Hygena 656-5855 Instruction manual

MADE IN

BRITAIN

Cabinet

Black Drawer Pack

Cream Drawer Pack

Oak Drawer Pack

White Gloss Drawer Pack

White HN Drawer Pack

Dimensions

Width - 60cm

Depth - 59cm

Height - 87cm

Valencia - 3 Drawer Cabinet

Assembly Instructions - Please keep for future reference

If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800

Issue 2 - 31/07/14

Important - Please read these instructions fully before starting assembly

hygena

656/5855

656/6469

656/6483

204/7834

656/6476

198/6264

Safety and Care Advice

Important - Please read these instructions fully before starting assembly

• Warning: This unit weighs approximately 18kgs. Please lift with care.

• Check you have all the components and tools listed on pages 2, 3 and 4.

• Remove all fittings from the plastic bags and separate them into their groups.

• Keep children and animals away from the work area, small parts could choke if swallowed.

• Parts of the assembly will be easier with 2 people.

• Make sure you have enough space to layout the parts before starting.

• Do not stand or put weight on the product, this could cause damage.

• Assemble the item as close to its final position (in the same room) as possible.

• Assemble on a soft level surface to avoid damaging the unit or your floor (use opened out unit carton).

• We do not recommend the use of power drill/drivers for

inserting screws, as this could damage the unit. Only use hand screwdrivers.

• Safety note: If there is any chance of this unit being pulled over by children etc. it is recommended that the unit is secured to a wall using suitable fixings (not supplied).

• Dispose of all packaging carefully and responsibly.

Care and maintenance

• Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners.

• From time to time check that there are no loose screws on this unit.

• This product should not be discarded with household waste. Take to your local authority waste disposal centre.

Note: If required the next page can be cut out and used as reference throughout the assembly. Keep this page with these instructions for future reference.

Components - Panels

Please check you have all the panels listed below

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Left Side (DPF087A)

(720 x 560mm)

Right Side (DPF088A)

(720 x 560mm)

Back (DPF081A)

(579 x 680mm)

Standard Drawer Back

(DPF133A) (539 x 98mm)

Pan Drawer Back

(DPF132A) (539 x 173mm) x 2

Drawer Base (DPF131A)

(539 x 448mm) x 3

Base (DPF078A)

(569 x 494mm)

Standard Drawer Front (DPF121A)

(596 x 176mm)

Pan Drawer Front (DPF122A)

(596 x 266mm) x 2

410

Cross Rail (DPF080A)

(569 x 96mm) x 2

NOTE: The front surface of

the drawer fronts are

protected with a peel-off film

Please check you have all the fittings listed below

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.

Wooden dowel (F22) x 10

Metal dowel (F901) x 8

Large locking nut (F900) x 8

G H I a

I c

I d

I e

I b

J K

13mm Screw (F63) x 54

13mm Screw (F79) x 6

Connecting Sleeve (F432) x 2 19mm Connecting bolt (F461) x 2

L M

N O

25mm Screw (F50) x 5

Bracket (F945) x 4

Leg Bracket (F127) x 2

Leg Socket (F120) x 4

Leg Clip (F128) x 2

16mm Screw (F129) x 16

Leg (F122) x 4

13mm Screw (F52) x 36

Left Runner (F139) x 3

Left Soft Close Unit (F141) x 3

Right Soft Close Unit (F142) x 3

Left Soft Close Catch (F143) x 3

Right Soft Close Catch (F144) x 3

Right Runner (F140) x 3

Components - Fittings

Ruler - Use this ruler to help correctly identify the screws

mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170

Fittings continue on the next page

Please check you have all the fittings listed below

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Tools required

Rule Scissors Hammer

Eye protection (when using a hammer or drill)

Cross-head screwdriver

Ruler - Use this ruler to help correctly identify the screws

mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170

Electric drill

U a

Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.

U b

25mm Screw (F132) x 6

T c

T d

T a T b

Pan Bar Holder (F151) x 4

Pan Bar Socket

(F148) x 4

15mm Screw

(F150) x 12

Pan Bar (F152) x 4

Left Drawer Side (F145) x 3

Right Drawer Side (F146) x 3

Components - Fittings

Handle (F214) x 3

Assembly Instructions

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Step 1

Fit the left runners to the left side

Fit the 3 left runners marked ‘L’ to the left side .

The 1st screw uses the 2nd hole in from the front of the runner.

The 2nd screw uses the 4th hole in from the back of the runner.

The 3rd screw uses the 8th hole in from the back of the runner.

Fit left soft close units to the left side

Fit the 3 left soft close units . marked ‘L’ to the left side using 3 screws .

Step 2

+ 14 hidden pages