Assembly & Fitting Instructions
For:
HLF060 6W LED Floodlight with PIR
HLF120 12W LED Floodlight with PIR
HLF125 12W LED DUO Dusk to Dawn Floodlight with PIR
FLOODLIGHT WITH PIR
LED SECURITY
Hylite tries to improve its products for the benefit of its
customers. For this reason we reserve the right to make
changes to any product at any time without notice.
Please note that this equipment and its components have
no user serviceable parts. If you experience any difficulties
installing this product please call our helpline or write to:
F4 Enterprises Limited
7 Abbey Square, Chester
CH1 2HU.
Tel: 01352 736120
www.f4enterprises.co.uk
TROUBLESHOOTING GUIDE
• Power not on
• Wired incorrectly
• PIR not detecting movement
• Light conditions too bright
• TIME set too high
• Wired incorrectly
• Frequent changes in heat
are being detected
• Changes in heat are being
detected from a fixed heat source
• Changes in heat are being detected
from a moving object
• Light and heat are being reflected
back onto the sensor
• Sudden temperature changes due
to storms or high winds
• Angle of PIR sensor head
is incorrect
• Sensitivity set too low
• Temperature differences are
affecting the sensitivity of the
sensor
• Turn on indoor switch or check fuse
• Check wiring is the same as wiring diagram
• Adjust the angle and direction of the PIR.
For best results walk across the beam
• Wait until light conditions are darker (at dusk
or under 40 Lux) or turn the LUX control up.
• Turn TIME control towards ‘-’ end
(10 secs to 5 min adjustable)
• Check wiring is the same as wiring diagram
• Check sensing area for possible heat sources
(e.g. air vents, moving vehicles, moving trees)
and re-position the sensor or alter the RANGE
control downwards
• Check the sensing area for air vents, light
fittings or fans and either re-position the
sensor or adjust the aim
• Check the sensing area for moving vehicles,
pedestrians, animals, moving trees and alter
the aim of the sensor accordingly
• Alter aim of the sensor or paint the reflecting
surface with a dull finish
• Turn sensor off until storm passes or install
in a sheltered location
• Adjust the PIR sensor head to alter the sensing
distance and angle
• Turn RANGE knob toward the maximum
• Turn the sensitivity (RANGE) control knob
toward the ‘+’ end for summer (hot conditions)
and toward the ‘-’ for winter (cold conditions).
This compensates for the variations in
temperature
Lights won’t come on
Lights stay on
Lights keep turning
on and off (cycling)
Sensing angle and
distance appear
incorrect
Sensor operates
differently in hot and
cold conditions
PROBLEM POSSIBLE CAUSE POSSIBLE SOLUTION
PLEASE FOLLOW THESE INSTRUCTIONS CAREFULLY BEFORE ATTEMPTING TO INSTALL AND OPERATE
THIS LIGHT.
THIS PRODUCT MUST BE INSTALLED BY A QUALIFIED ELECTRICIAN.
ALL ELECTRICAL EQUIPMENT AND APPLIANCES MUST BE CHECKED TO ENSURE THEY ARE SAFE
BEFORE OPERATING.
POWER SUPPLY LEADS, PLUGS AND ALL ELECTRICAL CONNECTIONS MUST BE REGULARLY
CHECKED TO ENSURE THEY ARE NOT LOOSE, WORN OR DAMAGED AND CIRCUITS ARE WELL
INSULATED.
WORN OR DAMAGED LEADS, PLUGS OR CONNECTIONS SHOULD NOT BE USED AND SHOULD
IMMEDIATELY BE REPLACED OR REPAIRED BY A QUALIFIED ELECTRICIAN.
THE RISK OF ELECTRIC SHOCK SHOULD BE MINIMIZED BY THE INSTALLATION OF APPROPRIATE
SAFETY DEVICES INCLUDING THE INCORPORATION OF AN RCCB (RESIDUAL CURRENT CIRCUIT
BREAKER) INTO THE MAIN DISTRIBUTION BOARD.
DO NOT WIRE THIS FLOODLIGHT INTO THE LIGHTING CIRCUIT. USE A SWITCHED FUSED SPUR (FIG.3).
CABLES SHOULD ALWAYS BE PROTECTED AGAINST SHORT CIRCUIT AND OVERLOAD.
ENSURE THE VOLTAGE MARKED ON THE PRODUCT IS THE SAME AS THE ELECTRICAL POWER SUPPLY
TO BE USED.
DO NOT PULL POWER CABLE ONCE INSTALLED AND DO NOT PULL POWER PLUGS FROM SOCKETS BY
THE POWER CABLE.
DO NOT INSTALL THE LIGHT:
- WHERE IT IS LIKELY TO BE KNOCKED OR HIT
- IN HOT OR HUMID CONDITIONS SUCH AS BATHROOMS, SHOWER ROOMS OR SAUNAS
- NEAR AN EXHAUST OUTLET E.G. BOILER FLUE, DRYER OUTLET
THE LIGHT BECOMES VERY HOT DURING USE. THEREFORE DO NOT TOUCH THE LIGHT WHEN
OPERATING, AND ALLOW TO COOL BEFORE TOUCHING.
THE LIGHT SHOULD NOT BE USED NEAR FLAMMABLE OR COMBUSTIBLE MATERIALS (SUCH AS
WOOD, CLOTH, PAPER) OR NEAR FLAMMABLE, COMBUSTIBLE OR EXPLOSIVE LIQUIDS, SOLIDS,
GASES OR EQUIPMENT.
DO NOT DIRECT THE LIGHT INTO A PERSONS EYES. THIS UNIT HAS A VERY INTENSIVE LIGHT OUTPUT,
WHICH IF INCORRECTLY USED COULD CAUSE EYE DAMAGE.
DO NOT USE THE LIGHT WITHOUT THE FRONT GLASS SHIELD. AVOID TOUCHING THE GLASS SHIELD
AS HANDLING MAY REDUCE ITS SERVICEABLE LIFE AND CAUSE THE GLASS TO CRACK.
THE MAINS POWER SUPPLY MUST BE DISCONNECTED BEFORE SERVICING OR PERFORMING ANY
MAINTENANCE.
THE LIGHT SHOULD BE MAINTAINED IN GOOD CONDITION WITH REPAIR ONLY BE UNDERTAKEN BY A
QUALIFIED ELECTRICIAN.
REPAIRS SHOULD ONLY BE CARRIED OUT USING GENUINE PARTS. NON-AUTHORIZED PARTS MAY BE
DANGEROUS AND WILL INVALIDATE THE WARRANTY.
IMPORTANT SAFETY INSTRUCTIONS
IMPORTANT INSTALLATION INSTRUCTIONS
IMPORTANT OPERATION AND MAINTENANCE INSTRUCTIONS
1 x LED floodlight with PIR and mounting bracket
1 x Fixing kit (4 x wall plugs, 4 x No.8 masonry screws)
1 x Instruction manual (please keep safe for future reference)
• Electric / hand-held drill
• No.8 masonry drill bit
• Electricians screwdriver
• Large screwdriver
• Wire cutters
This product is suitable for wall mounting.
PARTS INCLUDED
TOOLS REQUIRED
TECHNICAL SPECIFICATION
230V AC - 50Hz
6W LED
8-10 Metres
@15-20ºC
120º
15 secs - 5 mins
Day/Night or Night
Only opertation
IP44
6W
Power Supply
LED Light
Detection Range
Detection Angle
Time On Adjustment
Dusk Level Adjustment
Environment Protection
Power
HLL060
6W LED Floodlight
with PIR
230V AC - 50Hz
12W LED
8-10 Metres
@15-20ºC
120º
15 secs - 5 mins
Day/Night or Night
Only opertation
IP44
12W
HLL120
12W LED Floodlight
with PIR
230V AC - 50Hz
12W LED
8-10 Metres
@15-20ºC
120º
15 secs - 5 mins
Day/Night or Night Only
opertation
IP44
12W (on PIR detection)
6W (Dusk till Dawn)
HLL125
12W DUO Dusk till dawn
LED Floodlight with PIR
• Mount the floodlight onto solid brickwork, 3 - 5m above the ground (Fig. 1).
• The sensor should be mounted horizontal to ensure the
detection area is maximized by being even from side to side.
• Installation under eaves is acceptable but radiated and
convected heat from the fitting must be taken into account.
• Avoid pointing the PIR sensor at trees & shrubs,
hot ventilator ducts, air conditioners street lighting
or traffic which may interfere with its operation.
• Do not allow sunlight to fall directly onto the front
of the PIR sensor, otherwise poor triggering response
may occur.
• Prior to mounting, keep in mind that the PIR sensor
is more sensitive to a heat source moving across
its coverage area and less sensitive to a heat source
that moves directly towards the PIR sensor (Fig.2).
CHOOSING A MOUNTING LOCATION
3 - 5m
Fig.1
Fig.2
Less sensitive More sensitive
PIR
sensor
• Unscrew the nut from the mounting bracket and remove the bracket from the floodlight.
• Use the bracket to mark the drill hole and the cable outlet location.
• Drill the wall and screw the bracket onto the wall
using the wall plugs and screws provided (Fig.3).
• Re-attach the floodlight to the bracket and secure the cable
(and additional lighting load supply cable if applicable)
to the wall using suitable clips.
• Ensure that the cable is not touching the body of the
floodlight, and that there is sufficient slack in the cable
to allow the floodlight to be tilted and adjusted as required.
NB: Tilt and adjust the floodlight by grasping the metal body of the floodlight,
not the wiring box.
MOUNTING INSTRUCTIONS
Fig.3
WARNING: Isolate the power supply before installation.
• The unit requires connection to a 220-240 AC 50Hz mains electricity supply.
• It is recommended that the unit is connected
to the domestic lighting circuit via a 5 amp
fused spur and using 3-core round
flexible cable of at least
1mm2 gauge (Fig. 4).
• It is also advisable to install a single pole wall
switch to allow easy control of the floodlight.
• Prior to installing the floodlight the cable
gland needs to be attached by undoing the
four screws from the wiring box, removing
the cover (Fig.5) and fitting the gland to the
wiring box, as shown in (Fig.6).
• The AC cable should then be routed through
the cable gland as shown in (Fig.7).
• To connect, strip approximately 6mm of
insulation from each of the 3 cores of the
AC cable and:
- Connect the wire coloured BROWN or RED (Live)
to the corresponding BROWN wire in the terminal block,
or the terminal marked “L”
- Connect the wire coloured BLUE or BLACK (Neutral)
to the corresponding BLUE wire in the terminal block,
or the terminal marked “N”
- Connect the wire coloured YELLOW/GREEN
(Earth wire) to the corresponding YELLOW/GREEN
terminal block marked (Fig.8).
• Finally, gently tighten up the nut against
the gland body, to ensure the wire is secured
in place by the sealing gland (Fig.7).
3 amp fuse
To the
lamp
From
mains
supply
Double-pole switched fused spur
INSTALLATION WIRING INSTRUCTIONS
Fig.4
Fig.8
Fig.5
Fig.7
Fig.6
Remove
junction
box screws
Sealing gland
• The RANGE sensitivity of the PIR is affected by the range of detection and the amount of
infra-red radiation (heat) required to trigger the sensor.
• The RANGE sensitivity adjustment can also be used to compensate for the changes in outside
air temperature in winter and summer.
• To be effective but keep nuisance tripping to a minimum it is advised to turn the RANGE
control to the middle position where the ambient air temperature is between 15°–20°C.
In addition to statutory rights, Hylite LED Security Floodlights carry a full 5 year warranty
against manufacturing failure, so long as installation, operation and maintenance has been
carried out in accordance with the instructions contained in this booklet. All returns are
subject to a £15 handling charge.
RANGE SETTING
5 YEAR WARRANTY
1. For DAYTIME testing:
• Turn the TIME control
(length of time light switches on)
to minimum and the LUX
(ambient light level) control to maximum.
• Turn on the power to the floodlight.
• The floodlight will turn on for approx.
15 seconds before switching OFF.
For NIGHTTIME testing:
• Turn the TIME control (length of time light switches on) to minimum and the LUX
(ambient light level) control to minimum.
• Turn on the power to the floodlight.
• The floodlight will turn on for approx. 15 seconds before switching OFF.
2. Check the operation of the sensor and the field of view by walking in front of the floodlight
so that the light comes on.
3. Once the light comes on, move to a new position and stand still until the light goes out
(approx. 15 sec), move again until the light comes on.
4. Repeat step 3 and adjust the angle of the sensor head until the optimum field of view
is achieved.
5. Finally, turn the TIME, LUX and RANGE (to alter detection range of PIR) controls to the
desired positions for AUTO operation..
FIRST TIME POWER UP
Fig.9
• The TIME control should be turned up if the lights are required to switch on for longer.
• Time is adjustable between approximately 15 seconds to 5 minutes.
• If a moving heat source is detected, the sensor is triggered, switching on the light and
beginning timing out according to the pre-set TIME period. If triggered further, the light
will stay on for the pre-set time period from the last trigger.
• The ideal ON time for general domestic situations is usually 2-3 minutes.
TIME SETTING
• The LUX setting adjusts how low the light level needs to go down to (level of darkness)
before the light operates.
• For the standard floodlights with PIR, the LUX control adjusts the light level at which the
light and PIR operate. For the DUO, dusk-to-dawn model, the LUX level adjusts the light level
at which the floodlight will operate in its dimmed-down mode, increasing to full power when
activated by the PIR.
LUX SETTING
Loading...