Hygena 158-9544, 146-4195, 413-9953 Instruction manual

MADE IN
BRITAIN
Dimensions
Width - 120cm
Depth - 49.5cm
Height - 43.5cm
Aurora - TV Unit
If you need help or have damaged or missing parts, call the Customer Helpline: 03456 400800
Issue 4 - 26/05/15
Important - Please read these instructions fully before starting assembly
158/9544
146/4195
413/9953
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
Warning: This unit weighs approximately 33kgs. Please lift with care.
• Check you have all the components and tools listed on pages 2 and 3.
• Remove all fittings from the plastic bags and separate them into their groups.
• Keep children and animals away from the work area, small parts could choke if swallowed.
• Parts of the assembly will be easier with 2 people.
• Make sure you have enough space to layout the parts before starting.
• Do not stand or put weight on the product, this could cause damage.
• Assemble the item as close to its final position (in the same room) as possible.
• Assemble on a soft level surface to avoid damaging the unit or your floor (use opened out unit carton).
• We do not recommend the use of power drill/drivers for
inserting screws, as this could damage the unit. Only use hand screwdrivers.
Safety note: If there is any chance of this unit being pulled over by children etc. it is recommended that the unit is secured to a wall using suitable fixings (not supplied).
• Dispose of all packaging carefully and responsibly.
1
Care and maintenance
• Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners.
• From time to time check that there are no loose screws on this unit.
• This product should not be discarded with household waste. Take to your local authority waste disposal centre.
Note: If required the next page can be cut out and used as reference throughout the assembly. Keep this page with these instructions for future reference.
Components - Panels
Please check you have all the panels listed below
2
1
2 3
If you have damaged or missing components, call the
Customer Helpline: 03456 400800 quoting the reference
numbers below
Top (D2637A)
(1200 x 495mm)
Left Side (D2645A)
(420 x 459mm)
4
6
Right Side (D2646A)
(420 x 459mm)
Horizontal (D2647A)
(572.5 x 455mm) x 2
Divider (D2648A)
(385 x 456mm)
Back (D2649A)
(1186 x 290mm)
5
8
7
Rail (D2651A)
(1160 x 95mm) x 2
Drawer Front (D2650A)
(1186 x 290mm)
Drawer Base (T532-347)
(532 x 347mm) x 2
Left Drawer Side (W350-165LH)
(350 x 165mm) x 2
Right Drawer Side (W350-165RH)
(350 x 165mm) x 2
Drawer Back (W521-165)
(521 x 165mm) x 2
9
10
11
12
Please check you have all the fittings listed below
3
Components - Fittings
If you have damaged or missing components, call the
Customer Helpline: 03456 400800 quoting the reference
numbers below
Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.
A
Wooden dowel (F22) x 9
B
Metal dowel (F901) x 18
C
D E
Large locking nut (F900) x 18
F
O
G H I
M
Small locking nut (F3) x 4
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
J K
9mm Screw (F73) x 12
Door Plate (F259) x 1
13mm Screw (F52) x 2
13mm Screw (F63) x 12
L
Door Push (F258) x 1
Feet (F854) x 2
Knock-in Peg (F171) x 8
P
R Runner (F160) x 2
b
L Runner (F161) x 2
P
c
L Runner (F159) x 2
P
a
R Runner (F162) x 2
P
d
350mm long
Double metal dowel (F566) x 2
Large wooden dowel (F40) x 1
N
Mini block (F25) x 4
Q
Wedgefix (F639) x 8
55mm Screw (F898) x 2
Assembly Instructions
4
If you have damaged or missing components, call the
Customer Helpline: 03456 400800 quoting the reference
numbers below
Step 1
Step 2
Fit the drawer sides to the drawer back
Make sure that the grooves on the inside of the drawer assembly line up.
a: With the drawer back
. in an upright position tap 2 knock-in pegs through the holes in the left drawer side .
Turn the assembly over
b: Hold the drawer back
. in position and tap 2 knock-in pegs through the holes in the right drawer side .
Step 3
Fit the drawer base
Slide the drawer base down the grooves in the drawer sides and and down into the groove in the drawer back .
b:a:
Turn the
assembly over
Prepare the 4 drawer sides
Insert a small locking nut into the hole shown on each of the 2 left drawer sides and 2 right drawer sides .
Note: The arrow on the locking nut must point towards the hole in the edge of the panel.
C
8
9
C
x 2
x 2 x 2
x 2 x 2
11
M
8
11
M
9
12
8 9
11
C
C
M
M
M
M
8
9
9
8
11
11
12
8
9
11
Assembly Instructions
5
Step 4
Fit the drawer front
Lower the 2 drawer assemblies down onto the back of the drawer front .
Use a screwdriver to tighten the 4 small locking nuts fitted to the drawer sides.
Note: Turn the small locking nuts as far as they will go - more than 1/2 a turn.
Step 5
B
Prepare the drawer front
Screw 4 metal dowels into the drawer front .
Note: Tighten the metal dowels up fully against the panels.
B
10
C
B
10
C
C
B
B
B
B
10
10
10
Step 6
Fit the wedgefixes
Turn the drawer assembly over.
Slide the wedgefixes into the small groove in the drawer front and the drawer backs , as shown.
Once in place, tighten up the screws.
Q
10
11
Q
Q
Q
Q
Q
Q
Q
Q
Q
11
11
Loading...
+ 14 hidden pages