Hygena 6031224 Instruction manual
602/3919
Assembly Instructions – Please keep for future reference
Important – Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline: 01799 513466
Issue 1 - 02/11/09
Savannah Dining Table
EXTENDED
CLOSED
Dimensions
Width - 200cm
Depth - 80cm
Height - 75cm
Width - 140cm
Depth - 80cm
Height - 75cm
Extended
Closed
603/1217
Safety and Care Advice
Important – Please read these instructions fully before starting assembly
1
Glass safety
Care and maintenance
1
• This product complies with
BS7376: 2004.
• Imported by:
Justwise Group Ltd
6 The Shires
Shirehill Industrial Estate
Saffron Walden
Essex
CB11 3AP
• Product stock ref: DTSAV (Clear Glass)
DTSAVB (Black Glass)
• P/O No:
• If the glass is chipped or broken, stop using the product and
consult the Manufacturer of Supplier.
WARNINGS
a) Do not place very hot or very cold items on the glass surface(s) unless adequately thick table mats
are used to prevent such items from coming into contact with the glass..
b) Do not sit or stand upon the glass surface(s).
c) Do not use the glass as a chopping surface. Do not strike the glass with hard or pointed items.
d) When cleaning glass panels use a damp cloth or leather with washing up liquid or soft soap if
necessary, do not use washing powders or any other substance containing abrasives since these
substances scratch glass.
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put excessive
weight on the product, this
could cause damage.
• Assemble the item as close
to its final position (in the same
room) as possible.
• Parts of the assembly will be
easier with 2 people.
• Dispose of all packaging
carefully and responsibly.
• Place the product on flat and
steady surface during use.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor.
• Keep these instructions for
further use.
• To ensure an easier assembly,
we strongly advise that all
fittings are only finger tightened
during initial assembly. Only
upon completion of the
assembly should all fixing points
be fully tightened.
Please check you have all the parts listed below
Components - Parts
2
Leg frame x 2
(70 x 12.6cm)
Top frame (138 x 60.7cm)
Glass extension leaves x 2 (80 x30cm)
3
5
4
1
Leg x 4
(54.8 x Ø5.1cm)
2
Glass top (140 x 80cm)
Components - Fittings
A
0
Ruler – Use this ruler to help correctly identify the screws
3
5
10 2015 4035
30
25 80
75
7060 65
45
50
55
160155150140 145120 125
130 135
85 90 10095 115110105 165 170
Please check you have all the fittings listed below
Note:
The quantities below are the correct amount to complete the assembly. In some cases more
fittings may be supplied than are required.
If you have damaged or missing components,
call the Customer Helpline: 01799 513466
0010 20 40
30
80706050 150140120
130
90 100 110
1 2
4
3
5
6
Tools required
Ruler/tape
measure
B C
D E F
G
75mm Large stud x 4
Nut x 4
Spanner x 1
H
J
K L M
N O P
Q
Leg spacer x 4
13mm Allen screw x 16
Spring washer x 8
Ø16mm Plain washer x 8
68mm Medium stud x 4
Nut x 4
15mm Short stud x 8
10mm Threaded spacer x 4
Rubber washer x 8
14mm Threaded spacer x 8
Ø18mm Plain washer x 4
Rubber pad x 4 Allen key x 1
Step 1
Assembly Instructions
4
Step 2
Assembling leg frames
Place leg frame
upside down onto the
floor.
Screw large threaded
rods into leg frames
as shown.
Note:
Screw the short
end in until it stops.
Locate leg spacers
over the threaded rods.
Screw legs onto
threaded rods and
tighten.
Repeat for other leg
frame.
A
Assembling side rails
Place top frame
upside down onto a
clean flat surface.
Assemble leg frames to
the top frame using
fixings and .
3
C
B
C D
3
1
1
2
25mm
B
AA
Upside down
D
E
3
D
E
C
1
2
E
Loading...