Hygena BQ099-585 Instruction manual

Floor Cabinet

Assembly Instructions- please keep for future reference

833/4455

Dimensions

Width - 35cm

Depth - 30cm

Height - 90.5cm

Important – Please read these instructions fully before starting assembly

If you need help or have damaged or missing parts, call the Customer Helpline: 0845 640 0800

Issue 1 - 21/04/11

Safety and Care Advice

Important – Please read these instructions fully before starting assembly

• Check you have all the components and tools listed on pages 1 and 2.

• Remove all ttings from the plastic bags and separate them into their groups.

• Keep children and animals away from the work area, small parts could choke if swallowed.

• Make sure you have enough space to layout the parts before starting.

Care and maintenance

• Only clean using a damp cloth and mild detergent, do not use bleach or abrasive cleaners.

• Do not stand or put weight on the product, this could cause damage.

• Assemble the item as close to its nal position (in the same room) as possible.

• Assemble on a soft level surface to avoid damaging the unit or your oor.

• Parts of the assembly will be easier with 2 people.

• From time to time check that there are no loose screws on this unit.

• We do not recommend the use of power drill/drivers for inserting screws,

as this could damage the unit. Only use hand screwdrivers.

• Dispose of all packaging

carefully and responsibly.

• This product should not be discarded with household waste. Take to your local authority waste disposal centre.

Components - Panels

Please check you have all the panels listed below

Top x 1

1

(35(w)cm x 30(d)cm)

Base x 1

4

(29(w)cm x 28.5(d)cm)

Left side x 1

2

(89(h)cm x 28.5(d)cm)

Back panel x 1

5

(80.5(h)cm x 31(w)cm)

Right side x 1

3

(89(h)cm x 28.5(d)cm)

Door x 1

6

(78(h)cm x 28.5(w)cm)

Shelf x 2

7

(30(w)cm x 26(d)cm)

1

If you have damaged or missing components,

Components - Fittings

call the Customer Helpline: 0845 640 0800

Please check you have all the ttings listed below

Note: The quantities below are the correct amount to complete the assembly. In some cases more ttings may be supplied than are required.

A

B

C

D

35mm Male camlock x 8 Female camlock x 8 30mm Wooden dowel x 2 Magnetic catch x 1

E

14mm Screw x 2 Hinge x 2 10mm Screw x 9 Magnetic catch plate x 1

I

16mm Screw x 2 Handle x 1 Shelf bracket x 8 Safety strap x 1

M

F

N

J

G

K

O

H

P

L

10mm Screw x 1 Back panel screw x 12 35mm Screw x 1 Washer x 1

Q

Rawl plug x 1

Tools required

Phillips screwdriver (medium & large)

Drill (for wall drilling only)

Ruler – Use this ruler to help correctly identify the screws

105

0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100

110 115 120 125 130 135 140 145 150 155 160 165 170

2

Using Camlocks

Step 1

Connect the male camlock as directed in the assembly instructions using a screwdriver.

Step 2

Insert the female camlock as shown in the instructions.

Note: ensure that the arrow on the top of the camlock points towards the entry hole for the male camlock.

Assembly Instructions

Step 1

Fix 4 x 35mm male camlock 30mm wooden dowel into underside of top as shown.

A

and 2 x

C

1

Step 3

Push the male camlock into the entry hole.

Step 4

Turn the female camlock clockwise with a screwdriver.

You should feel a click when the camlock is locked in place.

The joint is now secure.

M

L

a:

A

Connect safety strap to underside of top using 1 x 10mm screw

M

as shown (a:).

Connect magnetic catch

D

to underside of top

1

using 2 x 14mm

screw

E

as shown (b:).

L

1

Step 2

Insert 4 x female camlock underside of base shown.

B

into

4

as

1

C

E

b:

B

4

D

3

Assembly Instructions

Step 3

Screw 2 x male camlock

Fix 2 x female camlock

A

B

into reverse of drawer

and 2 x 35mm male

13

front

camlock

2

and right side 3 as

shown.

A

as shown.

into left side

B

2

A

3

Step 4

Connect hinges B to top door door screws

Step 4

Connect base 4 to right side shown and tighten the female camlocks in the underside of base with a screwdriver.

Note: the groove in base

4

must line up to the groove in right side (i.e. to the rear of the unit).

5

and bottom

6

using 15mm

F

as shown.

3

as

4

3

Step 5

3

4

2

Insert 4 x 15mm female

Step 5

camlock side of top base

Connect left side shown.

2

to base 4 as shown and tighten the

Insert 4 x small wooden female camlocks in the

dowel underside of base

9

as shown. with a screwdriver.

4

E

into under

7

D

into top shelf

as

4

Assembly Instructions

Step 6

Connect top base 7

Connect top 1 to left and top shelf

and right sides as shown and tighten the female

right side camlocks inside the unit

Tighten female camlocks with a screwdriver.

in under side of top base

7

Note: the groove in top

with a screwdriver. must line up with the grooves in the left and right sides (i.e. to the rear of the unit).

9

to top

2

.

1

Step 7

Connect top left side to exposed ends of top base

Tighten female camlocks in under side of top base

7

and top shelf

9

as shown

7

with a screwdriver.

1

Step 8 Step 7

Screw 4 x male camlock

A

into the under side of

Connect back panel

10

top to the rear of the unit as

shown using 12 x back panel screw

Note: ensure the safety strap sticks through the hole in the back panel to enable securing to a wall

Connect top 10 as

(see Step 10). shown.

as shown.

Step 9

N

.

5

N

Tighten female camlocks with a screwdriver.

5