.022MAX
0.015MIN
0.1TYP
0.015MIN
0.135MAX
0.125MIN
¡æ ¡ç
¡æ ¡ç
0~15¢ª
0.270MAX
0.250MIN
0.3TYP
0.012MAX
0.008MIN
Outline (Unit : Inch)
Fig 1-10 24Skinny DIP Pin Dimension
0.170MAX
0.616MAX
0.595MIN
0.020MAX
0.014MIN
0.05TYP
0.018MAX
0.004MIN
1 2 3 4 5 6 7 8 9 10 11 12
24 23 22 21 20 19 18 17 16 15 14
13
¡æ
¡ç
¡æ
¡ç
0.299MAX
0.292MIN
0.419MAX
0.398MIN
0.0125MAX
0.0091MIN
0.042MAX
0.016MIN
Outline (Unit : Inch)
0.104MAX
0.093MIN
1 - 7
Pin Function
Pin Description and Circuit
Pin Description
I/O
Connected to 2.2~4.5V power supply at KHz and MHz
version or 4.0 ~ 5.5V power supply at WIDE version.
Connected to 0V power supply.
Used to input a manual reset. When the pin goes "L",
the D-output ports and REMOUT-output port are initialized to
"L", and ROM address is set to address 0 on page 0.
For programming, this pin receives 12.5V programming
voltage.
4-bit input port.
STOP mode is released by "L" input of each pin.
The output is the structure of N-channel-open-drain.
4-bit I/O port. (Input mode is set only when each of them
output "H".)
In outputting, each can be set and reset independently(or at
once.)
The output is in the form of C-MOS.
STOP mode is released by "L" input of each pin.
High current output port.
The output is in the form of C-MOS.
The state of large current on is "H".
Oscillator input. Input to the oscillator circuit and connection
point for ceramic resonator.
Internal capacitors available at KHz version.
A feedback resistor is connected between this pin and OSC2.
Connect a resonator between this pin and OSC1.
V
DD
GND
RESET
K0~K3
D0~D9
R0~R3
REMOUT
OSC1
OSC2
Input
Input
Output
I/O
Output
Input
Output
-
-
Chapter 1. Introduction
1 - 8
I/O circuit types and options
Hysteresis Input Type.
Built in pull-up-resistor,
Typical 800
§Ú
Reset/Vpp I
Pin I/O Note
¡æ
¡ç
¡æ
¡ç
CMOS output.
"H" output at reset.
Built in MOS Tr for
pull-up about 120§Ú.
R0~R3 I/O
Built in MOS Tr for
pull-up About 120§Ú.
K0~K3 I
Open drain output.
"L" output at reset.
D0~D9
O
¡æ
¡ç
CMOS output.
"L" output at reset.
High current output
source.
REMOUT O
I/O circuit
¡ç
¡æ
¡ç
¡æ
¡ç
¡æ
¡ç
¡æ
pull-up
Chapter 1. Introduction
pull-up
1 - 9
Built in feedback-resistor
about 1
§Û
OSC2 O
Pin I/O Note
Built in resonance
Capacitor at KHz version
C1=C2 = 100pF ¡¾15%
[C1,C2 are not available
for MHz and WIDE
version]
OSC1 I
I/O circuit
Built in damping-resistor
Rd = 4
§Ú
[No resistor in MHz
operation]
¡æ
¡ç
¡æ
¡ç
¡è
¡è
OSC2
Rd
C2
Rf
C1
OSC1
STOP
Chapter 1. Introduction
Frequency Resonator Maker Part Name Load Capacitor
320KHz CQ ZTB320D C1=C2=Open
ZTB500E C1=C2=Open500KHz CQ
3.43MHz CQ ZTA3.43MG C1=C2=30pF
TDK FCR3.52M5 C1=C2=33pF
CQ ZTA3.64MG C1=C2=30pF
3.84MHz
TDK FCR3.64M5 C1=C2=33pF
CQ ZTA3.84MG C1=C2=30pF
TDK FCR3.84M5 C1=C2=33pF
CQ recommend 430KHz~500KHz resonator
3.52MHz
3.64MHz
4.00MHz CQ ZTA4.00MG C1=C2=30pF
1 - 10
Parameter
Supply Voltage
Programming Voltage
Power dissipation
Storage temperature range
Input voltage
Output voltage
Unit
V
V
mW
¡É
V
V
Electrical Characteristics
Absolute maximum ratings (Ta = 25¡É)
Symbol
V
DD
V
PP
P
D
Tstg
V
IN
V
OUT
Max. rating
-0.3 ~ 7.0
-0.3 ~ 13.5
700 *
-55 ~ 125
-0.3 ~ VDD+0.3
-0.3 ~ VDD+0.3
* Thermal derating above 25¡É : 6mW per degree ¡É rise in temperature.
Parameter
Supply Voltage
Operating temperature
Unit
V
¡É
Recommended operation condition
Rating
2.2 ~ 4.5
2.2 ~ 4.5
4.0 ~ 5.5
-20 ~ +70
Chapter 1. Introduction
Condition
300 ~ 500KHz
2.4 ~ 4MHz
300KHz ~ 4.2MHz
-
Symbol
V
DD
Topr
Loading...