Hygena 259-3773, 274-8944 Instruction manual

MADE IN

BRITAIN

Dimensions

Width - 116.5cm

Depth - 49.5cm

Height - 183.5cm

Assembly Instructions - Please keep for future reference

If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800

Issue 4 - 25/04/14

Important - Please read these instructions fully before starting assembly

259/3773

274/8944

Camden - 2 Drawer 3 Door Mirror Robe

Safety and Care Advice

Important - Please read these instructions fully before starting assembly

• Warning: This unit weighs approximately 71kgs. Please lift with care.

• Check you have all the components and tools listed on pages 1, 2 and 3.

• Remove all fittings from the plastic bags and separate them into their groups.

• Keep children and animals away from the work area, small parts could choke if swallowed.

• Parts of the assembly will be easier with 2 people.

• Make sure you have enough space to layout the parts before starting.

• Do not stand or put weight on the product, this could cause damage.

• Assemble the item as close to its final position (in the same room) as possible.

• Assemble on a soft level surface to avoid damaging the unit or your floor (use opened out unit carton).

1

Care and maintenance

• Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners.

• From time to time check that there are no loose screws on this unit.

• This product should not be discarded with household waste. Take to your local authority waste disposal centre.

• We do not recommend the use of power drill/drivers for

inserting screws, as this could damage the unit. Only use hand screwdrivers.

• Safety note: It is recommended that this unit is secured to a wall using the bracket supplied.

• Dispose of all packaging carefully and responsibly.

Rule

Tools required

Rule

ScissorsSquare

Spirit level

Hammer Bradawl

Eye protection (when using a hammer or drill)

Cross-head screwdriver

Step ladder

Electric drill (only use when drilling into walls)

mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170

Ruler - Use this ruler to help correctly identify the screws

Components - Panels

Please check you have all the panels listed below

2

1 2

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

7 8

3

4 5

6

Hanging Rail (FHR343)

(343mm long)

9

Hanging Rail (FHR715)

(715mm long)

10

11

13

14

15

12

Mirror Door

(D2018MA)

(1345 x 358mm)

(Mirror - SG06 1344 x 358mm Safety Back SAR)

Left Side (D2019A)

(1800 x 491mm)

Right Side (D2015A)

(1800 x 491mm)

Small Back Rail (D2013A)

(349.5 x 130mm)

Large Back Rail (D2014A)

(725.5 x 130mm)

Plinth (D2012A)

(1090 x 96mm) x 2

Horizontal (D2010A)

(1090 x 473mm)

Plain Door (D2018A)

(1345 x 358mm) x 2

Top (D2009A)

(1166 x 492mm)

Upright (D2016A)

(1344 x 472mm)

Drawer Front (D2017A)

(1084 x 173mm) x 2

Drawer Base (T1050-357)

(1050 x 357mm) x 2

Drawer Back (W1039-124)

(1039 x 124mm) x 2

16

17

Left Drawer Side

(W350-124LH)

(350 x 124mm) x 2

Right Drawer Side

(W350-124RH)

(350 x 124mm) x 2

18

Small Back

(X1712-363)

(1712 x 363mm)

19

Large Back (X940)

(1712 x 740mm)

Please check you have all the fittings listed below

3

Components - Fittings

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.

B C

D E F

G H I

Nail (F51) x 38

L

Hinge plate (F523) x 9

Rail Holder (F891) x 4

13mm Screw (F63) x 38

Hollow core locking nut (F892) x 4

Small metal dowel (F893) x 4

Metal dowel (F901) x 16

Large locking nut (F900) x 14

A

Wooden dowel (F22) x 12

K

Bracket (F327) x 1

O

NM

Q

Small locking nut (F3) x 4

19mm Screw (F461) x 8

Knock-in Peg (F171) x 8

P

Double metal dowel (F566) x 1

13mm Screw (F52) x 12

S

b

S

c

S

a

S

d

J

13mm Screw (F79) x 1

R

Hinge (F522) x 9

T

40mm Screw (F910) x 2

Handle (F309) x 4

U

432mm

Wedgefix

(F639) x 8

W

X

Nail screw (F277) x 6 Back holder (F276) x 6

* These can also be round

R Runner (F160) x 1

L Runner (F161) x 1

L Runner (F159) x 1

R Runner (F162) x 1

350mm long

Assembly Instructions

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Step 1

4

G

Prepare the 2 drawer fronts

Screw 2 metal dowels into the holes shown on the back of each drawer front .

Note: Tighten metal dowels up fully against the panels.

G

11

Prepare drawer sides and drawer backs

Insert a small locking nut into the hole shown on the left drawer side and right drawer side .

Note: The arrow on the locking nut must point towards the hole in the edge of the panel.

I

13

14

Step 2

x 2

Step 3

Attach the drawer sides to the drawer front

Push the left drawer side . and right drawer side . onto the back of the drawer front .

Turn the small locking nuts on the left drawer side and right drawer side .

Note: Turn the locking nuts clockwise to secure panels - more than 1/2 a turn.

13 14

11

I

13 14

I

B

G

I

Note: The locking nuts can be on either surface of the drawer sides. Make sure that the small groove is on the inside, as shown.

G

11

Groove

11

I

Note: Due to the manufacturing process, the holes for the locking nut can be on either surface of the drawer sides.

x 2 x 2

I

13

14

13

14

11

Assembly Instructions

5

Step 4

Step 5

x 2

8

Fit the drawer base

Slide the drawer base down the grooves in the drawer sides and and down into the groove in the drawer front .

15

13 14

11

Attach the handles

Attach a handle to each drawer front using 2 screws .

U

O

Step 6

11

x 2

Fit the drawer back

Fit the drawer back between the drawer sides and .

Make sure that the drawer base fits into the groove in the drawer back .

Hold the drawer back in position and tap the knock-in pegs through the holes in the drawer sides and .

12

13 14

15

12

M

13 14

15

11

x 2

8

15

13

14

M

13

M

12

U

O

11

Assembly Instructions

6

Step 7

Step 8

x 2

Fit the runners to the drawers

Fit the runner to the bottom edge of the left drawer side , as shown, making sure that it is pushed up against the back of the drawer front . Use a bradawl to mark the fixing positions, then secure with 2 screws .

Fit the runner to the bottom edge of the right drawer side using the same method.

14

S c

13

11

F

S d

Fit the wedgefixes

Turn the 2 drawer assemblies over and slide 4 wedgefixes into the front and back grooves, as shown, and tighten up the screws.

T

x 2

F

Runners must be

pushed up against

the drawer front

S d

R

14

13

11

L

S c

L

Finished

front edge

Assembly Instructions

7

Step 9

Prepare the upright

a: Tap 2 wooden

dowels into the ends of the upright .

Note: Wooden dowels must not stick out from the edge by more than 10mm or they may damage other panels.

To fit the rail holder , screw through the top hole with screw and into the mark hole drilled in the upright . Make sure that it is fitted straight, in line with the panel edges and then fit another screw using the lower hole.

Turn upright panel over

E

F

b:

a:

4

Turn the upright over

L

10mm

A

4

L

b: Fit 3 hinge plates

onto the upright , making sure that the slot is facing towards the finished front edge.

To fit the rail holder , screw through the top hole with screw and into the mark hole drilled in the upright . Make sure that it is fitted straight, in line with the panel edges and then fit another screw using the lower hole.

Insert 2 large locking nuts into the upright.

Note: The arrow on the locking nut must point towards the hole in the edge of the panel.

4

E

F

4

H

F

E

F

E

H

A

F

E

4

H

F

E

4

L

Finished

front edge