Hygena BERGEN 180 WHITE Instruction manual

Bergen 180

Assembly Instructions- Please keep for future reference

DR825062

249/4834

248/6921

226/8730

Cabinet

248/7937

247/1651

Doors foil/foil

248/3591

248/8015

Doors foil/mirror

249/6265

Mirror doors

Dimensions

Tip : To prevent damage,

we recommend that you

build your unit on the

carton(s) it was packed in.

Width - 180cm

Depth - 59.5cm

Height - 199.8cm

249/4834 OAK 248/6921 WAL 226/8730 WHT 248/7937 OAK doors 247/1651 WAL doors 248/8015 WAL FOIL MIRROR 248/3591 OAK FOIL MIRROR 249/6265 MIRROR

Important – Please read these instructions fully before starting assembly

If you need help or have damaged or missing parts, please visit: www.argos-support.co.uk or email: Help@ClickSpares.co.uk (quoting your original order number) Alternatively, call the Spares Helpline on: 0370 112 1928 For any other queries please contact the Customer Helpline on: 0345 640 2020

Issue 1 - 03/06/15

Safety and Care Advice

Important – Please read these instructions fully before starting assembly

• Check you have all the components and tools listed on pages 2 and 3.

• Remove all fittings from the plastic bags and separate them into their groups.

• Keep children and animals away from the work area, small parts could choke if swallowed.

• Make sure you have enough space to layout the parts before starting.

Care and maintenance

• Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners.

• Do not stand or put weight on the product, this could cause damage.

• Assemble the item as close to its final position (in the same

room) as possible.

• Assemble on a soft level surface to avoid damaging the unit or your floor.

• Parts of the assembly will be easier with 2 people.

• From time to time check that there are no loose screws on this unit.

•To reduce the likelihood of damaging your product please ensure that your

power drill is set on a low torque setting.

• Dispose of all packaging carefully and responsibly.

• This product should not be discarded with household waste. Take to your local authority waste disposal centre.

Handy Hints

• Assemble all parts and bolts loosely during assembly, only once the product is complete should you fully tighten the bolts

• Regularly check and ensure

tightend properly.

Note: if required the next page can be cut out and used as reference throughout the assembly. Keep this page with these instructions for future reference.

2

Components - Panels

For damaged or missing parts, please visit: www.argos-support.co.uk or email: Help@ClickSpares.co.uk

Please check you have all the panels listed below

Cabinet

Left side

1

(199.8 x 52.9cm)

P2883

Top

5

(177 x 51cm)

P1896

Plinth x2

7

(177 x 6cm)

P7241

Right side

2

(199.8 x 55.8cm)

P2882

Upright

3

(190.3 x 49cm)

P2886

Bottom

6

(177 x 51.1cm)

P1897

8

Shelf x2

(87.7 x 48.8cm)

P1898

Foldy back x2

4

(193 x 89cm)

BO3431

3

Plug, Nylon x 32 (5x9mm)

E

FK1082

Connecting plate x 8

O

FK1236

Brush x 3 (1951mm)

T

PM1652C

Door trim x 1 (1951mm)

U

PM1652D

Door handle x 3 (1951mm)

S

PM1652B

Not used until door assembly

Not used until door asse- mbly

Not used until door assembly

Components - Fittings

For damaged or missing parts, please visit: www.argos-support.co.uk or email: Help@ClickSpares.co.uk

Please check you have all the fittings listed below

Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.

1/2

A

FK1005

Confirmat screw x 4 (5x40mm)

D

FK1309

Screw x 4 (4x12.5mm)

G

FK1052

Double locking screw x 3 (5x66.5mm)

J

FK1248

Corner connector, white x 2

M

FK1235

L-Bracket x 1

P

PM1828

B

Locking screw x 18

(5x24mm)

H

Wood dowel x 4 (8x30mm)

K

Hanger rail support, gray x 4

N

Nail holder x 1

Q

FK1011

C

Screw x 11 (4x15mm)

F

Nail x 60

FK1411

I

Large locking nut x 24 (15x12mm)

FK1217

L

Peg, brown x 1

FK1419

PM1611

R

FK1400

FK1515

FK1012

15mm

FK1234

PK1611

Hanger rail x 2

V

(869mm)

Guide rail x 1, metal (1769mm)

FK1013

W

Guide rail x 1, plastic(1769mm)

ZF99936

OR

Allen key x 1 (3mm)

Wall plug (6mm) and parkerscrew x 1

4

Screw x 33 (4x15mm)

AC

ZF9997L

Front guide part x 2

AI

ZF9997C

Spacer x 1

AE

ZF9997F

Sliding door connecting plate x 2

AK

ZF9997B

Sliding door connecting bracket x 2

AL

ZF9997A

Back guide part x 2

AJ

ZF9998D

Components - Fittings

Not used until door assembly

Please check you have all the fittings listed below

Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.

A

2/2

AA

Screw x 2 (3.5x35mm)

AD

Screw x 2 (4x14mm)

AG

End stop x 2

ZF9997I

ZF9997J

ZF9997G

AB

Screw x 9 (3.5x25mm)

AH

Stop guide rail x 2

ZF9997K

ZF9997H

AF

Tapping block for guide rail x 2

ZF9997E

Tools required

Phillips screwdriver

(medium & large)

Flatblade screwdriver

(medium)

Piercer

(small)

5mm Suitable drill bit

Ruler - Use this ruler to help correctly identify the screws

0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100

Drill

Spirit level

Setsquare

105

Small

Stairs

0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150

0 1 2 3 4 5 6

hammer

Ruler/tape measure

Scissors

Eye protection (when using a hammer or drill)

110 115 120 125 130 135 140 145 150 155 160 165 170

5

Assembly Instructions

BBBBBBBBBBBBBBBBBBB

K

Step 1

a:

Cabinet assembly

a: Screw 9 locking screws

B

into the holes on back

of the left side 1.

AB

D

Mount hanger rail support K, fasten with 1 screw D. Screw D into the board between two predrilled holes. Mount tapping block for guide rail f with two screws b.

b: Screw 9 locking screws

B into the holes on back of the right side 2 .

Mount hanger rail support K, fasten with 1 screw D. Screw D into the board between two predrilled holes.

Mount tapping block for guide rail f with two screws b.

AF

b:

AB

AF

AB

K

Finished front edge

D

K

AF

AB

1

AB

Finished front edge

2

C: Mount hanger rail

support K on the upright 3, fasten with screw D 1x. Screw D into the board between two predrilled holes

Turn over.

Mount hanger rail support K on the upright 3, fasten with screw D 1x. Screw D into the board between two predrilled holes.

6

c:

D

K

3

Finished front edge

Assembly Instructions

568

7

IIIIIIIIIIIIIIIIIIH

H

Step 1

Cabinet assembly

d: Insert 6x small locking

nuts I into the top 5.

Make sure the ‘arrow’ on I is pointing towards the hole in the edge of the top

5.

e: Insert 6x small locking

nuts I into the bottom 6.

Make sure the ‘arrow’ on I is pointing towards the hole in the edge of the bottom 6.

d:

Finished front edge

e:

plain chipboard

Finished front edge

f: Insert 6x small locking

nuts I into the shelf 6.

2x.

Make sure the ‘arrow’ on I is pointing towards the hole in the edge of the bottom 6.

g: Insert 4x wooden

dowels J into the plinth

7. 2x.

f:

g:

2x

Finished front edge

2x

Finished front edge

7

Assembly Instructions

VGG

G

6318855

365

AAA

388

6

Step 1

Cabinet assembly

h: Attach top 5 with 2x

confirmat screws A to the upright 3. Use allenkey V.

Attach bottom 6 with 2x confirmat srews A to the

upright 3

.

i: Attach 2x the shelf 8 to

the upright 3 with 3x double locking screws G.

Use a screwdriver to turn 6x locking nuts clockwise to lock.

Finished front edge

h:

Plain chipboard

i:

j: Attach the left side 1

with 9x double locking screws G on the top 5, shelf 8 and the bottom

6.

Use a screwdriver to turn 9x locking nuts clockwise to lock.

Finished front edge

Plain chipboard

j:

Plain chipboard

8