Hygena 457-1449D Instruction manual

Hygena Genoa Slatted TV Unit

Assembly Instructions - Please keep for future reference 457/1449D

Dimensions

Width - 110cm

Depth - 40cm

Height - 61cm

Important – Please read these instructions fully before starting assembly

If you need help or have damaged or missing parts, call the Customer Helpline: 03456 400800

Issue 1 - 16/09/15

Safety and Care Advice

Important – Please read these instructions fully before starting assembly

• Check you have all the
components and tools listed on
pages 2 & 3.

• Remove all fittings from the

plastic bags and separate them
into their groups.

• Keep children and animals
away from the work area, small
parts could choke if swallowed.

• Make sure you have enough
space to layout the parts before
starting.

Care and maintenance

• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.

• Do not stand or put weight on
the product, this could cause
damage.

• Assemble the item as close
to its final position (in the same
room) as possible.

• Assemble on a soft level
surface to avoid damaging the
unit or your floor.

• Parts of the assembly will be
easier with 2 people.

• From time to time check that
there are no loose screws on
this unit.

• We do not
recommend the
use of power
drill/drivers for

inserting screws,
as this could damage the unit.
Only use hand screwdrivers.

• Dispose of all packaging
carefully and responsibly.

• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.

Note: if require the next
page can be cut out and used
as reference throughout the
assembly. Keep this page with
these instructions for future
reference.

1

Components - Panels

Please check you have all the panels listed below

Bottom panel

1

(1100 x 400 mm)

Left side panel

4

(444 x 399mm)

Legs x 5

2

(60 x 60 mm) (1100 x 400mm)

Right side panel

5

(444 x 399mm) (444 x 355mm)

3

6

Top panel

Divider

Rear panel

7

(1086 x 468mm)

Adjustable shelf x 4

8

(523 x 350mm) (540 x 438mm)

Door

9

2

If you have damaged or missing components,

50mm Screw

x

A

G

I

40mm Screw

x

110 115 120 125 130 135 140 145 150 155 160 165 170

105

Metal dowel

x

6

D

Shelf pin

x

16

Components - Fittings

call the Customer Helpline: 03456 400800

Please check you have all the fittings listed below

Note: The quantities below are the correct amount to complete the assembly. In some cases more
fittings may be supplied than are required.

B C

Large wood dowel x 10

Metal cam x 6

Cover pad x 6

Tools required

E

H

Phillips screwdriver
(medium & small)

Flatblade screwdriver

5

F

14 mm Screw x 18

6

Small wood dowel x 12

Ruler - Use this ruler to help correctly identify the screws

0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100

3

Assembly Instructions

Step

Step

1

Lay Bottom Panel on
its long taped edge on a
flat soft surface.

Push Large wood dowels

A

into indicated holes in
Bottom panel.

Push Legs onto the

2

wood dowels in Bottom
panels and fasten using
50mm Screws .

1

B

2

A

B

Untaped edge.

1

2

4

Lay Side Panels
and Divider on their

6

taped edges on a flat
soft surface.

Push Small wood dowels

I

into ends of side
panels and .

5

4

Push Bottom panel
onto the wood dowels in
the end of panels and
fasten using 40mm
Screws .

H

5

6

1

Untaped edge.

Untaped edge.

I

H

1

5

Untaped edge.

Untaped edge.

6

4

4

Assembly Instructions

Step

Step

C

C

C

Step

3

Screw 6 Metal dowels
into the threaded holes in
Top Panel as

3

shown.

4

Panel onto the ends

f Side panels and

Insert Small wood dowels

I

into the middle holes in
dowels and wood

Side panels and Divider.
dowels enter

corresponding holes.

Firmly push the Top
Panel onto the ends
of the panels and

6

3

4

A

3

4 5

, ensuring the Metal
dowels and wood
dowels enter

I

corresponding holes.

C

3

Untaped edge.

5

6

5

Insert the 6 Metal Cams

D

into the 6 holes on
the Panels so
that they are flush.

Note: Longer
leg of the cross

on the Metal
Cams must face towards
end of panel (as shown).

Then, using a Philips
Screwdriver, screw all 6
Metal Cams

D

clockwise until they are

‘hand tight’.

654

4

3

Note: Longer leg of
the cross on the
Metal Cams must
face towards end

D

of panel.

Turn the unit upright.

5

Step

Step

Assembly Instructions

6

Secure the Rear Panel

7

into the rear edges
of side panels, top panel
and bottom panel
using 14mm Screws .

Note - make sure
cabinet is square
before securing

rear panel in place.

Measure on the back
across the 2 diagonals
to make sure cabinet is
square.

F

F

7

X

Y

7

Push 4 Shelf Pins

into each side of the

side panels and divider
at desired height.

Place adjustable
shelves onto the

8

Shelf Pins.

E

E

8

Taped edge.

6

Step

Assembly Instructions

8

Make sure the pin in the
top lock in the Door
is down, if not, push it
down until it locks.

Insert the bottom rollers
of Door in the groove
in the bottom panel,
holding the door and
push the top edge to line
up with the groove in top
panel as shown.

Push the release button
to release the pin into the
top groove.

Cover all visible cam
holes with Cover pad .

9

9

G

Pin 2 people needed for this step.

Release button

9

Assembly is complete.

If you need help or have damaged or missing parts, call the Customer Help Line: 03456 400800
Home Retail Group plc. Avebury, 489-499 Avebury Boulevard. Milton Keynes. MK9 2NW

7