hygena Bergen 228/2840, 246/9577, 244/0204, 227/6306, Bergen 150 Foil/foil Assembly Instructions Manual

Bergen 150 Foil/mirror

Dimensions

Width - 150cm

Depth - 59.5cm

Height - 199.8cm

Assembly Instructions- Please keep for future reference 228/2840

Tip : To prevent damage,

we recommend that you

build your unit on the

carton(s) it was packed in.

DR8250560

Issue 5 - 09/11/16

Important – Please read these instructions fully before starting assembly

Alternatively, call the Spares Helpline on: 0370 112 1928
For any other queries please contact the Customer Helpline on: 0345 640 2020

If you need help or have damaged or missing parts, please visit: www.argos-support.co.uk
or email: [e-mail] (quoting your original order number)

2

Note: if required the next
page can be cut out and used
as reference throughout the
assembly. Keep this page with
these instructions for future
reference.

• Assemble all parts and bolts
loosely during assembly, only
once the product is complete
should you fully tighten the bolts

• Regularly check and ensure

tightend properly.

Handy Hints

Safety and Care Advice

Important – Please read these instructions fully before starting assembly

• Check you have all the
components and tools listed on
pages 2 and 3.

plastic bags and separate them
into their groups.

• Keep children and animals
away from the work area, small
parts could choke if swallowed.

• Make sure you have enough
space to layout the parts before
starting.

• Do not stand or put weight on
the product, this could cause
damage.

• Assemble the item as close

room) as possible.

• Assemble on a soft level
surface to avoid damaging the

• Parts of the assembly will be
easier with 2 people.

•To reduce the
likelihood of
damaging your
product please
ensure that your

• Dispose of all packaging
carefully and responsibly.

• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.

• From time to time check that
there are no loose screws on
this unit.

• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.

Care and maintenance

power drill is set on a low torque
setting.

• Remove all fittings from the

unit or your floor.

to its final position (in the same

Instruction video

• This manual is provided with an additional instruction
video. If the icon on the right is displayed at a particular
step in the manual, Follow the link: http://nlink.nu/vid02
Or scan the QR code on the left with your phone.

See page 2 for link
to instruction video!

3

Left side

(199.8 x 52.9cm)

1

P2883

Right side

(199.8 x 55.8cm)

2

P2882

Upright

(190.3 x 49cm)

3

P2886

Foldy back x2

(193 x 74cm)

4

BO3430

Bottom

(146.9 x 51.1cm)

6

P1891

Top

(146.9 x 51cm)

5

P1889

Shelf x2

(72.7 x 48.8cm)

8

P1893

Plinth x2

(146.9 x 6cm)

7

Mirror door

(195.2 x 76.5cm)

14

PS3333

Segment middle

(76.5 x 65.1cm)

13

P3268

Segment x2

(76.5 x 65cm)

9

P3299

For damaged or missing parts, please visit:
www.argos-support.co.uk or email: [e-mail]

Components - Panels

Please check you have all the panels listed below

P7242

BO3430.0960

4

Locking screw x 18

(5x24mm)

B

FK1011

Screw x 50 (4x15mm)

C

FK1400

Confirmat screw x 4 (5x40mm)

A

FK1005

Plug, Nylon x 24 (5x9mm)

E

FK1082

Nail x 60

F

FK1515

Screw x 12 (4x12.5mm)

D

FK1309

Wood dowel x 4 (8x30mm)

H

FK1411

Large locking nut x 24 (15x12mm)

I

FK1012

15mm

Double locking screw x 3 (5x66.5mm)

G

FK1052

Hanger rail support, gray x 4

K

FK1217

Peg, brown x 1

L

FK1234

Corner connector, white x 2

J

FK1248

Nail holder x 1

N

FK1419

Connecting plate x 4

O

FK1236

L-Bracket x 1

M

FK1235

Guide rail x 1, metal (1468mm)

Q

PM1612

Guide rail x 1, plastic(1468mm)

R

PK1612

Hanger rail x 2

P

PM1824

(719mm)

Brush x 3 (1952mm)

T

PM1652C

Door trim x 1 (1952mm)

U

PM1652D

Door handle x 3 (1952mm)

S

PM1652B

Wall plug (6mm) and parkerscrew x 1

W

ZF99936

Allen key x 1 (3mm)

V

FK1013

1/2

Please check you have all the fittings listed below

For damaged or missing parts, please visit:
www.argos-support.co.uk or email: [e-mail]

Components - Fittings

Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings
may be supplied than are required.

OR

5

Screw x 33 (4x15mm)

AC

ZF9996L

Screw x 7 (3.5x25mm)

AB

ZF9996K

Screw x 4 (3.5x35mm)

AA

ZF9996I

Tapping block for guide rail x 2

AF

ZF9996E

Screw x 2 (4x14mm)

AD

ZF9996J

Stop guide rail x 2

AH

ZF9996H

Front guide part x 2

AI

ZF9996C

Spacer x 1

AE

ZF9996F

Sliding door connecting plate x 2

AK

ZF9996B

Sliding door connecting bracket x 2

AL

ZF9996A

End stop Right

AM

ZF9996M

End stop Left

AG

ZF9996G

Back guide part x 2

AJ

ZF9996D

A

2/2

Please check you have all the fittings listed below

Components - Fittings

Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings
may be supplied than are required.

Ruler - Use this ruler to help correctly identify the screws

Tools required

0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100

110 115 120 125 130 135 140 145 150 155 160 165 170

105

Phillips screwdriver

(medium & large)

Flatblade screwdriver

Small
hammer

Ruler/tape
measure

Drill

Eye protection
(when using a
hammer or drill)

5mm Suitable drill bit

5mm Suitable drill bit

0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150

0 1 2 3 4 5 6

Stairs

Piercer

Scissors

(medium)

(small)

Spirit level

Setsquare

6

Assembly Instructions

Step 1

Cabinet assembly

a: Screw 9 locking screws

B

into the holes on back

of the left side 1.

Mount hanger rail support
K, fasten with 1 screw D.
Screw D into the board
between two predrilled
holes.
Mount tapping block for
guide rail f with two
screws b.

b: Screw 9 locking screws

B into the holes on back
of the right side 2 .

Mount hanger rail
support K, fasten with 1
screw D. Screw D into
the board between two
predrilled holes.

Mount tapping block for
guide rail f with two
screws b.

C: Mount hanger rail

support K on the
upright 3, fasten with
screw D 1x. Screw D
into the board between two
predrilled holes

Turn over.

Mount hanger rail
support K on the
upright 3, fasten with
screw D 1x. Screw D into
the board between two
predrilled holes.

K

D

1

Finished
front edge

a:

AF

AB

K

D

2

AF

AB

Finished
front edge

b:

BBBBBBBBBBBBBBBBBBB

K

D

3

Finished
front edge

c:

D

K

AF

AB

AB

AB

AB

AF

7

Assembly Instructions

Step 1

Cabinet assembly

d: Insert 6x small locking

nuts I into the top 5.

Make sure the ‘arrow’ on
Iis pointing towards the
hole in the edge of the
top 5.

e: Insert 6x small locking

nuts I into the bottom 6.

Make sure the ‘arrow’ on
I is pointing towards the
hole in the edge of the
bottom 6.

f: Insert 6x small locking

nuts I into the shelf 6.

2x.

Make sure the ‘arrow’ on
I is pointing towards the
hole in the edge of the
bottom 6.

g:Insert 4x wooden

dowelsJ into the plinth 7.

2x.

plain chipboard

Finished
front edge

d:

Finished
front edge

Finished
front edge

e:

f:

Finished
front edge

g:

2x

2x

5

687

IIIIIIIIIIIIIIIIIIH

H

Assembly Instructions

Step x

Xxxxxx

x: x

x: xx

x: xxx

8

Assembly Instructions

Step 1

Cabinet assembly

h: Attach top 5 with 2x

confirmat screws A to the
upright 3. Use allenkey
V.

Attach bottom 6 with 2x
confirmat srews A to the

upright 3

.

i: Attach 2x the shelf 8 to

the upright 3 with 3x
double locking screws G.

Use a screwdriver to turn
6x locking nuts clockwise
to lock.

j: Attach the left side 1

with 9x double locking
screws G on the top 5,
shelf 8 and the bottom

6.

Use a screwdriver to turn
9x locking nuts clockwise
to lock.

VGG

G

6

3

1

885

5

Plain chipboard

Plain chipboard

Plain chipboard

Finished
front edge

h:

Finished
front edge

Finished
front edge

i:

j:

365

AAA

388

6

Assembly Instructions

Step 1

Cabinet assembly

k: Attach 2x the plinth 7

between the left site 1
and the right side 2.
Note: that the finished side
properly placed.

Attach the right side 2
with 9x double locking
screws G on the top 5,
shelf 8 and the bottom 6.

Use a screwdriver to turn
9x locking nuts clockwise
to lock.

Mount corner connector J
with 2 screws C on the
plint 7 and bottom 6 .

l: Attach 2x foldy back 4

to back of cabinet with
the coloured surface facing
the inside of the cabinet
using 60x nails F and
22x screws C.

Use nail holder N to hold
the nails F vertical and at
correct distance as you
secure the 2x foldy back

4. Nails F should be
spaced about 150mm
apart.

Stand up the unit!
2 people required to
stand up the unit.

Important:
Cabinet MUST be
‘square’ when
back is attached.

Finished
front edge

k:

Finished
front edge

JJCCFFF

Finished side

l:

JCC

76776282544N6

2

F

C

N

F

9

Assembly Instructions

Step 1

Cabinet assembly

m: Position L-Bracket M

onto top 5 , by using 1x
screw C.

Position metal guide rail Q
onto top 5 , fix with 6x
screws C.

Attach end stop Right m
on the end of the guide
rail Q with screw d
and screw a.

Attach end stop Left g
on the end of the guide
rail Q with screw d
and screw a.

Place 2x hanger rail P into
hanger rail support K.

n: Position plastic guide

rail R onto bottom 6 , fix
with 7x screws b.

Attach 2x stop guide rail
h on the end of the
guide rail R., mount with
2x screws a.

AD

m:

P

Pn:M

CCC

C

C

C

Q

AHAHABABABABAB

AA

AA

R

AB

AB

C

AM

AAAGAA

AD

10

8

8

123

123

6

5

AD

AG

Q

A

x2

AA

x6

B

Q

x6

C

C

x2

Q

P

K

AB

AA

R

6

7

B

A

D

C

x9

AH

. . . . .

x x

R

x7

No Gap
between metal profiles
and door panel!

Assembly Instructions

Step 2

3 Segment slide door left

a: Put 8x nylon plug E

into the segment 9. Use
a small hammer.
Repeat this step.

c: Mount segment middle

# with 3x screws C
on door trim U.
Mount segment 9
with 4x screws C on door
trim U.

b: Mount door trim U with

3x screws C on segment

9.

Note: there should be no
gap between doorsegment
9 and door trim U.

d: Mount door handle S

on segment 9 with
4x screws C and on
middle segment 0 with 3x
screws C.

Note: there should be no
gap between doorsegment
9 and door trim U.

2x

11

9

E

E

9

9

9

b:

c:

d:

CCCUUCCCCCCCCCCCCCCCCCC

S

9

9

10

10

a:

Assembly Instructions

Step 2

3 Segment slide door left

e: Mount 2x connecting

plate O, each with 2x
screws D on segment
9 and 2x screws D
on middle segment 0.

Remove protective film
from door handle S.
Stick 1x brush T onto
door handle S by partially
remove the cover from
adhease as brush is
applied.

f: Upside.

Mount 2x Sliding door
connecting plate k
squarely by using the
guidemarks in the plate

k, each with 6x screws
c on segment

9.

Attach 1x spacer e with
1x screw c on the
sliding door connecting
plate k.

g: Underside.

Mount 2x back guide
part j , each with 2x
screws c on segment

9.

Please remove

the protective film!

S

T

AC

x2

AJ

AC

AKAKACACACACAC

999

AJ

AJ

AC

ACACAC

e:

f:

g:

12

TOODDDD

S

10

9

AE

See page 2 for link
to instruction video!

13

Assembly Instructions

Step 3

Place left slide door

a: Hook the 2x back guide

part j into the plastice
guide rail R.

a: Detail.

The hook of the back guide
part j should be in the
front guide of the plastic
guide rail R

a:

9910

AJ

AJ

RRR

See page 2 for link
to instruction video!

Assembly Instructions

Step 3

Place left slide door

b: Hook Sliding door

connecting platek
on metal guide rail Q.

b: Detail.

The wheel of the sliding
door connecting plate k
should be in the front guide
of the metal guide rail Q.

To lock the door, lock the
Sliding door connecting
plate k on the guide rail
Q with the locking pawl.

14

push the yellow
lock pin to
secure part k to rail

9109

b:

QQQ

Q

AKAKAK

Assembly Instructions

Step 4

Silde door right

a: Put 8x nylon plug E

into the door #.
Use a small hammer.

b: Mount door handle S

with 10x screws C on door
#.

Note: there should be no
gap between door
# and door handle S.

c: Mount door handle S

with 11x screws C on
door #.

Note: there should be no
gap between door
# and door handle S.

15

E

E

a:

b:

c:

CCCCCCCCCCCCCCCCCCCCCSE

E

131313

S

No Gap
between metal profiles
and door panel!

Assembly Instructions

Step 4

Silde door right

d: Remove protective film

from door handle S.
Stick 2x brush T onto
each door handle S by
partially remove the cover
from adhease as brush
is applied.

e: Upside.

Mount 2x sliding door
connecting bracket l
squarely by using the
guide-marks in the plate

l, each with 6x screws
c on door #.

f: Underside is marked

with a shallow hole !.
Mount 2x front guide
part i , each with 2x
screws c on door

16

Please remove

the protective film!

S

T

x2

AC

AI

ACACACACACACAC

AC

d:

e:

f:

T

T

AL

AL

S

S

131313

AI

AI

77mm

31mm

!

31mm

77mm

See page 2 for link
to instruction video!

13

Assembly Instructions

Step 5

Place right slide door

a: Hook the 2x front guide

part i into the plastice
guide rail R.

a: Detail.

The hook of the front guide
part i should be in the
rear guide of the plastic
guide rail R

a:

17

R

R

AIRAI

See page 2 for link
to instruction video!

Assembly Instructions

Step 5

Place right slide door

b: Hook the sliding door

connecting bracketl
on metal guide rail Q.

b: Detail.

The wheel of the sliding
door connecting bracket
l should be in the rear
guide of the metal guide
rail Q.

To lock the door, lock the
sliding door connecting
bracket l on the
guide rail Q with the
locking pawl.

18

13

a:

QQQ

Q

ALALAL

Assembly Instructions

Step 6

Place cabinet

m: Use to 1x wall plug W

to mount L-Bracket M on
the wall,
please see last page for
more information.

b: Before adjusting the

doors, use a spirit level to
check if the base of this
unit is level front-to-back
and side-to-side in the
three positions shown.

Use pegs L to square
your unit. Knock peg L in,
as far as you require,
under the ends of the unit
and then snap off flush
with the panel.

a:

b:

19

MMW

SNAP!

L

L

A Guide to - Wall Mounting & Fixings

Important note:

Types of walls

Care &
Maintenance

No.1 “General Purpose” wall plug

No.6 “Shield Anchor” wall plug

Heavy loads

No.3 “Cavity Fixing” wall plug

No.4 “Cavity Fixing-Heavy Duty”

wall plug

No.5 “Hammer Fixing” wall plug

No.2 “Plasterboard” wall plug

Generally aerated blocks should not
be used to support heavy loads, use
a specialist fitting in this case. For light
loads, general purpose wall plugs can
be used.

For use with heavier loads such as TV
& HiFi speakers and satelite dishes etc.

For use with plasterboard partitions or
hollow wooden doors.

For use when fitting or supporting
heavy loads such as shelving, wall
cabinets and coat racks.

For use with walls stuck with
plasterboard. The hamemr fixing allows
it to be fixed to the wall rather than the
plasterboard. Always check the fixing
is secure to the retaining wall.is secure to the retaining wall.

For use when attaching light loads on
to plasterboard partitions.

Safety: Always check the fitting
and location to ensure your safety
in and around the home.

Fitting: From time to time check
the fitting to ensure the wall plugs
or screws do not become loose.

You can use one of the following types of wall plug if your walls are made
of brick, breeze block, concrete, stone or wood.

Important: When drilling into walls always

check that there are no hidden wires or pipes etc.

Hints:

1: General rule: Always use a larger screw and wall plug

if you are not sure.

2: Ensure you use the recommended drill bit to match the wall

plug and hole size.

3: Ensure you drill the hole horizontally, do not force the drill or

enlarge the hole.

4: Take extra care when drilling high walls, ceilings and ceramic

tiles. Ensure wall plugs are inserted beyond the thickness of
the ceramic tiles to avoid the tiles splitting or cracking.

5: Ensure wall plugs are well fitted and are a tight fit in the

drilled hole.

If plastic wall plugs
are supplied with your
product:

Make sure that the screws and wall plugs being used
are suitable for supporting your unit. Consult a qualified
tradesperson if you are unsure.

- these are only suitable for
use in masonry walls.

If you are in any doubt about
the correct wall plugs for
your wall, seek professional
advice.

Failure of the product due to
using incorrect fixings is the
responsibility of the installer.