Page 1
Luna TV Unit
Assembly lnstructions - Please keep for future reference
hygena
464/9883
Dimensions
Width - 90cm
Depth - 40cm
Height -45.5cm
Important - Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline: 0345 6400 800
Issue 1-15-10-15
Page 2
Safety and Care Advice
Check you have all the
components and tools listed on
pages 2 and 3.
Remove all ttings from the
plastic bags and separate them
into their groups.
Keep children and animals
away from the work area, small
parts could choke if swallowed.
Make sure you have enough
space to layout the parts before
starting.
This product has been nished using natrual materials. As a living material, you may notice some
variation in the grain and colour shade between the dierent components.
Unlike a synthetic or man-made material which has a uniform nish, a feature of natural wood is its
variation in grain and colour. We wish to reassure you that this is quite normal and is not the result
of any manufacturing fault.
Assemble the item as close
to its nal position (in the same
room) as possible.
Assemble on a soft level
surface to avoid damaging the
unit or your oor.
Assembly requires 2 people.
Do not stand or put excessive
weight on the product,this could
cause damage.
We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers and
Allen keys.
Dispose of all packaging
carefully and responsibly.
Where sheets of wood are joined together, a line may be detected. Again, this is normal and is not
an imperfection.
The natural nish should be cared for by the periodic application of a good quality 'was' based
domestic furniture polish (Not silicone!!). Occasional / small spills should be removed immediately
using a damp cloth.
Do not allow hot articles to come into contact with the surface, as damage will occur!
Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
From time to time check that
there are no loose screws on
this unit.
This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
1
Page 3
Components - Parts
underside
1
Top (90x40x2.5cm)
inside
lf you have damaged or missing components.
call the Customer Helpline:
0345 6400 800
inside
Side frame (left)
2
(43x37x5cm)
3
Side frame (right)
(43x37x5cm)
Front stretcher
5
(74x5x1.5cm)
7
Drawer front (73.7x16x1.5cm)
4
Back panel
(77.8x35.8X0.3cm)
Rear stretcher
6
(74x5x1.5cm)
8
10
Drawer back (70.6x12x1.2cm)
Drawer base
(71.3x29.7x0.3cm)
9
Shelf (74x36.5x1.5cm)
11
Drawer support
(28.8x4x1.2cm)
12
Drawer side (left)
(30x12x1.2cm)
14
Apron
(74x5x2.5cm)
13
Drawer side (right)
(30x12x1.2cm)
2
Page 4
Components - Fittings
0345 6400 800
A
Wooden dowel x 14 (6X30mm)
D
Small locking nut x 9
G
Screw x 4 (3x12mm)
K
Screw x 2 (4x18mm)
Tools required
B C
Metal dowel x 17
E F
Screw x 19 (2.5x10mm)
H
Handle x 2
L
Bolt x 2 (4x10mm)
Large locking nut x 8
F
Drawer runners x 2
J
Screw x 8 (4x30mm)
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 105 110 115 120 125 130 135 140 145 150
0
1 2 3 4 5 6
Ruler/tape measure
Phillips screwdriver
(Not supplied)
Ruler - Use this ruler to help correctly identify the screws
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 105 110 115 120 125 130 135 140 145 150 155 160 165 170
3
Page 5
Assembly Instructions
Preparing panels
Place top , side frames
2
and , and drawer
1
3
7
.
Screw metal dowels into
all panels as shown.
N
o
e
t
:
Screw metal dowels as
far as shown. Do not
overtighten.
Insert wood dowels into
side frames and and
top as shown.
1
Assemble apron to top
using screws .
2
B
A
3
14
J
A
2
B
A
B
3
14
B
B
1
1
J
A
7
B
Assembling drawer runners
Assemble drawer runners
to side frames and
using screws
N
o
e
t
:
The drawer runners
holes shown. It will be necessary
to extend/close the runners to
gain access to the holes.
2
BG
BF
3
G
2
G
F
F
F
F
G
G
F
3
4
Page 6
Assembly Instructions
Assembling shelf and stretchers
a:
Locate shelf 9 into position
N
o
e
t
:
facing down.
Insert large locking nuts
into the underside of shelf
as shown.
Turn locking nuts clockwise
to secure.
9
BC
9
a:
9
BC
2
BC
b: Locate front and rear
stretchers and in the
locations shown.
N
o
t
are facing down.
Insert large locking nuts
into both stretchers as shown.
Turn locking nuts clockwise to
secure.
5
e
:
6
BC
5
b:
6
Front
BC
Back
BC
BC
5
Page 7
Assembly Instructions
4
Assembling side frame
Locate right side frame into
position.
Secure using large locking nuts
as shown.
BC
3
3
C
C
C
5
Assembing top
With help , carefully stand the
unit upright.
Insert wood dowels into
the top of side frames and
.
3
Locate top into position.
Insert small locking nuts into
side frames and .
Turn locking nuts clockwise to
secure.
1
2 3
BA
2
BD
1
2
A
D
3
D
6
Page 8
Assembly Instructions
6
Fitting back panel
Carefully turn the unit over
onto it’s face.
Locate back panel into
position with the cable access
hole at the top as shown.
Secure using screws
4
BE
Top
E
4
7
Page 9
Assembly Instructions
7
Assembling drawer
a: Locate drawer sides
and and support
12
onto drawer front .
N
o
Ensure the grooves on
all panels align at the bottom.
Insert small locking nuts
into the drawer sides and
support as shown.
Turn locking nuts clockwise to
secure.
Slide drawer base into
b:
the grooves.
13
7
e
t
:
11
BD
10
D
a:
12
11
13
D
D
D
7
Align grooves
b:
10
c:
Assemble drawer back
using screws .
Fit handles to drawer
d:
7
front using screws .
BJ
BH
BK
J
J
8
8
c:
d:
K
7
H
8
Page 10
Assembly Instructions
8
Locating drawer
With help, turn the whole unit
upright.
Extend the drawer runners fully
out.
Locate the drawer onto the
runners and secure using screws
as shown.
BL
L
L
L
If you need help or have damaged or missing parts, call the Customer Helpline: 0345 6400 800
Home Retail Group. 489-499 Avebury Boulevard. Saxon Gate West. Central Milton Keynes. MK9 2NW
9
Loading...