Page 1
Hygena Cantilever Chair
Assembly Instructions - Please keep for future reference
hygena
459/1553
468/9348
Dimensions
Width - 43cm
Depth - 57.5cm
Height - 103.5cm
Important - Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline:
Argos = 0345 640 0800
Issue 1 - 19/09/15
Page 2
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Check you have all the
components and tools listed on
the following pages.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• During assembly do not stand
or put weight on the product, this
could cause damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor.
• Parts of the assembly will be
easier with 2 people.
• Do not stand on the chair.
• Do not use this chair as step
ladder.
• This product should not be
discarded with household
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Unit weight: 6.32 kgs.
• Maximum safe weight of user:
110kgs.
waste. Take to your local
authority waste disposal centre.
Handy Hints
• Assemble all parts and bolts
loosely during assembly, only
once the product is complete
should you fully tighten the
bolts.
• Regularly check and ensure
that all bolts and fittings are
tightend properly.
1
Page 3
If you have damaged or missing components, call the
Components - Parts
Customer Helpline: Argos = 0345 640 0800
Please check you have all the parts listed below
2
Seat pad
(43.5 x 43 x 9cm)
3
1
Backrest
(37 x 68 x 10cm)
Leg frame
(41 x 55.5 x 41.5cm)
Components - Fittings
Please check you have all the fittings listed below
Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings
may be supplied than are required.
A
M8 x 20mm Bolt x 4 M6 x 20mm Bolt x 2 M6 x 12mm Bolt x 2
E
Spring Washer x 4
F
Big allen key x 1
Ruler - Use this ruler to help correctly identify the screws
CB
G
Small allen key x 1
D
Washer x 4
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100
105
110 115 120 125 130 135 140 145 150 155 160 165 170
2
Page 4
Assembly Instructions
Step 1
Attaching backrest
Position the backrest
on the seat frame as
shown and fix through
holes using bolts
,spring washer &
washers .
D
E
Tighten bolts using big
allen key .
F
1
3
A
D
1
D
E
A
E
A
1
D
E
A
A
E
A
E
D
D
E
A
3
3
D
Step 2
Attaching the seat
Place the seat pad
face down on a flat and
raised surface.
Position the assembled
chair frame upside down
on the seat pad as
shown and fix through
holes on the leg frame
and seat pad using
B
bolts and .
C
Tighten bolts using small
allen key .
G
2
2
C
3
3
2
C
3
C
B
2
B
B
3
2
Assembly is complete.
If you need help or have damaged or missing parts, call the Customer Helpline:
Argos = 0345 640 0800
3
Loading...