Hygena HD-5317T Instruction manual

Amparo 4 Chairs
Assembly Instructions - Please keep for future reference
Dimensions
Width - 58cm
Depth - 49cm
Height - 75cm
Important – Please read these instructions fully before starting assembly
If you need help or have damaged or missing part s, call the Customer Helpline:
Argos = 0345 6400800
Issue 4 - 7/09/16
Safety and Care Advice
Important – Please read these instructions fully before starting assembly
• Check you have all the
components and tools listed on the following pages.
• Remove all fi ttings from the plastic bags and separate them into their groups.
• Keep children and animals away from the work area, small parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before starting.
Care and maintenance
• Only clean using a damp cloth and mild detergent, do no use
bleach or abrasive cleaners.
• During assembly do not stand or put weight on the product,
this could cause damage.
Assemble the item as close to its fi nal position (in the same room) as possible.
Assemble on a soft level surface to avoid damaging the unit or your fl oor.
• Parts of the assembly will be
easier with 2 people.
• From time to time check that there are no loose screws on this unit.
To reduce the likelihood of
damaging your product please
ensure that your power drill is set on a low torque setting.
• Do not stand on the chair.
• Do not use this chair as a step
ladder.
• Maximun safe weight of user: 110kgs.
This product should not be
discarded with household waste. Take to your local authority waste disposal centre.
Handy Hints
Assemble all parts and bolts loosely during assembly, only once the product is complete should you fully tighten the bolts
• Regularly check and ensure that all bolts and fi ttings are tightend properly.
1
If you have damaged or missing components, call the
Components - Panels
Customer Helpline: Argos = 0345 6400800
Please check you have all the panels listed below
The quantities below are for 4 chairs
1 Chair back x 4
(54.2 x 34.7 cm)
4 Chair leg x 4
(57.7 x 42.9 cm )
2 Chair seat x 4
(52.6 x 39.5 cm)
3 Chair leg x 4
(48.8 x 43.2 cm)
2
Components - Fittings
Please check you have all thettings listed below
Note: The quantities below are the correct amount to complete the assembly of 4 chairs. In some cases more ttings may be supplied than are required.
A
64mm Bolt x 16 32mm Bolt x 16
D E
Nut x 4
G
Curved washer x 20
J
Wrench x 1
B
Insert nut x 16
H
Spring washer x 36
K
Hex key x 1
(supplied in the fittings pack of table)
Tools required
Flatblade screwdriver
C
28mm Bolt x 4
F
Plain washer x 16
I
Bolt cap x 16
Ruler - Use this ruler to help correctly identify the screws
105
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100
110 115 120 125 130 135 140 145 150 155 160 165 170
3
Assembly Instructions
Step 1
Assemble legs
3
Assemble chair leg
4
and curved washer , spring
washer and nut .
using bolt C,
G
H
D
Note: Do not fully tighten the bolts.
C
4
G
H
D
3
Step 2
Assemble seat and back
Two people are needed here
a: Place chair seat upside down, put insert
E
nuts
into the holes on the underside of the seat, make sure the threaded hole of the insert nut is aligned with the holes in the edge of the chair seat
as shown in the figure.
2
a:
E
2
E
E
E
Continued on next page.
4
Assembly Instructions
Step 2 - continued
b:
b: Assemble chair back
1
to the seat using
A
bolts
H
, and secure tightly by using hex key
Note: Use a screwdriver to turn the insert nut slightly as shown in the
figure if the bolt could not
screw in.
, spring washers
and plain washers
K
.
F
2
Step 3
Assemble legs
Fix the chair legs to the seat using bolts , spring washers and curved washers .
Note: Re-tighten all the bolts and nuts.
B
H
G
F
H
A
1
B
H
G
5
Assembly Instructions
Step 4
Assemble bolt cap
Turn the chair to back to its up- right position, then cover the bolts on the back of the chair with bolt caps
Assembly is complete.
I
.
I
I
I
I
If you need help or have damaged or missing parts, call the Customer Helpline:
Argos = 0345 6400800
Loading...