Hygena 417-8976 Instruction manual

MADE IN

BRITAIN

Dimensions

Width - 99.5cm

Depth - 39.5cm

Height - 71.5cm

Berkeley - 4+1 Sideboard

Assembly Instructions - Please keep for future reference

If you need help or have damaged or missing parts, call the Customer Helpline: 03456 400800

Issue 1 - 11/05/15

Important - Please read these instructions fully before starting assembly

417/8976

hygena

Safety and Care Advice

Important - Please read these instructions fully before starting assembly

• Warning: This unit weighs approximately 31kgs. Please lift with care.

• Check you have all the components and tools listed on pages 1, 2 and 3.

• Remove all fittings from the plastic bags and separate them into their groups.

• Keep children and animals away from the work area, small parts could choke if swallowed.

• Parts of the assembly will be easier with 2 people.

• Make sure you have enough space to layout the parts before starting.

• Do not stand or put weight on the product, this could cause damage.

• Assemble the item as close to its final position (in the same room) as possible.

• Assemble on a soft level surface to avoid damaging the unit or your floor (use opened out unit carton).

Care and maintenance

• Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners.

• From time to time check that there are no loose screws on this unit.

• This product should not be discarded with household waste. Take to your local authority waste disposal centre.

Note: If required the next page can be cut out and used as reference throughout the assembly. Keep this page with these instructions for future reference.

• We do not recommend the use of power drill/drivers for

inserting screws, as this could damage the unit. Only use hand screwdrivers.

• Safety note: It is recommended that this unit is secured to a wall using the overbalance protector kit supplied or, an alternative fixing method of your choice.

• Dispose of all packaging carefully and responsibly.

Tools required

Rule Scissors Hammer

Eye protection (when using a hammer or drill)

Cross-head screwdriver

Electric drill (do not use for fitting screws)

Components - Panels

Please check you have all the panels listed below

2 3

If you have damaged or missing components, call the

Customer Helpline: 03456 400800 quoting the reference

numbers below

Left End (DF2882)

(563 x 392mm)

Top (DF2880)

(995 x 394mm)

Shelf (DF2886)

(447 x 373mm)

Right End (DF2883)

(563 x 392mm)

Divider (DF2884)

(563 x 392mm)

Base (DF2881)

(995 x 394mm)

Drawer Front (DF2885)

(495 x 137mm) x 4

Drawer Back (W447-95)

(447 x 95mm) x 4

Left Drawer Side (W350-95LH)

(350 x 95mm) x 4

Drawer Base (T458-347)

(458 x 347mm) x 4

Back (X987 x 589)

(987 x 589mm)

Right Drawer Side (W350-95RH)

(350 x 95mm) x 4

7 9

108

Door (DF2887)

(557 x 457mm)

Please check you have all the fittings listed below

Components - Fittings

If you have damaged or missing components, call the

Customer Helpline: 03456 400800 quoting the reference

numbers below

Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.

Ruler - Use this ruler to help correctly identify the screws

mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170

A B

D E F

G H I

M N

Metal dowel (F901) x 14

Wooden dowel (F22) x 12

Small locking nut (F3) x 8

Large locking nut (F900) x 6

40mm Screw (F910) x 6

R Runner (F160) x 4

L Runner (F161) x 4

L Runner (F159) x 4

R Runner (F162) x 4

350mm long

13mm Screw (F52) x 24 13mm Screw (F63) x 28

Knock-in Peg (F171GY) x 16

Wedgefix (F639) x 8

13mm Screw (F79) x 16

Strap

Screw Washer x 2

Overbalance protector kit (F269) x 1

P Q

Hinge (F518) x 2

Hinge plate (F523) x 2

Nail (F51) x 22

Leg Bracket

(F333) x 4

Handle (F415WAL) x 1

Leg (F343) x 4

Shelf stud (F110) x 4

25mm Screw (F50) x 1

Assembly Instructions

If you have damaged or missing components, call the

Customer Helpline: 03456 400800 quoting the reference

numbers below

Step 1

x 4

x 4 x 4

Step 2

Prepare the 4 drawer fronts

Screw 2 metal dowels into each of the 4 drawer fronts .

Note: Tighten the metal dowels up fully against the panels.

Prepare the drawer sides

Insert a small locking nut into the hole shown on the left drawer side and the right drawer side .

Note: The arrow on the locking nut must point towards the hole in the edge of the panel.

Step 3

Attach the drawer sides to the drawer fronts

Push the left drawer sides . and right drawer sides . onto the back of the drawer fronts .

Turn the small locking nuts on the left drawer side and right drawer side .

Note: Turn the locking nuts clockwise to secure panels - more than 1/2 a turn.

Assembly Instructions

Step 4

Fit the drawer base

Slide the drawer base down the grooves in the drawer sides and and down into the groove in the drawer front .

Step 5

Fit the drawer back

Fit the drawer back between the drawer sides and . Make sure that the drawer base fits into the groove in the drawer back .

Hold the drawer back in position and tap the knock-in pegs through the holes in the drawer sides and .

9 10

Step 6

Fit the wedgefixes

Turn the drawer assemblies over and slide 2 wedgefixes into the front and back grooves, as shown, and tighten up the screws.

x 4

+ 14 hidden pages