Hygena 248-4277, 268-8860 Instruction manual

MADE IN

BRITAIN

Dimensions

Width - 49cm

Depth - 39cm

Height - 43cm

Camden - Bedside

Assembly Instructions - Please keep for future reference

If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800

Issue 4 - 10/04/14

Important - Please read these instructions fully before starting assembly

248/4277

268/8860

Safety and Care Advice

Important - Please read these instructions fully before starting assembly

• Warning: This unit weighs approximately 11kgs. Please lift with care.

• Check you have all the components and tools listed on pages 2 and 3.

• Remove all fittings from the plastic bags and separate them into their groups.

• Keep children and animals away from the work area, small parts could choke if swallowed.

• Make sure you have enough space to layout the parts before starting.

• Do not stand or put weight on the product, this could cause damage.

• Assemble the item as close to its final position (in the same room) as possible.

• Assemble on a soft level surface to avoid damaging the unit or your floor (use opened out unit carton).

• We do not recommend the use of power drill/drivers for

inserting screws, as this could damage the unit. Only use hand screwdrivers.

• Safety note: If there is any chance of this unit being pulled over by children etc. it is recommended that the unit is secured to a wall using suitable fixings (not supplied).

• Dispose of all packaging carefully and responsibly.

Care and maintenance

• Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners.

• From time to time check that there are no loose screws on this unit.

• This product should not be discarded with household waste. Take to your local authority waste disposal centre.

Note: If required the next page can be cut out and used as reference throughout the assembly. Keep this page with these instructions for future reference.

Components - Panels

Please check you have all the panels listed below

1 2

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

7 8 9

Top (D1985A)

(489 x 391mm)

Left Side (D1986B)

(396 x 389mm)

Plinth (D1988A)

(413 x 96mm) x 2

Drawer Front (D1989A)

(410 x 173mm)

Horizontal (D1990A)

(413 x 367mm)

Drawer Base (T372-347)

(372 x 347mm)

Right Side (D1987B)

(396 x 389mm)

Drawer Back (W362-124)

(362 x 124mm)

Back (X432-350)

(432 x 350mm)

Left Drawer Side (W350-124LH)

(350 x 124mm)

Right Drawer Side (W350-124RH)

(350 x 124mm)

Please check you have all the fittings listed below

Components - Fittings

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.

Ruler - Use this ruler to help correctly identify the screws

mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170

Wooden dowel (F22) x 4

Metal dowel (F901) x 10

Large locking nut (F900) x 8

Small locking nut (F3) x 2

Small metal dowel (F893) x 4

19mm Screw (F461) x 2 Handle (F266) x 1

Nail (F51) x 11

J K

Hollow core locking nut (F892) x 4

Wedgefix (F639) x 4

Knock-in Peg (F171) x 4

13mm Screw (F63) x 6

13mm Screw (F52) x 6

R Runner (F160) x 1

L Runner (F161) x 1

L Runner (F159) x 1

R Runner (F162) x 1

304mm

Assembly Instructions

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Prepare the drawer front

Screw 2 metal dowels into the drawer front .

Note: Tighten the metal dowels up fully against the panels.

Prepare the drawer sides

Insert a small locking nut into the hole shown on the left drawer side and right drawer side .

Note: The arrow on the locking nut must point towards the hole in the edge of the panel.

Attach the drawer sides to the drawer front

Push the left drawer side . and right drawer side . onto the back of the drawer front .

Turn the small locking nuts on the left drawer side and right drawer side .

Note: Turn the locking nuts clockwise to secure panels - more than 1/2 a turn.

7 8

Small groove

Note: Due to the manufacturing process, the holes for the locking nut can be on either surface of the drawer sides.

Note: The locking nuts can be on either surface of the drawer sides. Make sure that the small groove is on the inside, as shown.

Step 2

Step 3

Step 1

+ 11 hidden pages