Hygena BERGEN 2DRW BEDSIDE Instruction manual

Bergen 2 drawer bedside chest

Assembly Instructions- Please keep for future reference 241/6757

DR825140

226/4088

248/5881

Dimensions

Width - 45.5cm

Depth - 38.1cm

Height - 43.9cm

241/6757 OAK
226/4088 WHT
248/5881 WAL

Tip : To prevent damage,

we recommend that you

build your unit on the

carton(s) it was packed in.

Important – Please read these instructions fully before starting assembly

If you need help or have damaged or missing parts, please visit: www.argos-support.co.uk
or email: [e-mail] (quoting your original order number)
Alternatively, call the Spares Helpline on: 0370 112 1928
For any other queries please contact the Customer Helpline on: 0345 640 2020

Issue 2 - 05/08/15

Safety and Care Advice

Important – Please read these instructions fully before starting assembly

• Check you have all the
components and tools listed on
pages 2 and 3.

• Remove all fittings from the
plastic bags and separate them
into their groups.

• Keep children and animals
away from the work area, small
parts could choke if swallowed.

• Make sure you have enough
space to layout the parts before
starting.

• Do not stand or put weight on
the product, this could cause
damage.

• Assemble the item as close
to its final position (in the same

room) as possible.

• Assemble on a soft level
surface to avoid damaging the
unit or your floor.

• Parts of the assembly will be
easier with 2 people.

power drill is set on a low torque
setting.

• Dispose of all packaging
carefully and responsibly.

Glue safety - Take care when using glue, please follow the advice below

Skin contact: Remove

contamination by washing with
soap and water. This procedure
should also be followed prior to
eating and drinking.

Eye contact: Rinse immediately
with clean water for 15 minutes
and seek medical advice.

If swallowed: Seek medical
advice immediately.

•To reduce the
likelihood of
damaging your
product please
ensure that your

Care and maintenance

• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.

Handy Hints

• Assemble all parts and bolts
loosely during assembly, only
once the product is complete
should you fully tighten the bolts

• From time to time check that
there are no loose screws on
this unit.

• Regularly check and ensure
that all bolts and fittings are
tightend properly.

• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.

Note: if required the next
page can be cut out and used
as reference throughout the
assembly. Keep this page with
these instructions for future
reference.

2

For damaged or missing parts, please visit:

Components - Panels

www.argos-support.co.uk or email: [e-mail]

Please check you have all the panels listed below

Left & Right Side x 2

1

(38.7 x 38cm)

P2028

Foot

4

(41x 34cm)

P1987

Left Drawer Side x 2

6

(30.5 x 12cm)

LA163109

Top

2

(45.5 x 38.1cm)

P1985

Drawerfront x 2

5

(41.9 x 18.8cm)

FA4233 / P4233

Drawer Back x 2

7

(37.4 x 12cm)

LA162909

Bottom

3

(45.5 x 38.1cm)

P1986

Right Drawer Side x 2

8

(30.5 x 12cm)

LA163209

Foldy Back

9

(43.5 x 39.8cm)

BO253809

Drawer Base x 2

10

(38.6 x 29.9cm)

BO251209

3

Components - Fittings

105

For damaged or missing parts, please visit:
www.argos-support.co.uk or email: [e-mail]

Please check you have all the fittings listed below

Note: The quantities below are the correct amount to complete the assembly. In some cases more
fittings may be supplied than are required.

1/1

FK1012

A

B

15mm

Large locking nut x 8 (15x12mm) Small locking nut x 4 (12x10mm)

D

10mm Fixing screw drawer x 8

G

Felt selfadhesive x 6

J

PM1516LA

Runner left part A x 2

M

PM1516RA

Runner right part A x 2

Locking screw x 12 (5x24mm)

FK1301

E

12,5mm Pozi screw x 34

FK1416

H

Glue x 1

K

Runner left part B x 2

N

Runner right part B x 2

FK1011

FK1309

FA1510

PM1516LB

PM1516RB

C

12mm

F

30mm Chipboard screw x 4

I

Drawerbase support x 16

L

Drawer handle x 2

FK1010

FK1322

FK1250

GR1978

Tools required

Phillips screwdriver

(medium & large)

Flatblade screwdriver

(medium)

Setsquare

Eye protection
(when using a
hammer or drill)

Ruler - Use this ruler to help correctly identify the screws

0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100

The screws length is measured from the head to the point (30mm screw shown).

4

Small
hammer

0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150

0 1 2 3 4 5 6

Ruler/tape
measure

Scissors

110 115 120 125 130 135 140 145 150 155 160 165 170

Assembly Instructions

C

C

7810J6

C

Step 1

a: Prepare the drawer

fronts

Screw 2 locking screw B
into the holes shown on the
back of each drawer
front 5 .

Note: Insert locking
screw B as far as shown.

Do not over tighten.

b: Prepare the drawer

sides

Insert a small locking nut C
into the hole on left drawer
side 6 and right
drawerside 8.
Make sure the ‘arrow’ on C
is pointing towards the hole
in the edge of 6 and 8.

B

a:

B

5

2x

b:

Put drop of glue J in the 6
holes of drawersides 6 and
8 before sliding them onto
the dowels of
drawerback 7.
Slide drawerbase 0 in the
grooves of the drawer-unit.

c: Turn the drawer wrap

assembly over and push onto
the drawer front 5 . Use a
phillips or flatblade
screwdriver, that is a good fit,
to turn 24mm locking nut C
as far as it will go - more than
1/2 turn.

2x

c:

2x

5

5

III

I

111

1

DDD

D

AAAAAAA

A

Assembly Instructions

Step 1 continued

finishing the drawers

d: Turn over drawer and

slide drawerbase
supports I in corner as
shown and fix them, using
the attached screws .

Step 2

Attaching runners

a: Fix runner left and right

side A J and M on left &
right side 1 as shown using
10mm fixing screw drawer
D and
12,5mm pozi screw E.

d:

2x

a:

J

J

M

b: Insert 8 Large locking

nuts A into left &
right side 1 where shown.
Make sure the ‘arrow’ on
A is pointing towards the
hole in the edge of 1.

E

b:

M

E

E

J

M

E

E

E

6

B3BBB

B

3

3

FFF

F

1

1

AAA

A

Assembly Instructions

Step 3

Attach bottom and foot

Position bottom 3 onto
foot 4 and fix with 30mm
chipboard screw F.

Screw 24mm locking
screws B into bottom 3 .

Note: Insert
locking screw Bas far as
shown.

Do not over tighten.

4

Step 4

Attaching left & right side

Position left & right side 1
onto bottom 3.

Use a screwdriver to turn
locking nuts A clockwise
to lock.

Finished
front edge

M

A

7

911

2

Assembly Instructions

Step 5

Slide in foldy back

Slide foldy back 9
into the grooves in left &
right side 1 .

Step 6

a: Prepare top

Screw 4 locking screw B
into the holes shown on top
2 .

Note: Insert
locking screw Bas far as
shown.

Do not over tighten.

B

B

B

B

8

211

AAAAIIIIIIIIGGG

G

4

9

I

I

Assembly Instructions

Step 6 continued

b: Attaching top

Position top 2 onto left &
right side 1 .

Use a screwdriver to turn
locking nuts A clockwise
to lock.

M

A

Step 7

Fixate foldy back

Turn over chest and slide
drawerbase supportsI in
corner as shown and fix
them, using the attached
screws .

Stick the
selfadhesive feltG
strategically underneath
the foot 4.

Important:
Chest MUST
be ‘square’
when back is
attached.

9

KNEEEEE

E

6

8

Assembly Instructions

E

E5LEE

E

Step 8

Attaching runners

Fix runner left and right side
B K and N on left & right
drawer side 6 and 8 as
shown using 12,5mm pozi
screw E.

Step 9

2x

Attaching drawer handle

Attacht drawer handle L on
drawer front 5 as shown
using 12,5mm pozi screw E.

Step 10

Inserting drawers

2x

10