Hygena BERGEN 2DRW INTERNAL Instruction manual

Bergen 2 drawer internal chest 120

Assembly Instructions- Please keep for future reference 246/7287

DR8250120

Dimensions

Tip : To prevent damage,

Width - 40cm

Depth - 38.7cm

Height - 40.1cm

we recommend that you

build your unit on the

carton(s) it was packed in.

Important – Please read these instructions fully before starting assembly

If you need help or have damaged or missing parts, please visit: www.argos-support.co.uk
or email: [e-mail] (quoting your original order number)
Alternatively, call the Spares Helpline on: 0370 112 1928
For any other queries please contact the Customer Helpline on: 0345 640 2020

Issue 4 - 11/01/16

Safety and Care Advice

Important – Please read these instructions fully before starting assembly

• Check you have all the
components and tools listed on
the following pages.

plastic bags and separate them
into their groups.

• Keep children and animals
away from the work area, small
parts could choke if swallowed.

• Make sure you have enough
space to layout the parts before
starting.

• During assembly do not stand
or put weight on the product,
this could cause damage.

• Assemble the item as close

room) as possible.

• Assemble on a soft level
surface to avoid damaging the

• Parts of the assembly will be
easier with 2 people.

power drill is set on a low torque
setting.

Glue safety - Take care when using glue, please follow the advice below

Skin contact: Remove

contamination by washing with
soap and water. This procedure
should also be followed prior to
eating and drinking.

Eye contact: Rinse immediately
with clean water for 15 minutes
and seek medical advice.

If swallowed: Seek medical
advice immediately.

• To reduce
the likelihood of
damaging your
product please
ensure that your

Care and maintenance

• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.

Handy Hints

• Assemble all parts and bolts
loosely during assembly, only
once the product is complete
should you fully tighten the bolts

• From time to time check that
there are no loose screws on
this unit.

• Regularly check and ensure

tightend properly.

• This product should not be
discarded with household waste.
Take to your local authority
waste disposal centre.

Note: if required the next
page can be cut out and used
as reference throughout the
assembly. Keep this page with
these instructions for future
reference.

2

For damaged or missing parts, please visit:

Components - Panels

www.argos-support.co.uk or email: [e-mail]

Please check you have all the panels listed below

Left side

1

(38.6 x 37cm)

P2878

Drawerfront x 2

4

(38 x 15.7cm)

P4469

Left Drawer Side x 2

7

(35 x 12cm)

LA163709

Right side

2

(38.6 x 37cm)

P2877

Plinth

5

(36.7 x 6cm)

P7029

Right Drawer Side x 2

8

(35 x 12cm)

LA163809

Top

3

(40 x 38.7cm)

P1645

Drawer Back x 2

6

(33.3 x 12cm)

LA163609

Drawer Base x 2

10

(34.3 x 34.3cm)

BO352909

Folded Back

9

(39.3 x 39.3cm)

BO343209

3

105

Components - Fittings

For damaged or missing parts, please visit:
www.argos-support.co.uk or email: [e-mail]

Please check you have all the fittings listed below

Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings
may be supplied than are required.

1/1

FK1012

A

B

15mm

Large locking nut x 4 (15x12mm) Small locking nut x 4 (12x10mm)

D

10mm Fixing screw drawer x 8

G

9mm Screw x 4

J

Glue x 1

Locking screw x 8

FK1301

E

Wood dowel x 4

FK1981

H

Nail holder x 1

FA1510

K

Furniture glide x 4

(5x24mm)

(8x30mm)

FK1011

C

FK1411

F

Nail x 30

FK1415

I

Drawerbase support x 8

FK1233

L

Runner x 4

12mm

FK1010

FK1515

FK1250

PM16951

Tools required

Phillips screwdriver

(medium & large)

Flatblade screwdriver

(medium)

Setsquare

Ruler - Use this ruler to help correctly identify the screws

0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100

4

The screws length is measured from the head to the point (30mm screw shown).

Small
hammer

0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150

0 1 2 3 4 5 6

Ruler/tape
measure

Scissors

Eye protection
(when using a
hammer or drill)

110 115 120 125 130 135 140 145 150 155 160 165 170

Assembly Instructions

C

C

7810J6

4

C

Step 1

Prepare the locking
screws

a:

Screw 2 metal dowelsB
into the holes shown on
the back of each drawer
front 4 .

Note: Tighten metal

dowels
up fully against the panels.

2x

b: Prepare the drawer

sides

Insert a small locking nut
C
into the hole on left drawer
side 7 and right
drawerside 8.
Make sure the ‘arrow’ on
Cis pointing towards the
hole in the edge of 7
and 8.

a:

4

b:

2x

Put drop of glue J in the
6 holes of drawersides
7and 8before sliding
them onto the dowels of
drawerback 6.
Slide drawerbase 0 in
the grooves of the
drawer-unit.

c: Turn the drawer wrap

assembly over and push
onto the drawer front 4 .
Use a phillips or flatblade
screwdriver, that is a good
fit, to turn 24mm locking nut
C as far as it will go

- more than 1/2 turn.

2x

c:

2x

5

III

I

Assembly Instructions

AADDL

L1L

D1LLD

D

1

Step 1 continued

finishing the drawers

d: Turn over drawer and

slide Drawerbase supports
Iin corner as shown and
fix them, using the attached
screws .

x: xx

Step 2

Attaching runners

a: Slide top of runners L

foreward and fix on left side
1 as shown using 10mm
fixing screw drawer D.
Insert 2 Large locking nuts
A into left side 1 where
shown.

d:

2x

2x

a:

Finished
front edge

b: Slide top of runners

back.
Fix through 3rd hole of
runner L and pre-drilled
hole of left side 1 using
10mm fixing screw drawer
D.

Repeat a and b on right
sidepanel 2

1

E

R

b:

Finished
front edge

6

Assembly Instructions

B

3

3

BBB

B

J

125

J5EEE

E

Step 3

Insert fittings on top

Screw 24mm locking
screws B into top 3 .

Note: Insert 24mm locking
screw B as far as
shown.

Do not over tighten.

Step 4

Insert fittings on plinth

Put drop of glue J in the 4
holes of plinth 5 .
Then put dowels E into
the holes of plinth 5.

Step 5

a:

Assemble the chest

a: Put drop of glue J

into side-holes 1and2
Slide the sides onto the
plinth 5.

7

Assembly Instructions

A

123

HFF9KKK

K

Step 5 continued

b: Attaching top

Position top 3 onto left
1 and right 2 side .

Use a screwdriver to turn
locking nuts A clockwise
to lock.

c: Fitting back panel

Attach foldy back 9 to
backof the chest using
nails F and hammer.

b:

c:

Unfinished
back edge

Finished
front edge

M

A

Use nailholder H to hold
nails F vertical and at the
correct distance as you
secure the foldy back 9.

Nails F should be spaced
about 150mm apart.

Place the Furniture glides
Kstrategically underneath
the sides 2 and 2 with a
small hammer.

Important:
Chest MUST
be ‘square’
when back is
attached.

8

Assembly Instructions

Step 6

Inserting drawers
a: Pull runners L out.

Slide drawers onto runners
so they butt up against
back of the drawerfront 4.

b: Fix through drawersides

7 and 8 into runners L
using 9mm screws G.

a:

b:

C

c: Finish.

1st small

threaded hole

c:

Assembly is complete.

If you need help or have damaged or missing parts, call the Customer Helpline:

Argos 03456 400 800

9