Page 1
MADE IN
BRITAIN
Dimensions
Width - 49cm
Depth - 39cm
Height - 43cm
Camden - Bedside
Assembly Instructions - Please keep for future reference
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Issue 2 - 12/12/13
Important - Please read these instructions fully before starting assembly
305/0679
305/0662
183/6314
Page 2
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: This unit weighs
approximately 11kgs. Please lift
with care.
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: If there is any
chance of this unit being pulled
over by children etc. it is
recommended that the unit is
secured to a wall using suitable
fixings (not supplied).
• Dispose of all packaging
carefully and responsibly.
1
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.
Page 3
Components - Panels
Please check you have all the panels listed below
2
1 2
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
5
6
10
3
7 8 9
Top (D1985A)
(489 x 391mm)
Left Side (D1986A)
(396 x 389mm)
4
Plinth (D1988A)
(413 x 96mm) x 2
Drawer Front (D1989A)
(410 x 173mm)
Horizontal (D1990A)
(413 x 367mm)
Drawer Base (T536)
(374 x 317mm)
Right Side (D1987A)
(396 x 389mm)
11
Left Drawer Side (W516LH)
(320 x 95mm)
Right Drawer Side (W516RH)
(320 x 95mm)
Drawer Back (W536)
(363 x 95mm)
Back (X942)
(430 x 148mm)
Page 4
Please check you have all the fittings listed below
3
Components - Fittings
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
A
Wooden dowel (F22) x 4
B
Metal dowel (F901) x 10
C
D
Large locking
nut (F900) x 8
E
Small locking
nut (F3) x 2
F
G
Small metal dowel (F893) x 4
H
19mm Screw (F461) x 2 Handle (F266) x 1
I
Nail (F51) x 7
J K
Hollow core
locking nut
(F892) x 4
N
Wedgefix (F639) x 4
L
Knock-in Peg (F171) x 4
13mm Screw (F63) x 6
13mm Screw (F52) x 6
M
R Runner (F160) x 1
b
L Runner (F161) x 1
M
c
L Runner (F159) x 1
M
a
R Runner (F162) x 1
M
d
304mm
Page 5
Assembly Instructions
4
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
B
B
B
6
Prepare the drawer
front
Screw 2 metal dowels
into the drawer front .
Note: Tighten the metal
dowels up fully against
the panels.
B
6
Prepare the drawer
sides
Insert a small locking
nut into the hole
shown on the left drawer
side and right drawer
side .
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
F
7
8
Attach the drawer
sides to the drawer
front
Push the left drawer side
. and right drawer side
. onto the back of the
drawer front .
Turn the small locking
nuts on the left
drawer side and right
drawer side .
Note: Turn the locking
nuts clockwise to
secure panels - more
than 1/2 a turn.
7
8
6
F
F
7
8
F
F
F
7
8
B
B
F
6
Small groove
7
8
Note: Due to the manufacturing process, the holes for the
locking nut can be on either surface of the drawer sides.
Note: The locking nuts can be on
either surface of the drawer sides.
Make sure that the small groove
is on the inside, as shown.
Step 2
Step 3
Step 1
Page 6
Assembly Instructions
5
Step 4
Fit the drawer base
Slide the drawer base
down the grooves in the
drawer sides and
and down into the
groove in the drawer
front .
Step 5
Fit the drawer back
Fit the drawer back
between the drawer
sides and .
Make sure that the
drawer base fits into
the groove in the drawer
back .
Hold the drawer back
in position and tap the
knock-in pegs
through the holes in the
drawer sides and .
Step 6
10
7 8
6
9
7 8
10
9
9
L
7 8
Attach the handle
Attach the handle
to the drawer front
using 2 screws .
6
6
88
7
10
6
88
10
7
L
L
L
L
I
H
9
H
H
I
6
Page 7
Assembly Instructions
6
Step 7
Step 8
Fit the wedgefixes
Turn the drawer
assembly over and fit the
4 wedgefixes .
Slide 2 wedgefixes
into the small groove
located on the back of
the drawer front and
2 wedgefixes into the
small groove in the
drawer back .
Once in place, tighten up
the screws in the
wedgefixes .
N
N
6
9
N
Fit runners to the
drawer
Fit the runner to the
bottom edge of the left
drawer side , as
shown, making sure that
it is pushed up against
the back of the drawer
front . Use a bradawl
to mark the fixing
positions, then secure
with 2 screws .
Fit the runner to the
bottom edge of the right
drawer side using the
same method.
8
M c
7
6
J
M d
N
N
N
N
J
J
J
J
Runners must be
pushed up against
the drawer front
M d
M c
6
9
8
7
6
N
Page 8
Assembly Instructions
7
Step 9
Prepare the left side
a: Fit the runner to
the left side .
The 1st screw uses
the 2nd hole in from the
front of the runner .
The 2nd and 3rd screw
use the holes that line up
with the other panel
holes.
b: Fit a screw into
the 2nd hole in at the top
of the runner .
Push 2 hollow core
locking nuts into the
left side , making sure
that they are flush
against the panel’s
surface.
Using a hammer, tap in
the pin on the hollow
core locking nut .
Note: The pin should be
tapped in flush with the
top surface of the hollow
core locking nut .
Screw 4 metal dowels
into the holes on the left
side .
1
K
a:
b:
C
C
C
C
C
1
C
B
1
M a
K
Finished front edge
K
1st
screw
2nd
screw
K
3rd
screw
M a
M a
M a
Finished front edge
J
K
J
M a
Finished
front edge
Finished
front edge
K
M a
K
K
J
C
C
B
B
B
B
1
1
Page 9
Assembly Instructions
8
Step 10
K
K
M b
K
J
C
C
B
B
B
B
Prepare the right side
a: Fit the runner to
the right side .
The 1st screw uses
the 2nd hole in from the
front of the runner .
The 2nd and 3rd screw
use the holes that line up
with the other panel
holes.
b: Fit a screw into
the 2nd hole in at the top
of the runner .
Push 2 hollow core
locking nuts into the
right side , making
sure that they are flush
against the panel’s
surface.
Using a hammer, tap in
the pin on the hollow
core locking nut .
Note: The pin should be
tapped in flush with the
top surface of the hollow
core locking nut .
Screw 4 metal dowels
into the holes on the
right side .
2
K
C
C
2
C
B
2
M b
M b
K
J
M b
2
2
Finished
front edge
Finished
front edge
a:
b:
M b
K
Finished front edge
K
1st
screw
2nd
screw
K
3rd
screw
M b
Finished front edge
J
C
C
C
Page 10
Finished
front edge
Finished
front edge
Assembly Instructions
Step 11
G
G
3
Prepare the top
Screw 4 small metal
dowels into the holes
on the top .
Note: Tighten metal
dowels up fully against
the panels.
G
G
G
G
Front edge
3
Step 12
Fit the top to the right
side
Attach the top to the
right side .
Note: You will need to
slide the 2 small metal
dowels into the top
of the 2 hollow core
locking nuts .
Insert a screwdriver into
the 2 hollow core locking
nuts and turn the nuts
inside as far as they will
go.
3
G
C
C
2
G
C C
3
2
9
Page 11
Assembly Instructions
10
Step 13
plain chipboard surface
4
E
E
E
E
Finished
front edge
Prepare the horizontal
Insert 4 large locking
nuts into the
horizontal .
Note: The arrow on the
locking nuts must point
towards the hole in the
edge of the panel.
E
4
E
Finished
front edge
Fit the horizontal
Push the horizontal
onto the right side .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the horizontal .
Note: Turn the large
locking nuts as far as
they will go - more than
1/2 a turn.
B
E
4
E
plain chipboard surface
4
4
2
E
Step 14
Page 12
Assembly Instructions
Step 15
11
Step 16
Prepare the 2 plinths
Tap 2 wooden dowels
into each of the 2 plinths
. .
Note: Wooden dowels
must not stick out from
the edge by more than
10mm or they may
damage other panels.
Insert 2 large locking
nuts into each plinth.
A
10mm
A
E
5
E
E
A
A
5
plain chipboard surface
x 2
Fit the 2 plinths
2 people are needed
here
One at a time, attach
each of the 2 plinths
onto the right side as
shown. Use a
screwdriver to tighten
the 2 large locking
nuts fitted to the
plinths.
Note: Turn the large
locking nuts as far as
they will go - more than
1/2 a turn,
5
2
E
E
plain chipboard surface
plain chipboard surface
5
5
2
Note: Support the
plinths until the left
side has been fitted
in the next step.
Page 13
Assembly Instructions
12
Step 17
5
5
Fit the left side
2 people are
needed here
Push the left side
onto the assembly.
Note: You will need to
slide the 2 small metal
dowels fitted to the
top into the top of
the 2 hollow core locking
nuts .
Insert a screwdriver into
the 2 hollow core locking
nuts and turn the nuts
inside as far as they will
go.
Use a screwdriver to
tighten the 4 large
locking nuts fitted to
the horizontal and
the 2 plinths .
Note: Turn the large
locking nuts as far as
they will go - more than
1/2 a turn.
1
G
C
C
3
E
E
4
5
1
3
4
Page 14
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
and quote the reference numbers on the component pages.
Argos Ltd, 489-499 Avebury Boulevard, Central Milton Keynes, MK9 2NW
Assembly Instructions
14
Step 18
Side panel
Drawer
y
y
x
x
b:
Fit the back
a: Square up the unit by
making sure that
measurement x to x
equals y to y.
b: Place the back
onto the unit.
Nail around the
outside edges of the
back .
Stand the unit up for
the next step.
11
D
The measurement from top corner X to bottom corner X must be
equal to the measurement from top corner Y to bottom corner Y
a:
11
D
11
Fit the drawers
Slide the wheels of the
runners fitted to the
drawers, over the wheels
of the runners fitted to
the side panels and push
the drawers into position.
Assembly is complete
Step 19
Page 15
Page 16
ALR2836
Loading...