Page 1
MADE IN
BRITAIN
Dimensions
Atlas - Slip Corner Robe
Assembly Instructions - Please keep for future reference
If you need help or have damaged or missing parts, call the Customer Helpline: 03456 400800
Issue 2 - 23/01/15
Important - Please read these instructions fully before starting assembly
327/9216
323/5748
331/6052
IMPORTANT
DO NOT follow the instructions
packed with the Door Pack.
Only use these instructions.
IMPORTANT
This unit MUST be fixed to a wall
using both of the brackets supplied.
Width - 100cm
Depth - 59.5cm
Height - 212.5cm
Page 2
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: This unit weighs
approximately 63kgs.
Please lift with care.
• Check you have all the
components and tools listed on
pages 1, 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
1
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: It is
recommended that this unit is
secured to a wall using the
brackets supplied.
• Dispose of all packaging
carefully and responsibly.
Tools required
Rule
Scissors
Spirit
level
Hammer Bradawl
Eye protection
(when using a
hammer or drill)
Cross-head
screwdriver
Step
ladder
Electric drill
(only use
when drilling
into walls)
Square
mm
10
20
30
40
50
60
70
80
90
100
mm
10
20
30
40
50
60
70
80
90
100
Page 3
Components - Panels
Please check you have all the panels listed below
2
If you have damaged or missing components, call the
Customer Helpline: 03456 400800 quoting the reference
numbers below
1
Universal End (D2396A)
(2074 x 591mm) x 2
2
3
Hanging Rail (FHR960)
(960mm long) x 2
4
Top/Base (D2395A)
(1000 x 592mm) x 2
Fixed Shelf (D2397A)
(968 x 590mm)
6 7
Back (X2100-994)
(2100 x 994mm)
Door Blanking Panel (DF548A)
(2100 x 495mm)
Door Spacer Panel (DF549A)
(2100 x 141mm)
5
Door (D2398A)
(2100 x 495mm)
The door is
not packed
with this unit.
It is sold
separately as
a door pack.
Page 4
Please check you have all the fittings listed below
3
Components - Fittings
If you have damaged or missing components, call the
Customer Helpline: 03456 400800 quoting the reference
numbers below
Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.
A
Wooden dowel (F22) x 2
B
Metal dowel (F901) x 4
C
D E
Large locking
nut (F900) x 4
F
G H I
L
O
Nail (F51) x 40
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
J
M
K
N
RQ
Allen Key (F36) x 1
50mm Screw (F49) x 12
19mm Screw (F461) x 2
25mm Screw (F50) x 6
13mm Screw (F63) x 24 13mm Screw (F79) x 3
Rail Holder
(F891) x 4
Bracket (F327) x 3
32mm Screw (F72) x 6
13mm Screw (F52) x 1
P
S
Handle (F323) x 1
Pre-mounted
hinge (F328) x 4
Hinge plate (F234) x 4
Hinge (F235) x 4
Feet (F854) x 6
Page 5
Assembly Instructions
4
If you have damaged or missing components, call the
Customer Helpline: 03456 400800 quoting the reference
numbers below
Step 1
Finished
front edge
Prepare the left end
Refer to step 1 and, if
you have chosen to fit 1
hanging rail, screw 2
metal dowels into the
left end .
Note: Tighten the metal
dowels up fully against
the panels.
To fit the rail holder ,
screw through its top
hole with screw and
into the shallow mark
hole drilled in the left end
. . Make sure that it is
fitted straight, in line with
the panel edges and
then fit another screw
using the lower hole.
Are you fitting 1 or 2
hanging rails or, a
shelf pack?
Step 2
If you are just
fitting 1 hanging
rail, the fixed
shelf will need
to go here.
Follow Steps 2
and 3.
Only follow Steps 2 and 3 if you are just fitting 1 hanging rail.
If you are fitting 2 hanging rails, follow Step 4 and 5.
If you are fitting 2
hanging rails, the
fixed shelf will
need to go here.
Follow Step 4
and 5.
J
M
J
M
B
M
J
B
B
1
1
B
M
1
J
Page 6
Assembly Instructions
5
Step 3
Only follow Steps 2 and 3 if you are just fitting 1 hanging rail.
If you are fitting 2 hanging rails, follow Step 4 and 5.
Step 4
Prepare the right end
Refer to step 1 and, if
you have chosen to fit 1
hanging rail, screw 2
metal dowels into the
right end .
Note: Tighten the metal
dowels up fully against
the panels.
To fit the rail holder ,
screw through its top
hole with screw and
into the shallow mark
hole drilled in the right
end . Make sure that
it is fitted straight, in line
with the panel edges and
then fit another screw
using the lower hole.
B
M
J
J
1
1
B
B
M
1
Finished
front edge
Finished
front edge
Prepare the left end
Refer to step 1 and, if
you have chosen to fit 2
hanging rails, screw 2
metal dowels into the
left end .
Note: Tighten the metal
dowels up fully against
the panels.
To fit the 2 rail holders
screw through the top
hole with screw and
into the shallow mark
hole drilled in the left end
. . Make sure that they
are fitted straight, in line
with the panel edges and
then fit another screw
using the lower hole.
B
M
J
J
B
B
1
1
J
M
J
M
B
M
1
M
Only follow Steps 4 and 5 if you are fitting 2 hanging rails.
If you are just fitting 1 rail, follow Step 2 and 3.
J
M
J
M
Page 7
A
Assembly Instructions
6
Step 5
Only follow Steps 4 and 5 if you are fitting 2 hanging rails.
If you are just fitting 1 rail, follow Step 2 and 3.
B
B
M
1
Finished
front edge
Prepare the right end
Refer to step 1 and, if
you have chosen to fit 2
hanging rails, screw 2
metal dowels into the
right end .
Note: Tighten the metal
dowels up fully against
the panels.
To fit the 2 rail holders
screw through the top
hole with screw and
into the shallow mark
hole drilled in the right
end . Make sure that
they are fitted straight, in
line with the panel edges
and then fit another
screw using the lower
hole.
B
M
J
J
1
1
J
M
J
M
B
M
Step 6
Prepare the fixed shelf
Tap 2 wooden dowels
into the fixed shelf .
Note: Wooden dowels
must not stick out from
the edge by more than
10mm or they may
damage other panels.
Insert 4 large locking
nuts into the fixed
shelf .
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
A
C
3
3
C
10mm
A
C
C
A
C
C
3
Finished
front edge
Page 8
Finished
front edge
Finished
front edge
Assembly Instructions
7
Step 7
Step 8
Join the fixed shelf to
the right side
Push the fixed shelf
onto the right side .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the fixed shelf .
Note: Turn the large
locking nuts as far as
they will go - more than
1/2 a turn.
B
C
3
1
1
3
C
C
3
Fit the left side
Push the left side
onto the fixed shelf .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the fixed shelf .
1
3
C
3
Finished
front edge
1
3
If you have fitted the
2 metal dowels in this
position, the fixed
shelf will go here.
The following diagrams will show the fixed
shelf at the top end of the unit.
You may have fitted it in the middle of the unit.
Page 9
Finished
front edge
Finished
front edge
Assembly Instructions
8
Step 9
Step 10
Fit the base
Attach the base to
the ends using 6
screws and tighten
them using the allen key
. .
Prepare the base
Screw the 6 feet into
the shallow mark holes
on the base using
screws .
O
2
H
2
1
F
E
H
O
O
O
O
O
O
Finished
front edge
E
F
F
F
F
F
F
2
1
1
2
G
H
25mm Screw
32mm Screw
Page 10
y
Assembly Instructions
9
Step 11
Step 12
F
F
F
2
E
F
F
F
Finished
front edge
1
1
Fit the top
Attach the top to the
ends using 6 screws
and tighten them using
the allen key .
2
1
F
E
2
Fit the back
a: Square up the unit by
making sure that
measurement x to x
equals y to y.
b: Place the back
onto the unit.
Nail around the
outside edges of
the back .
Note: Nails should
be spaced about
150mm apart.
Stand the unit up
for the next step.
7
D
The measurement from top corner X to bottom corner X must be
equal to the measurement from top corner Y to bottom corner Y
a:
7
Warning: The
unit is heavy.
Lift with care.
y
y
x
b:
D
7
Unit colour on
the top surface
x
Page 11
Assembly Instructions
10
Step 13
4
M
Fit the hanging rail(s)
Push the hanging rail(s)
. into the rail holders
fitted to the side panels.
4
M
4
Slip Corner Robe
Door on
the left
Door on
the right
Door Blanking
Panel on the
right
Door Blanking
Panel on the
left
Step 14
Choose which side to
fit the door and the
door blanking panel
Other Robe Other Robe
Slip Corner Robe
Page 12
Assembly Instructions
11
Step 15
Fit the door spacer
panel to the door
blanking panel
Attach the door spacer
panel to the door
blanking panel using
screws .
G
G
G
G
G
G
G
Finished
front edge
6
5
The large holes door on
the door blanking panel
must be at the bottom
of this surface
6
5
Step 16
90
J
J
P
J
J
P
J
J
P
J
J
P
P
Add the pre-mounted
hinges to the door
blanking panel
Push fit the pre-mounted
hinges into the door
blanking panel .
Secure each hinge with
2 screws .
Note: Before securing
with the screws, make
sure that the hinges are
positioned at 90 degrees
with the edge of the
door.
J
P
5
5
Page 13
Assembly Instructions
12
Step 17
Fit the door blanking
panel
2 people are needed
here
Note: Refer back to
Step 14 to choose which
side to fit the door
blanking panel.
Line up the 2 screws in
the top pre-mounted
hinge on the door
blanking panel with
the 2 holes at the top of
the end panel and
push them in.
Working down the door
blanking panel, push in
the other pre-mounted
hinges.
When all the pre-mounted
hinges have been
pushed into place,
tighten their 2 screws.
This shows the door blanking panel being
fitted onto the right side of the robe.
You may wish to fit it to the left side.
P
1
5
1
1
Press the screws into
the holes in the panels
When the hinges have
been pushed in,
tighten up their screws
P P
Warning: The
door blanking
panel is heavy.
Lift with care.
5
Note: Fit the
top hinge 1st
Page 14
Assembly Instructions
13
Step 18
Attach a bracket to
the fixed shelf
Fix a bracket into the
front hole underneath the
fixed shelf using
screw .
Use the right hand hole if
you have fitted the door
blanking panel on the
right side or, the left
hand hole if you have
fitted the door blanking
panel on the left side.
N
L
N
L
Step 19
Fix the door blanking
unit
Close the door blanking
panel and hold it against
the unit while it is being
fixed to the bracket.
Fix the back of the door
blanking panel to the
bracket using screw
. .
3
5
N
K
N
K
5
3
Page 15
Assembly Instructions
14
Step 20
Prepare the door from
the door pack
Push fit 4 hinges into
the door.
Secure each hinge with
2 screws .
Note: Before securing
with the screws, make
sure that the hinges are
positioned at 90 degrees
with the edge of the
door.
Door
J
R
90
R
J
J
R
J
J
R
J
J
R
J
J
R
IMPORTANT
DO NOT follow the instructions
packed with the Door.
Only use these instructions.
Page 16
Assembly Instructions
15
Step 21
Small piece of
waste wood
IMPORTANT
This step shows which handle holes to drill for a
LEFT HAND DOOR, as shown below.
Go to Step 22 if you need to drill a
RIGHT HAND DOOR.
For a left hand door,
drill these 2 handle
holes
Important: Please follow
these instructions
carefully.
Lay the door down onto
a smooth surface.
Check that the hinges
and holes are in the
same place as the
diagram.
Note: We recommend
the use of a small piece
of waste wood, placed
behind the holes while
drilling, to reduce the
possibility of any
breakout.
Using the pilot holes in
the rear face of the door,
drill through the 2 holes
indicated opposite, using
a 2.5mm diameter drill.
Turn the door over and
open out the 2.5mm
holes that you have just
drilled by drilling back
through them with a
5mm drill.
ONLY drill these 2 holes
Small piece of
waste wood
Door
Door
Page 17
Assembly Instructions
16
Step 22
Small piece of
waste wood
IMPORTANT
This step shows which handle holes to drill for a
RIGHT HAND DOOR, as shown below.
Go to back to Step 21 if you need to drill a
LEFT HAND DOOR.
For a right hand door,
drill these 2 handle
holes
Important: Please follow
these instructions
carefully.
Lay the door down onto
a smooth surface.
Check that the hinges
and holes are in the
same place as the
diagram.
Note: We recommend
the use of a small piece
of waste wood, placed
behind the holes while
drilling, to reduce the
possibility of any
breakout.
Using the pilot holes in
the rear face of the door,
drill through the 2 holes
indicated opposite, using
a 2.5mm diameter drill.
Turn the door over and
open out the 2.5mm
holes that you have just
drilled by drilling back
through them with a
5mm drill.
ONLY drill these 2 holes
Small piece of
waste wood
Door
Door
Page 18
Assembly Instructions
17
Step 23
Fit the hinge plates
Line up the 2 screws in
each hinge plate with
the 2 holes in the end
panel and push them
in.
When they have all been
pushed into place,
tighten the 2 screws on
each hinge plate .
This shows the hinges for the door being
fitted onto the left side of the robe.
You may wish to fit the door on the right side.
Q
Q
Q
1
Press the screws into
the holes in the panels
When the hinges have
been pushed in,
tighten up their screws
Q
1
Q
Q
Q
Q
Page 19
Assembly Instructions
18
Step 24
Fit door and handle
Note: The easiest way to
attach the door is to fit
the top hinge first, then
align and fit the other
hinges.
a: Push the hinge
onto the front part of the
hinge plate .
The lug at the bottom of
screw B goes into the
slot in the hinge plate.
b: Keep the hinge
FLAT against the hinge
plate as you slide it
across as far as it will go.
Tighten screw A.
c: The hinge must be
flat against the hinge
plate prior to any
adjustment.
d: The hinge must
NOT be AT AN ANGLE
to the hinge plate
when assembled.
This would indicate that
the lug at the bottom of
screw B had not located
in the slot in the hinge
plate and the hinge
would not be secure.
Remove the hinge from
the hinge plate and then
re-assemble being
careful to follow
instructions a-c.
e: Attach a handle to
the door using 2 screws
. .
R
R
R
Q
Q
Q
R
Q
S
I
a: b:
c: d:
Q
Q
Q
Q Q
R
R
R
R
R
B
A
I
I
S
This shows the door being fitted
onto the left side of the robe.
You may have chosen to fit the
door on the right side.
Door
Warning: The
door is heavy.
Lift with care.
Page 20
Assembly Instructions
19
Step 25
Adjust the door if
needed
a: Before adjusting the
door, use a spirit level to
check the top (or base)
of the unit is level, frontto-back and side-to-side
in the 3 positions shown.
Use suitable packing
pieces (not supplied) to
make the unit level
BEFORE making any
adjustment to the hinges,
as shown.
b: Height adjustment.
Loosen screws A on
hinge plates and move
door up or down as
required.
Retighten screw A.
c: Forward and Back
adjustment.
Loosen screw B on hinge
plate and move door in
or out as required.
Retighten screw B.
d: Sideways
adjustment.
To move door ‘out’
loosen screw C inside
the hinge.
To move door ‘in’ tighten
screw C inside the hinge.
b:
c:
d:
a:
A
A
B
C
Page 21
Assembly Instructions
20
Step 26
Position your robes
Place the slip corner
robe in the required
position, approximately
1210mm from the
skirting board to the
outside edge.
Push the other robe up
against it so that the
front face of its door
panel aligns with the
front edge of the door
spacer panel on the slip
corner robe.
Slip Corner
Robe
Warning: The
units are heavy.
Lift with care.
1210mm (approx)
from skirting board
1210mm (approx)
from skirting board
Slip Corner
Robe
Spacer panel
Door
Door
Spacer panel
Page 22
Assembly Instructions
21
Step 27
Top of Unit
WALL
WALL
Back of Unit
Fit the 2 brackets
To prevent possible
overbalancing, we
recommend that this unit
is secured to a suitable
wall by use of the 2
brackets fitted to the
top of the unit.
Fixings are not supplied,
as they will need to suit
the wall type and the
length of screws will
depend on the distance
from the back of the unit
to the wall.
Fix the brackets
loosely onto the top of
the unit using screws
and mark the wall for the
wall fixing.
Swivel the brackets
away from the wall and
drill the holes in the wall
using a suitable drill bit
and fit your wall fixings.
Swivel the brackets
back and fix the brackets
to the wall, then tighten
the screws .
Note: Take care when
drilling the wall that you
do not drill into any
pipes, wires etc.
If in doubt, consult an
expert.
Warning: The
unit is heavy.
Lift with care.
N
N
K
N
N
K
N
N
K
N
N
IMPORTANT
This unit MUST be fixed to a wall
using both of the brackets supplied.
The unit must be level and square
before fitting the brackets.
Page 23
Assembly Instructions
22
If you need help or have damaged or missing parts, call the Customer Helpline: 03456 400800
and quote the reference numbers on the component pages.
Argos Ltd, 489-499 Avebury Boulevard, Central Milton Keynes, MK9 2NW
Step 28
Assembly is complete
Page 24
ALR3068
Loading...