Page 1
Nitro Bar Stool
Assembly Instructions - Please keep for future reference
hygena
528/7316
523/8846
539/6324
Dimensions
Width - 44cm
Depth - 53.5cm
Height - 92.5-113.5cm
Important - Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline:
Argos = 0345 640 0800
Issue 1 - 18/04/16
Page 2
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Check you have all the
components and tools listed on
the following pages.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• During assembly do not stand
or put weight on the product, this
could cause damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor.
• Parts of the assembly will be
easier with 2 people.
• Do not stand on the chair.
• Do not use this chair as step
ladder.
• This product should not be
discarded with household
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Unit weight: 7.6kgs.
• Maximum safe weight of user:
110kgs.
waste. Take to your local
authority waste disposal centre.
Handy Hints
• Assemble all parts and bolts
loosely during assembly, only
once the product is complete
should you fully tighten the
bolts.
• Regularly check and ensure
that all bolts and fittings are
tightend properly.
1
Page 3
If you have damaged or missing components, call the
Components - Parts
Customer Helpline: Argos = 0345 640 0800
Please check you have all the parts listed below
1
Seat
(44 x 51 x 37cm)
4
Decor ring
(Ø7.5 x 2.2cm)
2
Upper leg
(32 x 27 x 39.5cm)
5
Base
(Ø45 x 8.5cm)
3
Gaslift
(Ø5 x 52-73cm)
Components - Fittings
Please check you have all the fittings listed below
Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings
may be supplied than are required.
A
B
C
M6 x 18mm Bolt x 4
Washer x 4
Ruler - Use this ruler to help correctly identify the screws
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100
105
Allen key x 1
110 115 120 125 130 135 140 145 150 155 160 165 170
2
Page 4
Assembly Instructions
Step 1
Attaching upper leg
Place the seat upside
down on a flat protected
surface. Position the
upper leg and make
sure that the arrow on
the plate is pointing
towards the front edge of
the seat as shown in the
inset diagram. Secure
using washer and
A
bolt .
1
2
B
Lever
Arrow
2
2
A
A
B
B
1
A
A
B
B
1
A
B
Step 3
Step 2
Attaching gaslift
Place the base on a
5
flat protected surface.
Position the decor ring
on the base and insert
the gaslift into the
3
decor ring and hole of
the base.
Important:
Remove plastic
tip cover on
gaslift before
assembling.
Plastic tip
4
3
4
5
3
Page 5
Assembly Instructions
Step 3
Step 3
Attaching the seat
Position the seat as
shown and insert the
gaslift into the upper
leg .
Secure by pressing down
the seat firmly.
3
2
2
3
Gaslift operation
To adjust the seat higher,
lift up the lever under the
seat and release at
desired height.
To lower the seat, lift up
the lever while seated on
the stool.
Assembly is complete.
Lever
If you need help or have damaged or missing parts, call the Customer Helpline:
Argos = 0345 640 0800
4
Loading...