Page 1
Bergen 120 Foil/ foil
Assembly Instructions- Please keep for future reference
DR825005
258/1417
257/1740
258/5963
Dimensions
Width - 120cm
Depth - 59.5cm
Height - 199.8cm
Tip : To prevent damage,
we recommend that you
build your unit on the
carton(s) it was packed in.
258/1417 OAK
258/5963 WAL
257/1740 WHT
Important – Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, please visit: www.argos-support.co.uk
or email: Help@ClickSpares.co.uk (quoting your original order number)
Alternatively, call the Spares Helpline on: 0370 112 1928
For any other queries please contact the Customer Helpline on: 0345 640 2020
Issue 1 - 03/07/14
Page 2
Safety and Care Advice
Important – Please read these instructions fully before starting assembly
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close
to its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor.
• Parts of the assembly will be
easier with 2 people.
• From time to time check that
there are no loose screws on
this unit.
•To reduce the
likelihood of
damaging your
product please
ensure that your
power drill is set on a low torque
setting.
• Dispose of all packaging
carefully and responsibly.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Handy Hints
• Assemble all parts and bolts
loosely during assembly, only
once the product is complete
should you fully tighten the bolts
• Regularly check and ensure
tightend properly.
Note: if required the next
page can be cut out and used
as reference throughout the
assembly. Keep this page with
these instructions for future
reference.
2
Page 3
Components - Panels
For damaged or missing parts, please visit:
www.argos-support.co.uk or email: Help@ClickSpares.co.uk
Please check you have all the panels listed below
Left side
1
(199.8 x 52.9cm)
P2883
Top
5
(117 x 51cm)
P1883
Plinth x2
7
(117 x 6cm)
P7883
Right side
2
(199.8 x 55.8cm)
P2882
Upright
3
(190.3 x 49cm)
P2886
Bottom
6
(117 x 51.1cm)
P1884
8
Shelf x2
(57.7 x 48.8cm)
P1886
Foldy back x2
4
(193 x 59cm)
BO3429
Segment x4
9
(61.3 x 65cm)
P3189
Segment middle x2
10
(61.3 x 65.1cm)
P3259
3
Page 4
Components - Fittings
For damaged or missing parts, please visit:
www.argos-support.co.uk or email: Help@ClickSpares.co.uk
Please check you have all the fittings listed below
Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings
may be supplied than are required.
1/2
A
FK1005
Confirmat screw x 4 (5x40mm)
D
FK1309
Screw x 20 (4x12.5mm)
G
FK1052
Double locking screw x 3 (5x66.5mm)
J
FK1248
Corner connector, white x 2
M
FK1235
L-Bracket x 1
P
PM1823
B
Locking screw x 18 (5x24mm)
E
Plug, Nylon x 32 (5x9mm)
H
Wood dowel x 4 (8x30mm)
K
Hanger rail support, gray x 4
N
Nail holder x 1
Q
FK1011
C
Screw x 49 (4x15mm)
FK1082
F
Nail x 60
FK1411
I
Large locking nut x 24 (15x12mm)
FK1217
L
Peg, brown x 1
FK1419
O
Connecting plate x 4
PM1613
R
FK1400
FK1515
FK1012
15mm
FK1234
FK1236
PK1613
Hanger rail x 2
(569mm)
S
Door handle x 3 (1952mm)
V
OR
Allen key x 1 (3mm)
PM1652B
FK1013
Guide rail x 1, metal (1169mm)
T
Brush x 3 (1952mm)
W
PM1652C
ZF99936
Wall plug (6mm) and parkerscrew x 1
Guide rail x 1, plastic(1169mm)
U
Door trim x 1 (1952mm)
PM1652D
4
Page 5
Components - Fittings
Please check you have all the fittings listed below
Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings
may be supplied than are required.
A
2/2
AA
Screw x 2 (3.5x35mm)
AD
Screw x 2 (4x14mm)
AG
End stop x 2
AJ
Back guide part x 2
ZF9997I
ZF9997J
ZF9997G
ZF9998D
AB
Screw x 6 (3.5x25mm)
AE
Spacer x 1
AH
Stop guide rail x 2
AK
Sliding door connecting plate x 2
ZF9997K
ZF9997F
ZF9997H
ZF9997B
AC
Screw x 33
AF
(4x15mm)
ZF9997L
ZF9997E
Tapping block for guide rail x 2
AI
ZF9997C
Front guide part x 2
AL
ZF9997A
Sliding door connecting bracket x 2
Tools required
Phillips screwdriver
(medium & large)
Stairs
Drill
Flatblade screwdriver
(medium)
Piercer
(small)
Spirit level
5mm Suitable drill bit
5mm Suitable drill bit
Setsquare
Ruler - Use this ruler to help correctly identify the screws
105
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100
110 115 120 125 130 135 140 145 150 155 160 165 170
0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150
0 1 2 3 4 5 6
Eye protection
(when using a
hammer or drill)
Small
hammer
Ruler/tape
measure
Scissors
5
Page 6
Assembly Instructions
BBBBBBBBBBBBBBBBBBB
K
Step 1
a:
Cabinet assembly
a: Screw 9 locking screws
B
into the holes on back
of the left side 1.
AB
D
D
Mount hanger rail support
K, fasten with 1 screw D.
Screw D into the board
between two predrilled
holes.
Mount tapping block for
guide rail f with two
screws b.
b: Screw 9 locking screws
B into the holes on back
of the right side 2 .
Mount hanger rail
support K, fasten with 1
screw D. Screw D into
the board between two
predrilled holes.
Mount tapping block for
guide rail f with two
screws b.
AF
b:
AB
AB
AF
AF
AB
K
Finished
front edge
D
K
AF
AB
1
AB
Finished
front edge
2
C: Mount hanger rail
support K on the
upright 3, fasten with
screw D 1x. Screw D
into the board between two
predrilled holes
Turn over.
Mount hanger rail
support K on the
upright 3, fasten with
screw D 1x. Screw D
into the board between two
predrilled holes.
6
c:
D
K
3
Finished
front edge
Page 7
Assembly Instructions
568
7
IIIIIIIIIIIIIIIIIIH
H
Step 1
Cabinet assembly
d: Insert 6x small locking
nuts I into the top 5.
Make sure the ‘arrow’ on
I is pointing towards the
hole in the edge of the
top 5.
e: Insert 6x small locking
nuts I into the bottom 6.
Make sure the ‘arrow’ on
I is pointing towards the
hole in the edge of the
bottom 6.
d:
Finished
front edge
e:
plain chipboard
Finished
front edge
f: Insert 6x small locking
nuts I into the shelf 6.
2x.
Make sure the ‘arrow’ on
I is pointing towards the
hole in the edge of the
bottom 6.
g: Insert 4x wooden
dowelsJ into the
plinth 7. 2x.
f:
g:
2x
Finished
front edge
2x
Finished
front edge
77
Page 8
Assembly Instructions
VGG
G
6318855
365
AAA
388
6
Assembly Instructions
Step x
Step 1
Xxxxxx
Cabinet assembly
x: x
h: Attach top 5 with 2x
confirmat screws A to the
upright 3. Use allenkeyV.
Attach bottom 6 with 2x
confirmat srews A to the
upright 3
x: xx
i: Attach 2x the shelf 8 to
the upright 3 with 3x
double locking screws G.
Use a screwdriver to turn
6x locking nuts clockwise
to lock.
.
Finished
front edge
h:
Plain chipboard
i:
j: Attach the left side 1
with 9x double locking
screws G on the top 5,
shelf 8 and the
x: xxx
bottom 6.
Use a screwdriver to turn
9x locking nuts clockwise
to lock.
Finished
front edge
Finished
front edge
Plain chipboard
j:
Plain chipboard
8
8
Page 9
Assembly Instructions
JJCCFFF
JCC
76776282544N6
2
F
C
N
F
Step 1
Cabinet assembly
k: Attach 2x the plinth 7
between the left site 1
and the right side 2.
Note: that the finished side
properly placed.
Attach the right side 2
with 9x double locking
screws G on the top 5,
shelf 8 and
the bottom 6.
k:
Use a screwdriver to turn 9x
locking nuts clockwise to
lock.
Mount corner connector J
with 2 screws C on the
plinth 7 and bottom 6.
l: Attach 2x foldy back 4
to back of cabinet with
the coloured surface facing
the inside of the cabinet
using 60x nails F and
22x screws C.
Use nail holder N to hold
the nails F vertical and at
correct distance as you
secure the
2x foldy back 4.
Nails F should be spaced
about 150mm apart.
Finished
front edge
Finished side
l:
Important:
Cabinet MUST
be ‘square’ when
Finished
front edge
back is attached.
Stand up the unit!
2 people required to
stand up the unit.
9
9
Page 10
Assembly Instructions
AD
P
P
AG
AG
M
CCCCCCQ
AHAHABABABABABAAAA
R
88123
123
6
5
ADQAD
AG
Q
P
K
AB
AA
R
6
7
AH
R
Step 1
Cabinet assembly
m: Position L-Bracket M
onto top 5 , by using 1x
screw C.
Position metal guide rail Q
onto top 5 , fix with 5x
screws C.
Attach 2x end stop g on
the end of the guide rail Q
with 2x screws d.
Place 2x hanger rail P into
hanger rail support K.
A
x2
B
x5
C
x5
C
m:
n: Position plastic guide
rail R onto bottom 6 , fix
with 5x screws b.
Attach 2x stop guide rail
h on the end of the
guide rail R., mount with
2x screws a.
A
C
x x
. . . . .
n:
B
x7
D
10
10
x 5
Page 11
Assembly Instructions
E
E
CCCUUCCCCCCCCCCCCCCCCCC
S
99999
9
Step 2
3 Segment slide door left
a: Put 8x nylon plug E
into the segment 9. Use
a small hammer.
Repeat this step.
b: Mount door trim U with
3x screws C on segment
9.
Note: there should be no
gap between doorsegment
9 and door trim U.
a:
2x
b:
c: Mount segment middle
2 with 3x screws C
on door trim U.
Mount segment 9
with 4x screws C on door
trim U.
d: Mount door handle S
on segment 9 with
4x screws C and on
middle segment 0 with 3x
screws C.
No Gap
between metal profiles
and door panel!
c:
10
d:
Note: there should be no
gap between doorsegment
0 and door handle S.
10
11
Page 12
Assembly Instructions
S
T
AKAKACACACACACAJAJACACACAC
TOODDDD
S
AE
AC
AJ
AC
999
9
Step 2
3 Segment slide door left
e: Mount 2x connecting
plate O, each with 2x
screws D on segment
9 and 2x screws D
on middle segment 0.
e:
Remove protective film
from door handle S.
Stick 1x brush T onto
door handle S by partially
removing the cover from
adhease as brush is
applied.
f: Upside.
Mount 2x Sliding door
connecting plate k
squarely by using the guidemarks in the plate, each
with 6x screws c on
segment 9.
Attach 1x spacer e with
1x screw c on the brush
side sliding door connecting
plate k.
10
Please remove
the protective film!
f:
g: Underside.
Mount 2x back guide
part j , each with 2x
screws c on segment
9.
g:
x2
12
Page 13
Assembly Instructions
AJ
AJ
RRR
9
9
Step 3
Place left slide door
2 People are required for
step 3a and 3b.
Hook the 2x back guide
a:
part j into the plastic
guide rail R.
a:
10
a: Detail.
The hook of the back guide
part j should be in the
front guide of the plastic
guide rail R
13
Page 14
Assembly Instructions
QQQ
Q
AKAKAK
9
9
Step 3
Place left slide door
b: Hook Sliding door
connecting platek
on metal guide rail Q.
b:
10
b: Detail.
The wheel of the sliding
door connecting plate k
should be in the front guide
of the metal guide rail Q.
To lock the door, lock the
Sliding door connecting
plate k on the guide
railQ with the locking pawl.
push the yellow
lock pin to
secure part
k to rail
14
Page 15
Assembly Instructions
E
E
CCCUUCCCCCCCCCCCCCCCCCC
S
99999
9
Step 4
3 Segment slide door left
a: Put 8x nylon plug E
into the segment 1. Use
a small hammer.
Repeat this step.
b: Mount door trim U with
3x screws C on segment
1.
Note: there should be no
gap between doorsegment
1 and door trim U.
a:
2x
b:
c: Mount segment middle
2 with 3x screws C
on door trim U.
Mount segment 1
with 4x screws C on door
trim U.
d: Mount door handle S
on segment 1 with
4x screws C and on
middle segment 2 with 3x
screws C.
No Gap
between metal profiles
and door panel!
c:
10
d:
Note: there should be no
gap between doorsegment
1 and door handle S.
10
15
Page 16
Assembly Instructions
S
T
ACAIACACAC
AC
999
ACACAC
AC
TOODDDD
T
AL
AL
S
S
10
9
AI
AI
Step 4
3 Segment slide door
right
e: Mount 2x connecting
plate O, each with 2x
screws D on segment 9
and 2x screws D on
middle segment 0 .
Remove protective film
from door handle S.
Stick 2x brush T onto 2x
door handle S by partially
remove the cover from
adhease as brush is
applied.
Please remove
the protective film!
e:
f: Upside.
Mount 2x sliding door
connecting bracket l
squarely by using the
guidemarks in the plate,
each with 6x screws c
on segment 9.
g: Underside.
Mount 2x front guide
part i , each with 2x
screws c on segment 9.
f:
g:
x2
16
Page 17
Assembly Instructions
R
RAIR
9
9
Step 5
Place right slide door
a: Hook the 2x front guide
part i into the plastic
guide rail R.
a:
10
a: Detail.
The hook of the front guide
part i should be in the
rear guide of the plastic
guide rail R
17
Page 18
Assembly Instructions
QQQ
Q
ALALAL
9
9
Step 5
Place right slide door
b: Hook the sliding door
connecting bracketl
on metal guide rail Q.
a:
10
b: Detail.
The wheel of the sliding
door connecting bracket
l should be in the rear
guideof the metal guide
rail Q.
To lock the door, lock the
sliding door connecting
bracket l on the
guide rail Q with the
locking pawl.
18
Page 19
MMW
L
L
Assembly Instructions
Step 6
Place cabinet
a: Use to 1x wall plug W
to mount L-Bracket M on
the wall,
please see last page for
more information.
a:
b: Before adjusting the
doors, use a spirit level to
check if the base of this
unit is level front-to-back
and side-to-side in the
three positions shown.
Use pegs L to square
your unit. Knock peg L in,
as far as you require,
under the ends of the unit
and thensnap off flush with
the panel.
b:
SNAP!
19
Page 20
A Guide to - Wall Mounting & Fixings
Important note:
If plastic wall plugs
are supplied with your
product:
- these are only suitable for
use in masonry walls.
If you are in any doubt about
the correct wall plugs for
your wall, seek professional
advice.
Failure of the product due to
using incorrect fixings is the
responsibility of the installer.
Important: When drilling into walls always
check that there are no hidden wires or pipes etc.
Make sure that the screws and wall plugs being used
are suitable for supporting your unit. Consult a qualified
tradesperson if you are unsure.
Hints:
1: General rule: Always use a larger screw and wall plug
if you are not sure.
2: Ensure you use the recommended drill bit to match the wall
plug and hole size.
3: Ensure you drill the hole horizontally, do not force the drill or
enlarge the hole.
4: Take extra care when drilling high walls, ceilings and ceramic
tiles. Ensure wall plugs are inserted beyond the thickness of
the ceramic tiles to avoid the tiles splitting or cracking.
5: Ensure wall plugs are well fitted and are a tight fit in the
drilled hole.
Types of walls
No.1 “General Purpose” wall plug
Generally aerated blocks should not
be used to support heavy loads, use
a specialist fitting in this case. For light
loads, general purpose wall plugs can
be used.
No.2 “Plasterboard” wall plug
You can use one of the following types of wall plug if your walls are made
of brick, breeze block, concrete, stone or wood.
No.3 “Cavity Fixing” wall plug
For use with plasterboard partitions or
hollow wooden doors.
No.4 “Cavity Fixing-Heavy Duty”
wall plug
No.5 “Hammer Fixing” wall plug
For use with walls stuck with
plasterboard. The hamemr fixing allows
it to be fixed to the wall rather than the
plasterboard. Always check the fixing
is secure to the retaining wall.is secure to the retaining wall.
No.6 “Shield Anchor” wall plug
Heavy loads
For use when attaching light loads on
to plasterboard partitions.
Care &
Maintenance
For use when fitting or supporting
heavy loads such as shelving, wall
cabinets and coat racks.
Safety: Always check the fitting
and location to ensure your safety
in and around the home.
For use with heavier loads such as TV
& HiFi speakers and satelite dishes etc.
Fitting: From time to time check
the fitting to ensure the wall plugs
or screws do not become loose.
Page 21
Bergen 2 drawer bedside chest
Assembly Instructions- Please keep for future reference 241/6757
DR82514
226/4088
248/5881
Dimensions
Width - 45.5cm
Depth - 38.1cm
Height - 43.9cm
241/6757 OAK
226/4088 WHT
248/5881 WAL
Tip : To prevent damage,
we recommend that you
build your unit on the
carton(s) it was packed in.
Important – Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, please visit: www.argos-support.co.uk
or email: Help@ClickSpares.co.uk (quoting your original order number)
Alternatively, call the Spares Helpline on: 0370 112 1928
For any other queries please contact the Customer Helpline on: 0345 640 2020
Issue 1 - 17/07/14
Page 22
Safety and Care Advice
Important – Please read these instructions fully before starting assembly
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close
to its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor.
• Parts of the assembly will be
easier with 2 people.
power drill is set on a low torque
setting.
• Dispose of all packaging
carefully and responsibly.
Glue safety - Take care when using glue, please follow the advice below
Skin contact: Remove
contamination by washing with
soap and water. This procedure
should also be followed prior to
eating and drinking.
Eye contact: Rinse immediately
with clean water for 15 minutes
and seek medical advice.
If swallowed: Seek medical
advice immediately.
•To reduce the
likelihood of
damaging your
product please
ensure that your
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
Handy Hints
• Assemble all parts and bolts
loosely during assembly, only
once the product is complete
should you fully tighten the bolts
• From time to time check that
there are no loose screws on
this unit.
• Regularly check and ensure
that all bolts and fittings are
tightend properly.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Note: if required the next
page can be cut out and used
as reference throughout the
assembly. Keep this page with
these instructions for future
reference.
2
Page 23
For damaged or missing parts, please visit:
Components - Panels
www.argos-support.co.uk or email: Help@ClickSpares.co.uk
Please check you have all the panels listed below
Left & Right Side x 2
1
(38.7 x 38cm)
P2028
Foot
4
(41x 34cm)
P1987
Left Drawer Side x 2
6
(30.5 x 12cm)
LA163109
Top
2
(45.5 x 38.1cm)
P1985
Drawerfront x 2
5
(41.9 x 18.8cm)
FA4233 / P4233
Drawer Back x 2
7
(37.4 x 12cm)
LA162909
Bottom
3
(45.5 x 38.1cm)
P1986
Right Drawer Side x 2
8
(30.5 x 12cm)
LA163209
Foldy Back
9
(43.5 x 39.8cm)
BO253809
Drawer Base x 2
10
(38.6 x 29.9cm)
BO251209
3
Page 24
Components - Fittings
105
For damaged or missing parts, please visit:
www.argos-support.co.uk or email: Help@ClickSpares.co.uk
Please check you have all the fittings listed below
Note: The quantities below are the correct amount to complete the assembly. In some cases more
fittings may be supplied than are required.
1/1
FK1012
A
B
15mm
Large locking nut x 8 (15x12mm) Small locking nut x 4 (12x10mm)
D
10mm Fixing screw drawer x 8
G
Felt selfadhesive x 6
J
PM1516LA
Runner left part A x 2
M
PM1516RA
Runner right part A x 2
Locking screw x 12 (5x24mm)
FK1301
E
12,5mm Pozi screw x 34
FK1416
H
Glue x 1
K
Runner left part B x 2
N
Runner right part B x 2
FK1011
FK1309
FA1510
PM1516LB
PM1516RB
C
12mm
F
30mm Chipboard screw x 4
I
Drawerbase support x 16
L
Drawer handle x 2
FK1010
FK1322
FK1250
GR1978
Tools required
Phillips screwdriver
(medium & large)
Flatblade screwdriver
(medium)
Setsquare
Eye protection
(when using a
hammer or drill)
Ruler - Use this ruler to help correctly identify the screws
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100
The screws length is measured from the head to the point (30mm screw shown).
4
Small
hammer
0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150
0 1 2 3 4 5 6
Ruler/tape
measure
Scissors
110 115 120 125 130 135 140 145 150 155 160 165 170
Page 25
Assembly Instructions
C
C
7810J6
C
Step 1
a: Prepare the drawer
fronts
Screw 2 locking screw B
into the holes shown on the
back of each drawer
front 5 .
Note: Insert locking
screw B as far as shown.
Do not over tighten.
b: Prepare the drawer
sides
Insert a small locking nut C
into the hole on left drawer
side 6 and right
drawerside 8.
Make sure the ‘arrow’ on C
is pointing towards the hole
in the edge of 6 and 8.
B
a:
B
5
2x
b:
Put drop of glue J in the 6
holes of drawersides 6 and
8 before sliding them onto
the dowels of
drawerback 7.
Slide drawerbase 0 in the
grooves of the drawer-unit.
c: Turn the drawer wrap
assembly over and push onto
the drawer front 5 . Use a
phillips or flatblade
screwdriver, that is a good fit,
to turn 24mm locking nut C
as far as it will go - more than
1/2 turn.
2x
c:
2x
5
5
Page 26
III
I
111
1
DDD
D
AAAAAAA
A
Assembly Instructions
Step 1 continued
finishing the drawers
d: Turn over drawer and
slide drawerbase
supports I in corner as
shown and fix them, using
the attached screws .
Step 2
Attaching runners
a: Fix runner left and right
side A J and M on left &
right side 1 as shown using
10mm fixing screw drawer
D and
12,5mm pozi screw E.
d:
2x
a:
J
J
M
b: Insert 8 Large locking
nuts A into left &
right side 1 where shown.
Make sure the ‘arrow’ on
A is pointing towards the
hole in the edge of 1.
E
b:
M
E
E
J
M
E
E
E
6
Page 27
B3BBB
B
3
3
FFF
F
1
1
AAA
A
Assembly Instructions
Step 3
Attach bottom and foot
Position bottom 3 onto
foot 4 and fix with 30mm
chipboard screw F.
Screw 24mm locking
screws B into bottom 3 .
Note: Insert
locking screw Bas far as
shown.
Do not over tighten.
4
Step 4
Attaching left & right side
Position left & right side 1
onto bottom 3.
Use a screwdriver to turn
locking nuts A clockwise
to lock.
Finished
front edge
M
A
7
Page 28
911
2
Assembly Instructions
Step 5
Slide in foldy back
Slide foldy back 9
into the grooves in left &
right side 1 .
Step 6
a: Prepare top
Screw 4 locking screw B
into the holes shown on top
2 .
Note: Insert
locking screw Bas far as
shown.
Do not over tighten.
B
B
B
B
8
Page 29
211
AAAAIIIIIIIIGGG
G
4
9
I
I
Assembly Instructions
Step 6 continued
b: Attaching top
Position top 2 onto left &
right side 1 .
Use a screwdriver to turn
locking nuts A clockwise
to lock.
M
A
Step 7
Fixate foldy back
Turn over chest and slide
drawerbase supportsI in
corner as shown and fix
them, using the attached
screws .
Stick the
selfadhesive feltG
strategically underneath
the foot 4.
Important:
Chest MUST
be ‘square’
when back is
attached.
9
Page 30
KNEEEEE
E
6
8
Assembly Instructions
E
E5LEE
E
Step 8
Attaching runners
Fix runner left and right side
B K and N on left & right
drawer side 6 and 8 as
shown using 12,5mm pozi
screw E.
Step 9
2x
Attaching drawer handle
Attacht drawer handle L on
drawer front 5 as shown
using 12,5mm pozi screw E.
Step 10
Inserting drawers
2x
10
Page 31
Bergen 3 drawer bedside chest
Assembly Instructions- Please keep for future reference 244/7276
DR82515
228/4532
246/5760
Dimensions
Tip : To prevent damage,
Width - 76.2cm
Depth - 38.1cm
Height - 63.1cm
244/7276 OAK
228/4532 WHT
246/5760 WAL
we recommend that you
build your unit on the
carton(s) it was packed in.
Important – Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, please visit: www.argos-support.co.uk
or email: Help@ClickSpares.co.uk (quoting your original order number)
Alternatively, call the Spares Helpline on: 0370 112 1928
For any other queries please contact the Customer Helpline on: 0345 640 2020
Issue 1 - 17/07/14
Page 32
Safety and Care Advice
Important – Please read these instructions fully before starting assembly
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close
to its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor.
• Parts of the assembly will be
easier with 2 people.
power drill is set on a low torque
setting.
• Dispose of all packaging
carefully and responsibly.
Glue safety - Take care when using glue, please follow the advice below
Skin contact: Remove
contamination by washing with
soap and water. This procedure
should also be followed prior to
eating and drinking.
Eye contact: Rinse immediately
with clean water for 15 minutes
and seek medical advice.
If swallowed: Seek medical
advice immediately.
•To reduce the
likelihood of
damaging your
product please
ensure that your
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
Handy Hints
• Assemble all parts and bolts
loosely during assembly, only
once the product is complete
should you fully tighten the bolts
• From time to time check that
there are no loose screws on
this unit.
• Regularly check and ensure
that all bolts and fittings are
tightend properly.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Note: if required the next
page can be cut out and used
as reference throughout the
assembly. Keep this page with
these instructions for future
reference.
2
Page 33
For damaged or missing parts, please visit:
Components - Panels
www.argos-support.co.uk or email: Help@ClickSpares.co.uk
Please check you have all the panels listed below
Left & Right Side x 2
1
(57.9 x 38cm)
P2029
Foot
4
(71.7x 34cm)
P1990
Left Drawer Side x 3
6
(30.5 x 12cm)
LA163109
Top
2
(76.2 x 38.1cm)
P1988
Drawerfront x 3
5
(72.6 x 18.8cm)
FA4234 / P4234
Drawer Back x 3
7
(68.2 x 12cm)
LA162609
Bottom
3
(76.2 x 38.1cm)
P1989
Right Drawer Side x 3
8
(30.5 x 12cm)
LA163209
Foldy Back
9
(59 x 74.2cm)
BO253909
Drawer Base x 3
10
(69.1 x 29.9cm)
BO253709
3
Page 34
105
Components - Fittings
For damaged or missing parts, please visit:
www.argos-support.co.uk or email: Help@ClickSpares.co.uk
Please check you have all the fittings listed below
Note: The quantiti es below are the correct amount to complete the assembly. In some cases more
1/1
FK1012
A
B
15mm
Large locking nut x 8 (15x12mm) Small locking nut x 6 (12x10mm)
D
10mm Fixing screw drawer x 12
G
Felt selfadhesive x 6
J
PM1516LA
Runner left part A x 3
M
PM1516RA
Runner right part A x 3
Locking screw x 14 (5x24mm)
FK1301
E
12,5mm Pozi screw x 51
FK1416
H
Glue x 1
K
Runner left part B x 3
N
Runner right part B x 3
FK1011
FK1309
FA1510
PM1516LB
PM1516RB
C
12mm
F
30mm Chipboard screw x 4
I
Drawerbase support x 28
L
Drawer handle x 3
FK1010
FK1322
FK1250
GR1978
Tools required
Phillips screwdriver
(medium & large)
Flatblade screwdriver
(medium)
Setsquare
Eye protection
(when using a
hammer or drill)
Ruler - Use this ruler to help correctly identify the screws
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100
4
4
The screws length is measured from the head to the point (30mm screw shown).
Small
hammer
0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150
0 1 2 3 4 5 6
Ruler/tape
measure
Scissors
110 115 120 125 130 135 140 145 150 155 160 165 170
Page 35
Assembly Instructions
C
C
7810J6
C
Step 1
a: Prepare the drawer
fronts
Screw 2 locking screw B
into the holes shown on the
back of each
drawer front 5 .
Note: Insert
locking screw B
as far as shown.
Do not over tighten.
a:
B
3x
5
B
b: Prepare the drawer
sides
Insert a small locking nut C
into the hole on left drawer
side 6 and right
drawerside 8.
Make sure the ‘arrow’ on C
is pointing towards the hole
in the edge of 6 and 8.
Put drop of glue J in the 6
holes of drawersides 6and
8before sliding them onto
the dowels of
drawerback 7.
Slide drawerbase 0 in the
grooves of the drawer-unit.
c: Turn the drawer wrap
assembly over and push onto
the drawer front 5 . Use a
phillips or flatblade
screwdriver, that is a good fit,
to turn 24mm locking nut C
as far as it will go - more than
1/2 turn.
b:
3x
c:
5
3x
5
Page 36
IIIII
I
111
1
DDD
D
AAAAAAA
A
Assembly Instructions
Step 1 continued
finishing the drawers
d: Turn over drawer and
slide drawerbase
supportsI in corner as
shown and fix them, using
the attached screws .
Step 2
Attaching runners
a: Fix runner left and right
side A J and M on left &
right side 1 as shown
using 10mm fixing
screw drawer D and
12,5mm pozi screw E.
d:
3x
a:
J
J
J
M
b: Insert 8 Large locking
nuts A into left & right
side 1 where shown.
Make sure the ‘arrow’
on Ais pointing towards
the hole in the edge of 1.
E
b:
M
M
E
E
J
M
E
E
E
6
Page 37
Assembly Instructions
B3BBB
B
3
3
FFF
F
1
1
AAA
A
Step 3
Attach bottom and foot
Position bottom 3 onto
foot 4 and fix with 30mm
chipboard screw F.
Screw 24mm locking
screws B into bottom 3 .
Note: Insert locking
screw B as far as shown.
Do not over tighten.
4
Finished
front edge
Step 4
Attaching left & right side
Position left & right side 1
onto bottom 3.
Use a screwdriver to turn
locking nuts A clockwise
to lock.
M
A
7
Page 38
911
2
Assembly Instructions
Step 5
Slide in foldy back
Slide foldy back 9
into the grooves in left &
right side 1 .
Step 6
a: Prepare top
Screw 4 locking screw B
into the holes shown on top
2 .
Note: Insert locking screw
Bas far as shown.
Do not over tighten.
B
B
B
B
8
Page 39
211
AAAAIIIIIIIIIIGGGGG
G
4
9
Assembly Instructions
Step 6 continued
b: Attaching top
Position top 2 onto left &
right side 1 .
Use a screwdriver to turn
locking nuts A clockwise
to lock.
M
A
Step 7
Fixate foldy back
Turn over chest and slide
drawerbase supportsI in
corner as shown and fix
them, using the attached
screws .
Stick the selfadhesive feltG
strategically underneath
the foot 4.
Important:
Chest MUST
be ‘square’
when back is
attached.
9
Page 40
KNEEEEE
E
6
8
LEE
E
5
Assembly Instructions
E
E
Step 8
Attaching runners
Fix runner left and right side
B K and N on left & right
drawer side 6 and 8 as
shown using 12,5mm pozi
screw E.
Step 9
3x
Attaching drawer handle
Attacht drawer handle L on
drawer front 5 as shown
using 12,5mm pozi screw E.
Step 10
Inserting drawers
3x
10
Loading...