Page 1
Hygena Cubic Wood Glass Low SB/TV Unit
Assembly Instructions - Please keep for future reference 482/0688D
Dimensions
Width - 120cm
Depth - 38cm
Height - 61.8cm
Important – Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline: 03456 400800
Issue 1 - 16/09/15
Page 2
Safety and Care Advice
Important – Please read these instructions fully before starting assembly
• Check you have all the
components and tools listed on
pages 2 & 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close
to its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor.
• Parts of the assembly will be
easier with 2 people.
as this could damage the unit.
Only use hand screwdrivers.
• Dispose of all packaging
carefully and responsibly.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
Glass safety – Take care when handling glass, please follow the advice below
• •
•
If a glass component is
chipped or broken replace with
glass of the type described on
this instructions. Consult the
manufacturer, retailer or agent
with regard to obtaining a
manufacturing specification and
shape for replacement glass
quoting the model number, and
batch or date of manufacture.
Do not place very hot or
cold items against or in close
proximity to the glass
surfaces unless adequately
thick insulating material is
used to prevent such items
coming into contact with the
glass.
•
Do not strike the glass with
hard or pointed items.
When cleaning glass panels
or mirrors use a damp cloth or
leather with washing up liquid or
soft soap if necessary.
•
Do not use washing powders
or any other substances
containing abrasives since these
substances scratch glass.
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Note: if require the next
page can be cut out and used
as reference throughout the
assembly. Keep this page with
these instructions for future
reference.
1
Page 3
Components - Panels
Please check you have all the panels listed below
Top panel
1
(1200 x 380 mm)
Left divider
4
(600 x 359mm)
Rear rail
7
(360 x 60mm)
Left side panel
2
(376 x 600 mm) (376 x 600mm)
Right divider
5
(600 x 359mm) (1078 x 60mm)
Bottom panel x 2
8
(329 x 358mm) (548 x 337mm)
Right side panel
3
Front top rail
6
Rear panel x 2
9
Left bottom rail
10
(359 x 60mm)
Left door
13
(474 x 355mm)
Right bottom rail
11
(359 x 60mm)
Right door
14
(474 x 355mm)
Adjustable shelf x 4
12
(339 x 327mm)
Glass shelf x 3
15
(359 x 355mm)
2
Page 4
If you have damaged or missing components,
12mm Screw
x
A
D
Shelf pin
x
16
110 115 120 125 130 135 140 145 150 155 160 165 170
105
Metal dowel
x
G
J
K
M
N
Components - Fittings
call the Customer Helpline: 03456 400800
Please check you have all the fittings listed below
Note: The quantities below are the correct amount to complete the assembly. In some cases more
fittings may be supplied than are required.
B C
Wood dowel x 28
Metal cam x 30
Cover pad x 30
Handle x 2
Corner block x 8
Tools required
E
Shelf holder x 12
H I
Hinge x 4
Large foot pad x 4
14 mm Screw x 8
Phillips screwdriver
(medium & small)
16
30
F
14 mm Screw x 16
L
Small foot pad x 4
Flatblade screwdriver
Ruler - Use this ruler to help correctly identify the screws
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100
3
Page 5
Assembly Instructions
Step 1
Screw 8 Metal dowels
C
into the threaded holes
in the Left and Right side
panels and Left
and Right divider
2 3
5
4
as shown.
Insert Wood dowels
A
into the indicated holes.
C
A
3
2
C
A
5
4
Step 2
Firmly push Right side
panel and Right
divider onto the ends
of Bottom panel ,
ensuring the Metal
dowels and wood
dowels enter
corresponding holes.
Firmly push Left side
panel and Left
divider 4 onto the ends
of Bottom panel ,
ensuring the Metal
dowels and wood
dowels enter
corresponding holes.
3
5
8
C
A
2
4
8
C
A
3
5
2
8
4
8
4
Page 6
Assembly Instructions
Step 3
Insert the 8 Metal cams
D
into the 8 holes on
the Bottom panels
so that they are flush.
Note: Longer
leg of the cross
on the Metal
Cams must face towards
end of panels (as shown).
Then, using a Philips
Screwdriver, screw all
Metal cams
D
clockwise until they are
‘hand tight’.
8
2
3
5
4
8
8
D
Step 4
Screw 2 Metal dowels
into the threaded holes
in the Left and Right
divider as
4 5
shown.
Insert Wood dowels
into the indicated holes.
Firmly push Left and
Right side piece from
Step 3 onto the ends of
Rear rail , ensuring
7
the Metal dowels and
wood dowels enter
A
corresponding holes.
C
A
C
Note: Longer leg of
the cross on the
D
Metal Cams must
face towards end
of panel.
5
A
7
A
4
C
C
5
Page 7
Assembly Instructions
Step 5
Insert the 2 Metal cams
D
into the 2 holes on
the Rear rail so that
they are flush.
Cams must face towards
end of rail (as shown).
Then, using a Philips
Screwdriver, screw all
Metal cams
clockwise until they are
‘hand tight’.
7
Note: Longer
leg of the cross
on the Metal
D
D
D
D
Step 6
Screw 8 Metal dowels
into the threaded holes
in the Front top and
bottom rails
6
101111
as shown.
Insert Wood dowels
into the indicated holes.
Firmly push the Front top
and bottom rails onto
the top edges of side
panels and dividers,
ensuring the Metal
dowels and wood
dowels enter
C
A
corresponding holes.
C
A
C
A
C
A
6
10
Taped edge.
6
11
10
Taped end.
6
Page 8
Assembly Instructions
Step 7
Insert the 8 Metal cams
D
into the 8 holes on
the side panels and
dividers so that they are
flush.
Note: Longer
leg of the cross
on the Metal
Cams must face towards
metal dowels.
D
D
D
D
D
D
Then, using a Philips
Screwdriver, screw all
Metal cams
D
clockwise until they are
‘hand tight’.
Step 8
Screw 12 Metal dowels
into the threaded holes
in the Top panel as
1
shown.
Insert Wood dowels
into the indicated holes.
Slide Rear panels
into the grooves in the
side panels and dividers.
Firmly push the Top
panel onto the end
1
of side panels and
dividers, ensuring the
rear panels enter all
the grooves, and
ensuring the Metal
dowels and wood
dowels enter
C
A
corresponding holes.
C
A
9
D
D
C
C
A
1
1
9
9
7
Page 9
Assembly Instructions
Step 9
Insert the 12 Metal cams
D
into the 12 holes on
the side panels, dividers
and front rail so that they
are flush.
Note: Longer
leg of the cross
on the Metal
Cams must face towards
metal dowels.
Then, using a Philips
Screwdriver, screw all
Metal cams
clockwise until they are
‘hand tight’.
D
D
DD
Step 10
Screw 12 Shelf holders
onto the pre-drilled holes
in dividers using 12mm
Screws , make sure
the screws of the shelf
holders face downwards
as shown.
B
E
E
B
8
Page 10
Assembly Instructions
Step 11
Push the top Glass shelf
15
into the Shelf
holders and secure
with the screws by
turning clockwise as
shown.
Repeat this step to
assemble the other two
glass shelves.
Peel off the cover of the
Foot pads , attach
to the bottom edges of
side panels and dividers
as shown.
Turn the unit upright.
E
L
K
15
Step 12
Screw Handle to the
pre-drilled holes in the
rear face of the Door
using 12mm Screws .
Screw Hinges to the
pre-drilled holes in the
rear face of the Door
using 14mm Screws .
Repeat this step to
assemble Handle and
Hinges onto the other
door.
J
14
B
H
F
L
K
B
Front
J
F
14
H
9
Page 11
Assembly Instructions
Step 13
Locate the Right side
door onto the Right
side panel , screw
the Hinges to the
14
3
H
pre-drilled holes, using
14mm Screws as
F
shown.
F
H
3
14
13
Step 14
Push 4 Shelf Pins
into each side of the
side panels and
dividers at desired
height.
Place Adjustable
shelves onto the
Shelf pins.
12
I
I
I
I
I
I
I
12
12
I
I
12
12
10
Page 12
Assembly Instructions
Step 15
Firmly push Corner
blocks into the
grooves in the coners
of rear panels on the
rear side as shown,
secure with 14mm
Screws .
Cover the visible
cam holes with Cover
pads .
M
N
M
G
M
M
M
M
N
M
M
Step 16
Adjust the door:
a: To move doors in
or out: loosen screw
shown and move doors
to suit.
Re-tighten screws.
b: To move doors left
or right: loosen screw
shown and move doors
to suit.
Re-tighten screws.
M
M
Assembly is complete.
If you need help or have damaged or missing parts, call the Customer Help Line: 03456 400800
Home Retail Group plc. Avebury, 489-499 Avebury Boulevard. Milton Keynes. MK9 2NW
11
Loading...