Hygena BQ099-584 Instruction manual

Wall Cabinet
Assembly Instructions- please keep for future reference
833/4431
Dimensions
Width - 30cm
Depth - 15cm
Height - 50cm
Important – Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline: 0845 640 0800
Safety and Care Advice
Important – Please read these instructions fully before starting assembly
• Check you have all the components and tools listed on pages 1 and 2.
• Remove all ttings from the plastic bags and separate them into their groups.
• Keep children and animals away from the work area, small parts could choke if swallowed.
• Make sure you have enough space to layout the parts before starting.
Care and maintenance
• Only clean using a damp cloth and mild detergent, do not use bleach or abrasive cleaners.
• Do not stand or put weight on the product, this could cause damage.
• Assemble the item as close to its nal position (in the same room) as possible.
• Assemble on a soft level surface to avoid damaging the unit or your oor.
• Parts of the assembly will be easier with 2 people.
• From time to time check that there are no loose screws on this unit.
• We do not recommend the use of power drill/drivers for inserting screws,
as this could damage the unit. Only use hand screwdrivers.
• Dispose of all packaging
carefully and responsibly.
• This product should not be discarded with household waste. Take to your local authority waste disposal centre.
Components - Panels
Please check you have all the panels listed below
Top x 1
1
(30(w)cm x 15(d)cm)
Left side x 1
4
(47(h)cm x 13.5(d)cm)
Base x 1
2
(27(w)cm x 13.5(d)cm)
Support rail x 1
5
(24(w)cm x 6(h)cm)
Right side x 1
3
(47(h)cm x 13.5(d)cm)
Back panel x 1
6
(47.8(h)cm x 24.8(w)cm)
Door x 1
7
(46.5(h)cm x 23.5(w)cm)
Shelf x 1
8
(23.8(w)cm x 9.8(d)cm)
1
If you have damaged or missing components,
Components - Fittings
call the Customer Helpline: 0845 640 0800
Please check you have all the ttings listed below
Note: The quantities below are the correct amount to complete the assembly. In some cases more ttings may be supplied than are required.
A
B
C
D
35mm Male camlock x 8 Female camlock x 8 16mm Bolt x 2 Handle x 1
E
14mm Screw x 2 Magnetic catch x 1 10mm Screw x 9 Hinge x 2
I
30mm Wooden dowel x 4 Catch plate x 1 Shelf bracket x 4 40mm Wall screw x 2
M
F
N
J
G
K
H
L
Washer x 2 Rawl plug x 2
Tools required
Phillips screwdriver (medium & large)
Drill (for wall drilling only)
Ruler – Use this ruler to help correctly identify the screws
105
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100
110 115 120 125 130 135 140 145 150 155 160 165 170
Spirit level
2
Using Camlocks
Step 1
Connect the male camlock as directed in the assembly instructions using a screwdriver.
Step 2
Insert the female camlock as shown in the instructions.
Note: ensure that the arrow on the top of the camlock points towards the entry hole for the male camlock.
Assembly Instructions
Step 3
Push the male camlock into the entry hole.
Step 4
Turn the female camlock clockwise with a screwdriver.
You should feel a click when the camlock is locked in place.
The joint is now secure.
Step 1
Fix 4 x 35mm male camlock underside of top shown.
Connect magnetic catch
F
to underside of top
1
using 2 x 14mm
screw
A
into
1
E
as shown (a:).
as
Step 2
A
1
E
a:
F
A
Fix 4 x 35mm male camlock shown.
A
base
2
as
2
3
Assembly Instructions
Assembly Instructions
Step 3
Step 3
Screw 2 x male camlock
Insert 2 x 30mm wooden
A
dowel front
of support rail shown.
I
into reverse of drawer
into each end
13
as shown.
5
as
I
5
Step 4
Insert 4 x female camlock
Step 4
side as shown.
Connect hinges B to top door door screws
B
into right
3
and left side 4
5
and bottom
6
using 15mm
F
as shown.
Step 5
Connect left side
4
and right side 3 to support rail shown.
5
as
B
4
4
3
Note: the unit is upside
Step 5
down at this point. Insert 4 x 15mm female
camlock side of top base shown.
Insert 4 x small wooden dowel
9
as shown.
4
E
into under
7
D
into top shelf
3
as
5
Assembly Instructions
Assembly Instructions
Step 6
Step 6
Connect top base 7
Connect top 1 to and top shelf
assembly completed at Step 5 as shown
right side and tighten the female
Tighten female camlocks camlocks inside the unit
in under side of top base with a screwdriver.
7
with a screwdriver.
9
to top
2
.
Step 7
6
Slide back panel
Step 7
the slots of left and right Connect top left side
sides and push rmly to exposed ends of top
down to locate. base
Note: the holes in the back panel should point
Tighten female camlocks
downwards at this stage in under side of top base
and should line up with the holes in support rail
fully inserted.
7
and top shelf
9
as shown
7
with a screwdriver.
5
when back panel is
into
1
Step 8
Screw 4 x male camlock
A
into the under side of
10
top
as shown.
Step 8
Connect base 2 to the assembly as shown and tighten the female
Step 9
camlocks inside the unit with a screwdriver.
Connect top 10 as Turn the unit right way
shown. up to complete the
Tighten female camlocks remaining steps.
with a screwdriver.
1
6
2
5
5
Loading...
+ 14 hidden pages