Page 1
Hygena Cubic Wood/Glass Coffee/Nest
Assembly Instructions - Please keep for future reference 453/1939D
Dimensions
Width - 95cm
Depth - 48cm
Height - 45.6cm
Important – Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline: 03456 400800
Issue 1 - 16/09/15
Page 2
Safety and Care Advice
Important – Please read these instructions fully before starting assembly
• Check you have all the
components and tools listed on
pages 2 & 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close
to its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor.
• Parts of the assembly will be
easier with 2 people.
as this could damage the unit.
Only use hand screwdrivers.
• Dispose of all packaging
carefully and responsibly.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
Glass safety – Take care when handling glass, please follow the advice below
• •
•
If a glass component is
chipped or broken replace with
glass of the type described on
this instructions. Consult the
manufacturer, retailer or agent
with regard to obtaining a
manufacturing specification and
shape for replacement glass
quoting the model number, and
batch or date of manufacture.
Do not place very hot or
cold items against or in close
proximity to the glass
surfaces unless adequately
thick insulating material is
used to prevent such items
coming into contact with the
glass.
•
Do not strike the glass with
hard or pointed items.
When cleaning glass panels
or mirrors use a damp cloth or
leather with washing up liquid or
soft soap if necessary.
•
Do not use washing powders
or any other substances
containing abrasives since these
substances scratch glass.
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Note: if require the next
page can be cut out and used
as reference throughout the
assembly. Keep this page with
these instructions for future
reference.
1
Page 3
Components - Panels
Please check you have all the panels listed below
Large table
1
side frame x 2
(476 x 435 mm)
Long bolt x 4
4
(438 x 7mm)
Small table
7
top panel x 2
(350 x 350 mm)
Large table
2
cross bar x 2
(825 x 58mm)
Small table
5
side frame x 4
(347 x 346 mm)
Short bolt x 8
8
(350 x 7mm)
Large table
3
top panel
(950 x 480 mm)
Small table
6
cross bar x 4
(225 x 58mm)
2
Page 4
If you have damaged or missing components,
A
D
Metal dowel
x
12
G
Components - Fittings
call the Customer Helpline: 03456 400800
Please check you have all the fittings listed below
Note: The quantities below are the correct amount to complete the assembly. In some cases more
fittings may be supplied than are required.
B C
Wood dowel x 12
Metal cam x 12
Foot pad x 12
Tools required
E
Nut x 12
Phillips screwdriver
(medium & small)
Wrench
(Provided)
Wrench x 1
F
Washer x 12
Flatblade screwdriver
3
Page 5
Assembly Instructions
Step
1
Lay Large table side
frames on a flat soft
1
surface.
Insert Wood dowels
A
into the indicated holes.
Screw 4 Metal dowels
C
into the threaded holes
in the Large table side
frames as shown.
1
C
A
C
A
C
1
1
A
A
C
Step 2
Firmly push the Large
table side frames
onto the ends of Large
table cross bars ,
ensuring the Metal
dowels and Wood
dowels enter
C
A
corresponding holes.
1
2
1
1
2
2
4
Page 6
Assembly Instructions
Step
3
Insert the 4 Metal Cams
D
into the 4 holes on
the Cross bars and
push in firmly.
Note: Longer
leg of the cross
on the Metal
Cams must face towards
metal cams (as shown).
Then, using a Philips
Screwdriver, screw all 4
Metal Cams
clockwise until they are
‘ hand tight’.
2
D
Note: Longer leg of
the cross on the
Metal Cams must
face towards metal
cams.
D
Step 4
Lay the Large table top
panel upside down
on a soft surface.
Screw end of bolts
into the hole of the
blocks on the Large
table top panel
firmly.
3
4
3
4
3
5
Page 7
Step
Assembly Instructions
5
Firmly place the unit
from Step 3 onto the
Bolts .
Put one Washer onto
each bolt head, screw
Nut on the head of
bolt, tighten with
Wrench .
before tightening.
4
F
E
B
Note: Align
legs with
metal blocks
B
E
F
4
3
Step 6
Peel off the cover of the
Foot pad , attach to
the end of Large table
side frames as
shown.
Turn the table upright.
F
1
F
6
Page 8
Step
Assembly Instructions
7
Repeat Step 1 - 6 to
assemble the other 2
small tables with Side
frames , Cross
bars , Top panels
and Bolts .
5
6
8
7
5
5
6
6
8
7
Assembly is complete.
If you need help or have damaged or missing parts, call the Customer Help Line: 03456 400800
Home Retail Group plc. Avebury, 489-499 Avebury Boulevard. Milton Keynes. MK9 2NW
7
Loading...