Hygena 656-5790, 633-2882, 633-2710, 656-5295, 656-4540 Instruction manual

...

MADE IN

BRITAIN

Assembly Instructions - Please keep for future reference

Dimensions

Width - 100cm

Depth - 59cm

Height - 87cm

Valencia - 1000mm Base Cabinet

If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800

Issue 1 - 16/08/11

Important - Please read these instructions fully before starting assembly

hygena

656/5790

633/2882

633/2710

656/5295

656/4540

633/2806

Cabinet

Black Door Pack

Cream Door Pack

Grey Door Pack

Plum Door Pack

White Door Pack

Safety and Care Advice

Important - Please read these instructions fully before starting assembly

• Warning: This unit weighs approximately 26kgs. Please lift with care.

• Check you have all the components and tools listed on pages 2, 3 and 4.

• Remove all fittings from the plastic bags and separate them into their groups.

• Keep children and animals away from the work area, small parts could choke if swallowed.

• Parts of the assembly will be easier with 2 people.

• Make sure you have enough space to layout the parts before starting.

• Do not stand or put weight on the product, this could cause damage.

• Assemble the item as close to its final position (in the same room) as possible.

• Assemble on a soft level surface to avoid damaging the unit or your floor (use opened out unit carton).

• We do not recommend the use of power drill/drivers for

inserting screws, as this could damage the unit. Only use hand screwdrivers.

• Safety note: If there is any chance of this unit being pulled over by children etc. it is recommended that the unit is secured to a wall using suitable fixings (not supplied).

• Dispose of all packaging carefully and responsibly.

Care and maintenance

• Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners.

• From time to time check that there are no loose screws on this unit.

• This product should not be discarded with household waste. Take to your local authority waste disposal centre.

Note: If required the next page can be cut out and used as reference throughout the assembly. Keep this page with these instructions for future reference.

Tools required

Rule Scissors Hammer

Eye protection (when using a hammer or drill)

Cross-head screwdriver

Electric drill

Components - Panels

Please check you have all the panels listed below

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Left Side (DPF068A)

(720 x 560mm)

Right Side (DPF069A)

(720 x 560mm)

Loose Shelf (DPF083A)

(968 x 431mm)

Base (DPF082A)

(969 x 494mm)

Back (DPF085A)

(979 x 680mm)

Cross Rail (DPF084A)

(969 x 96mm) x 2

Muntin Rail (DPF086A)

(36 x 688mm)

Valencia Door (DPF147B)

(497 x 716mm) x 2

The front surface

of this door is

protected with a

peel-off film

Please check you have all the fittings listed below

Components - Fittings

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.

Wooden dowel (F22) x 12

Metal dowel (F901) x 8

Large locking nut (F900) x 8

G H I a

I c

I d

I e

I b

Ruler - Use this ruler to help correctly identify the screws

mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170

J K

13mm Screw (F63) x 8

13mm Screw (F79) x 6

Connecting Sleeve (F432) x 2 19mm Connecting bolt (F461) x 2

L M

25mm Screw (F50) x 6

Hinge Cover (F119) x 4

Bracket (F945) x 4

Shelf support (F110) x 6

Hinge Plate (F117) x 4

Hinge Arm (F118) x 4

Leg Bracket (F127) x 3

Leg Socket (F120) x 5

Leg Clip (F128) x 3

16mm Screw (F129) x 21

Leg (F122) x 5

ygen

40mm Screw (F910) x 2

PPa

25mm Screw (F132) x 4

Handle (F214) x 2

Assembly Instructions

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Step 1

5mm

150mm

Only screw ONE metal dowel into

one of these holes.

1st 5mm hole

2nd 5mm hole

Prepare the left side

Fit 2 hinge plates onto the left side , orientated as shown.

Screw 3 metal dowels into the holes shown on the left side .

Fit a bracket flush to the top edge of the left side , about 150mm in from the groove, see diagram.

Secure the bracket using screw .

Fit another bracket flush to the back edge of the left side , about 5mm down from the top edge, see diagram.

Secure the bracket using screw .

Note: The brackets must be flush with the top/back edge of the panel.

Step 2

Prepare the left side

Screw a metal dowel into one of the holes shown on the left side . .

Note: Tighten metal dowels up fully against the panels.

If you ARE fitting a sink unit we recommend that you use the 2nd 5mm hole.

If you ARE NOT fitting a sink unit we recommend that you use the 1st 5mm hole.

Assembly Instructions

Step 3

Prepare the right side

Screw a metal dowel into one of the holes shown on the right side . .

Use the same hole that you used for the left side in step 1.

Prepare the right side

Fit 2 hinge plates onto the right side , orientated as shown.

Screw 3 metal dowels into the holes shown on the right side .

Fit a bracket flush to the top edge of the right side , about 150mm in from the groove, see diagram.

Secure the bracket using screw .

Fit another bracket flush to the back edge of the right side , about 5mm down from the top edge, see diagram.

Secure the bracket using screw .

Step 4

Only screw ONE metal dowel

into one of these holes (use

the same hole that you used

for the left side in step 1).

+ 14 hidden pages