Hygena 323-5748, 331-6052, 327-9216 Instruction manual

MADE IN

BRITAIN

Dimensions

Atlas - Slip Corner Robe

Assembly Instructions - Please keep for future reference

If you need help or have damaged or missing parts, call the Customer Helpline: 03456 400800

Issue 2 - 23/01/15

Important - Please read these instructions fully before starting assembly

327/9216

323/5748

331/6052

IMPORTANT

DO NOT follow the instructions

packed with the Door Pack. Only use these instructions.

IMPORTANT

This unit MUST be fixed to a wall

using both of the brackets supplied.

Width - 100cm

Depth - 59.5cm

Height - 212.5cm

Safety and Care Advice

Important - Please read these instructions fully before starting assembly

• Warning: This unit weighs approximately 63kgs. Please lift with care.

• Check you have all the components and tools listed on pages 1, 2 and 3.

• Remove all fittings from the plastic bags and separate them into their groups.

• Keep children and animals away from the work area, small parts could choke if swallowed.

• Parts of the assembly will be easier with 2 people.

• Make sure you have enough space to layout the parts before starting.

• Do not stand or put weight on the product, this could cause damage.

• Assemble the item as close to its final position (in the same room) as possible.

• Assemble on a soft level surface to avoid damaging the unit or your floor (use opened out unit carton).

Care and maintenance

• Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners.

• From time to time check that there are no loose screws on this unit.

• This product should not be discarded with household waste. Take to your local authority waste disposal centre.

Note: If required the next page can be cut out and used as reference throughout the assembly. Keep this page with these instructions for future reference.

• We do not recommend the use of power drill/drivers for

inserting screws, as this could damage the unit. Only use hand screwdrivers.

• Safety note: It is recommended that this unit is secured to a wall using the brackets supplied.

• Dispose of all packaging carefully and responsibly.

Tools required

Rule

Scissors

Spirit level

Hammer Bradawl

Eye protection (when using a hammer or drill)

Cross-head screwdriver

Step ladder

Electric drill (only use when drilling into walls)

Square

100

Components - Panels

Please check you have all the panels listed below

If you have damaged or missing components, call the

Customer Helpline: 03456 400800 quoting the reference

numbers below

Universal End (D2396A)

(2074 x 591mm) x 2

Hanging Rail (FHR960)

(960mm long) x 2

Top/Base (D2395A)

(1000 x 592mm) x 2

Fixed Shelf (D2397A)

(968 x 590mm)

6 7

Back (X2100-994)

(2100 x 994mm)

Door Blanking Panel (DF548A)

(2100 x 495mm)

Door Spacer Panel (DF549A)

(2100 x 141mm)

Door (D2398A)

(2100 x 495mm)

The door is not packed with this unit. It is sold separately as a door pack.

Please check you have all the fittings listed below

Components - Fittings

If you have damaged or missing components, call the

Customer Helpline: 03456 400800 quoting the reference

numbers below

Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.

Wooden dowel (F22) x 2

Metal dowel (F901) x 4

D E

Large locking nut (F900) x 4

G H I

Nail (F51) x 40

Ruler - Use this ruler to help correctly identify the screws

mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170

Allen Key (F36) x 1

50mm Screw (F49) x 12

19mm Screw (F461) x 2

25mm Screw (F50) x 6

13mm Screw (F63) x 24 13mm Screw (F79) x 3

Rail Holder (F891) x 4

Bracket (F327) x 3

32mm Screw (F72) x 6

13mm Screw (F52) x 1

Handle (F323) x 1

Pre-mounted hinge (F328) x 4

Hinge plate (F234) x 4

Hinge (F235) x 4

Feet (F854) x 6

Assembly Instructions

If you have damaged or missing components, call the

Customer Helpline: 03456 400800 quoting the reference

numbers below

Step 1

Finished

front edge

Prepare the left end

Refer to step 1 and, if you have chosen to fit 1 hanging rail, screw 2

metal dowels into the left end .

Note: Tighten the metal dowels up fully against the panels.

To fit the rail holder , screw through its top hole with screw and into the shallow mark hole drilled in the left end . . Make sure that it is fitted straight, in line with the panel edges and then fit another screw using the lower hole.

Are you fitting 1 or 2 hanging rails or, a shelf pack?

Step 2

If you are just

fitting 1 hanging

rail, the fixed

shelf will need

to go here.

Follow Steps 2

and 3.

Only follow Steps 2 and 3 if you are just fitting 1 hanging rail.

If you are fitting 2 hanging rails, follow Step 4 and 5.

If you are fitting 2 hanging rails, the

fixed shelf will

need to go here.

Follow Step 4

and 5.

Assembly Instructions

Step 3

Only follow Steps 2 and 3 if you are just fitting 1 hanging rail.

If you are fitting 2 hanging rails, follow Step 4 and 5.

Step 4

Prepare the right end

Refer to step 1 and, if you have chosen to fit 1 hanging rail, screw 2

metal dowels into the right end .

Note: Tighten the metal dowels up fully against the panels.

To fit the rail holder , screw through its top hole with screw and into the shallow mark hole drilled in the right end . Make sure that it is fitted straight, in line with the panel edges and then fit another screw using the lower hole.

Finished

front edge

Finished

front edge

Prepare the left end

Refer to step 1 and, if you have chosen to fit 2 hanging rails, screw 2

metal dowels into the left end .

Note: Tighten the metal dowels up fully against the panels.

To fit the 2 rail holders screw through the top hole with screw and into the shallow mark hole drilled in the left end . . Make sure that they are fitted straight, in line with the panel edges and then fit another screw using the lower hole.

Only follow Steps 4 and 5 if you are fitting 2 hanging rails.

If you are just fitting 1 rail, follow Step 2 and 3.

Assembly Instructions

Step 5

Only follow Steps 4 and 5 if you are fitting 2 hanging rails.

If you are just fitting 1 rail, follow Step 2 and 3.

Finished

front edge

Prepare the right end

Refer to step 1 and, if you have chosen to fit 2 hanging rails, screw 2

metal dowels into the right end .

Note: Tighten the metal dowels up fully against the panels.

To fit the 2 rail holders screw through the top hole with screw and into the shallow mark hole drilled in the right end . Make sure that they are fitted straight, in line with the panel edges and then fit another screw using the lower hole.

Step 6

Prepare the fixed shelf

Tap 2 wooden dowels into the fixed shelf .

Note: Wooden dowels must not stick out from the edge by more than 10mm or they may damage other panels.

Insert 4 large locking nuts into the fixed shelf .

Note: The arrow on the locking nut must point towards the hole in the edge of the panel.

10mm

Finished

front edge

Finished

front edge

Finished

front edge

Assembly Instructions

Step 7

Step 8

Join the fixed shelf to the right side

Push the fixed shelf onto the right side .

Use a screwdriver to tighten the 2 large locking nuts fitted to the fixed shelf .

Note: Turn the large locking nuts as far as they will go - more than 1/2 a turn.

Fit the left side

Push the left side onto the fixed shelf .

Use a screwdriver to tighten the 2 large locking nuts fitted to the fixed shelf .

Finished

front edge

If you have fitted the

2 metal dowels in this

position, the fixed

shelf will go here.

The following diagrams will show the fixed

shelf at the top end of the unit.

You may have fitted it in the middle of the unit.

+ 16 hidden pages