Hygena 6031255 Instruction manual

602/3919

Assembly Instructions – Please keep for future reference

Important – Please read these instructions fully before starting assembly

If you need help or have damaged or missing parts, call the Customer Helpline: 01799 513466

Issue 1 - 02/11/09

Savannah Dining Table

EXTENDED

CLOSED

Dimensions

Width - 200cm

Depth - 80cm

Height - 75cm

Width - 140cm

Depth - 80cm

Height - 75cm

Extended

Closed

603/1217

Safety and Care Advice

Important – Please read these instructions fully before starting assembly

Glass safety

Care and maintenance

• This product complies with BS7376: 2004.

• Imported by: Justwise Group Ltd 6 The Shires Shirehill Industrial Estate Saffron Walden Essex CB11 3AP

• Product stock ref: DTSAV (Clear Glass)

DTSAVB (Black Glass)

• P/O No:

• If the glass is chipped or broken, stop using the product and consult the Manufacturer of Supplier.

WARNINGS

a) Do not place very hot or very cold items on the glass surface(s) unless adequately thick table mats are used to prevent such items from coming into contact with the glass..

b) Do not sit or stand upon the glass surface(s).

c) Do not use the glass as a chopping surface. Do not strike the glass with hard or pointed items.

d) When cleaning glass panels use a damp cloth or leather with washing up liquid or soft soap if necessary, do not use washing powders or any other substance containing abrasives since these substances scratch glass.

• Only clean using a damp cloth

and mild detergent, do no use bleach or abrasive cleaners.

• From time to time check that there are no loose screws on this unit.

• This product should not be discarded with household waste. Take to your local authority waste disposal centre.

• Check you have all the components and tools listed on pages 2 and 3.

• Remove all fittings from the plastic bags and separate them into their groups.

• Keep children and animals away from the work area, small parts could choke if swallowed.

• Make sure you have enough space to layout the parts before starting.

• Do not stand or put excessive

weight on the product, this could cause damage.

• Assemble the item as close to its final position (in the same

room) as possible.

• Parts of the assembly will be

easier with 2 people.

• Dispose of all packaging

carefully and responsibly.

• Place the product on flat and

steady surface during use.

• Assemble on a soft level surface to avoid damaging the unit or your floor.

• Keep these instructions for further use.

• To ensure an easier assembly, we strongly advise that all fittings are only finger tightened during initial assembly. Only upon completion of the assembly should all fixing points be fully tightened.

Please check you have all the parts listed below

Components - Parts

Leg frame x 2

(70 x 12.6cm)

Top frame (138 x 60.7cm)

Glass extension leaves x 2 (80 x30cm)

Leg x 4

(54.8 x Ø5.1cm)

Glass top (140 x 80cm)

Components - Fittings

Ruler – Use this ruler to help correctly identify the screws

10 2015 4035

25 80

7060 65

160155150140 145120 125

130 135

85 90 10095 115110105 165 170

Please check you have all the fittings listed below

Note:

The quantities below are the correct amount to complete the assembly. In some cases more

fittings may be supplied than are required.

If you have damaged or missing components, call the Customer Helpline: 01799 513466

0010 20 40

80706050 150140120

130

90 100 110

1 2

Tools required

Ruler/tape measure

B C

D E F

75mm Large stud x 4

Nut x 4

Spanner x 1

K L M

N O P

Leg spacer x 4

13mm Allen screw x 16

Spring washer x 8

Ø16mm Plain washer x 8

68mm Medium stud x 4

Nut x 4

15mm Short stud x 8

10mm Threaded spacer x 4

Rubber washer x 8

14mm Threaded spacer x 8

Ø18mm Plain washer x 4

Rubber pad x 4 Allen key x 1

Step 1

Assembly Instructions

Step 2

Assembling leg frames

Place leg frame upside down onto the floor.

Screw large threaded rods into leg frames

as shown.

Note:

Screw the short

end in until it stops.

Locate leg spacers over the threaded rods.

Screw legs onto

threaded rods and tighten.

Repeat for other leg frame.

Assembling side rails

Place top frame upside down onto a clean flat surface.

Assemble leg frames to the top frame using

fixings and .

C D

25mm

Upside down

Assembly Instructions

Step 3

Step 4

Preparing glass top

Place glass top upside down onto a clean flat surface.

Screw medium threaded rods into the metal discs on the underside of glass top .

Screw nuts onto

threaded rods and use the spanner to tighten

onto the metal discs.

Screw threaded spacers

half way onto the threaded rods.

Preparing extension leaves

Step 3 completed

Step 4 completed

Place extension leaves

upside down onto a

clean flat surface.

Screw short threaded rods into the metal discs on the underside of extension leaves .

Locate rubber washers

over the rods.

Screw threaded spacers

onto the rods and tighten.

+ 13 hidden pages