Page 1
Important - Please read these instructions fully before starting assembly
Dimensions
Issue 1 - 9/04/11
Width - 115cm
Depth - 55cm
Height - 75cm
Matrix Desk
Assembly Instructions - Please keep for future reference
619/1645
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
619/1638
Page 2
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household waste.
Take to your local authority
waste disposal centre.
Safety and Care Advice
• This product complies with
BS EN 12521: 2009.
• Imported by:
Home Retail Group.
489-499 Avebury Boulevard.
Saxon Gate West.
Central Milton Keynes.
MK9 2NW
• Product Cat no.:619/1645(D) (Clear Glass)
Cat no.:619/1638(D) (Black Glass)
• P/O No:
• If the glass is chipped or broken, stop using the product and
consult the Manufacturer or Supplier.
Warnings
a) Do not place very hot or very cold items on the glass surface(s) unless adequately thick table mats
are used to prevent such items from coming into contact with the glass.
b) Do not sit or stand upon the glass surface(s).
c) Do not use the glass as a chopping surface. Do not strike the glass with hard or pointed items.
d) When cleaning glass panels use a damp cloth or leather with washing up liquid or soft soap if
necessary, do not use washing powders or any other substance containing abrasives since these
substances scratch glass.
Important – Please read these instructions fully before starting assembly
Glass safety
Care and maintenance
1
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put excessive
weight on the product, this
could cause damage.
• Assemble the item as close
to its final position (in the same
room) as possible.
• Parts of the assembly will be
easier with 2 people.
• Dispose of all packaging
carefully and responsibly.
• Place the product on flat and
steady surface during use.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor.
• Keep these instructions for
further use.
• To ensure an easier assembly,
we strongly advise that all
fittings are only finger tightened
during initial assembly. Only
upon completion of the
assembly should all fixing points
be fully tightened.
Page 3
Please check you have all the parts listed below
Components - Parts
2
1
Glass top (115 x 55 cm)
3
Leg x 2 (73 x 5 cm)
If you have damaged or missing components,
call the Customer Helpline: 08456 400800
5
4
6
2
Glass shelf x 2
(53.9 x 42.5 cm)
Support (Long) x 4 (48 x 5cm) (Plastic caps both ends)
Support (Short) x 4 (16.5 x 5cm) (Plastic cap one end only)
Feet x 4 (7.6 x 5cm) (Plastic cap one end only)
Page 4
Please check you have all the fittings listed below
Components - Fittings
3
If you have damaged or missing components,
call the Customer Helpline: 08456 400800
Note: The quantities below are the correct amount to complete the assembly. In some cases more
fittings may be supplied than are required.
A
720mm Threaded stud x 6
C
F
Spanner x 1
Ruler - Use this ruler to help correctly identify the screws
0
5
10 15 20 25 30 35 40
45
50
55
60 65 70
75
80 85 90 95 100 105 110 115 120 125 130 135 140 145 150 155 160 165 170
Tools required
0
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 105110 115 120 125130 135 140145 150
1 2 3 4 5 6
Ruler/tape
measure
E
Box spanner x 1
B
D
Nut x 12
Spring washer x 6
End cap x 6
Page 5
4
Step 1
Step 2
Assembly Instructions
a:
A
B
A
A
B
F
b:
1
Attaching threaded rod
Warning:
With help,
carefully p
lace
glass top upside
down onto a clean flat
surface.
a: Screw nuts onto
the ends of threaded
rods .
b: Screw threaded rods
into the metal discs on
the underside of glass
top .
Use spanner to fully
tighten nuts down
onto the metal discs.
A
1
1
F
B
A
B
Locate legs over
threaded rods on one
side of top .
Note: Ensure the metal
plates welded inside the
ends of legs are
facing upwards.
Using box spanner ,
fully tighten fixings and
to secure the legs.
Fit end caps .
Attaching legs
E
D
3
A
B
C
3
1
1
330mm
B
700mm
A
Metal plate
facing up.
B
C
3
D
E
3
A
B
C
Page 6
Assembly Instructions
5
Step 3
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Home Retail Group. 489-499 Avebury Boulevard. Saxon Gate West. Central Milton Keynes. MK9 2NW
Metal plate
facing up.
B
C
6
Step 4
2
4
A
Locate short supports
over threaded rods .
Note: Ensure the plastic
caps in the ends of
supports are facing up.
Warning:
Carefully locate
glass shelf
over the threaded rods .
4
4
A
2
A
Locating middle glass
shelf
Plastic caps
to face up
Locate long supports
over threaded rods .
Warning:
Carefully locate
glass shelf
over the threaded rods .
Locate feet over the
threaded rods.
Note: Ensure the metal
plates welded inside the
ends of feet are facing
upwards.
Using box spanner ,
fully tighten fixings and
to secure the feet.
Fit end caps .
With help, carefully turn
the desk upright.
Warning:
The desk is heavy.
Lift with care.
Locating lower glass shelf
D
A
C
B
5
2
A
6
6
Assembly is complete.
E
D
E
6
B
C
Page 7
619/1638
Insert Additional Pages If Required.
Page 8
Insert Additional Pages If Required.
Page 9
(8x5cm)
(16x5cm)
Page 10
Plastic cap 16pcs
Metal plate threaded 6pcs
Page 11
a
A
Screw metal plates threaded
C into threaded rods A
Insert Additional Pages If Required.
Insert Additional Pages If Required.
Page 12
Loading...