Hygena 264-9971 Instruction manual

MADE IN

BRITAIN

Dimensions

Width - 79.5cm

Depth - 49.5cm

Height - 183.5cm

Camden - 2 Door Robe

Assembly Instructions - Please keep for future reference

If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800

Issue 4 - 24/03/14

Important - Please read these instructions fully before starting assembly

266/1021

264/9971

Safety and Care Advice

Important - Please read these instructions fully before starting assembly

• Warning: This unit weighs approximately 45kgs. Please lift with care.

• Check you have all the components and tools listed on pages 2 and 3.

• Remove all fittings from the plastic bags and separate them into their groups.

• Keep children and animals away from the work area, small parts could choke if swallowed.

• Make sure you have enough space to layout the parts before starting.

• Do not stand or put weight on the product, this could cause damage.

• Assemble the item as close to its final position (in the same room) as possible.

• Assemble on a soft level surface to avoid damaging the unit or your floor (use opened out unit carton).

1

Care and maintenance

• Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners.

• From time to time check that there are no loose screws on this unit.

• This product should not be discarded with household waste. Take to your local authority waste disposal centre.

Note: If required the next page can be cut out and used as reference throughout the assembly. Keep this page with these instructions for future reference.

• We do not recommend the use of power drill/drivers for

inserting screws, as this could damage the unit. Only use hand screwdrivers.

• Safety note: It is recommended that this unit is secured to a wall using the bracket supplied.

• Dispose of all packaging carefully and responsibly.

Components - Panels

Please check you have all the panels listed below

2

1 2

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Base (D2006A)

(722 x 473mm)

Door (D2008A)

(1700 x 358mm) x 2

5

4

Plinth (D1994A)

(722 x 96mm)

6

3

Hanging Rail (FHR715)

(715mm long)

7

8

Back (X733)

(1713 X 740mm)

Left Side (D2004A)

(1800 x 491mm)

Top (D2003A)

(796 x 492mm)

Right Side (D2005A)

(1800 x 491mm)

Back Rail (D2007A)

(722 x 130mm)

9

Please check you have all the fittings listed below

3

Components - Fittings

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.

Rule

mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170

Tools required

Rule

ScissorsSquare

Spirit level

Hammer Bradawl

Eye protection (when using a hammer or drill)

Cross-head screwdriver

mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170

Step ladder

Ruler - Use this ruler to help correctly identify the screws

Electric drill (only use when drilling into walls)

B C

D E F

G H I

Nail (F51) x 32

M

L

Hinge plate (F523) x 6

Rail Holder (F891) x 2

13mm Screw (F63) x 16

Hollow core locking nut (F892) x 4

Small metal dowel

(F893) x 4

19mm Screw (F461) x 4

Metal dowel (F901) x 8

Large locking nut (F900) x 8

Hinge (F522) x 6

A

Wooden dowel (F22) x 6

N

Handle (F309) x 2

J K

Bracket (F327) x 1

13mm Screw (F79) x 1

Assembly Instructions

4

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Step 1

L

Prepare the left side

a: Fit 3 hinge plates

onto the left side , making sure that the slot is facing towards the finished front edge.

b: To fit the rail holder

. , screw through the top hole with screw and into the mark hole drilled in the left side . Make sure that it is fitted straight, in line with the panel edges and then fit another screw using the lower hole.

c: Push 2 hollow core

locking nuts into the left side , making sure that they are flush against the panel’s surface. Using a hammer, tap in the pin on the hollow core locking nut .

Note: The pin should be tapped in flush with the top surface of the hollow core locking nut .

d: Screw 4 metal

dowels into the holes on the left side .

Note: Tighten metal dowels up fully against the panel.

1

E

F

b:

B

G

a:

Finished

front edge

L

F

E

B

B B

B

1

G

c:

1

G

d:

F

E

F

E

G

Assembly Instructions

5

Step 2

F

B

L

2

L

Finished

front edge

L

2

E

F

B

G

a:

G

d:

b:

B

B B

c:

E

Prepare the right side

a: Fit 3 hinge plates

onto the right side , making sure that the slot is facing towards the finished front edge.

b: To fit the rail holder

. , screw through the top hole with screw and into the mark hole drilled in the right side . . Make sure that it is fitted straight, in line with the panel edges and then fit another screw using the lower hole.

c: Push 2 hollow core

locking nuts into the right side , making sure that they are flush against the panel’s surface. Using a hammer, tap in the pin on the hollow core locking nut .

Note: The pin should be tapped in flush with the top surface of the hollow core locking nut .

d: Screw 4 metal

dowels into the holes on the right side .

Note: Tighten metal dowels up fully against the panel.

2

F

E

F

E

G

Finished

front edge

Finished

front edge

Assembly Instructions

6

Step 3

Prepare the base

Insert 4 large locking nuts into the base .

Note: The arrow on the locking nut must point towards the hole in the edge of the panel.

Tap 2 wooden dowels into the base .

Note: Wooden dowels must not stick out from the edge by more than 10mm or they may damage other panels.

5

A

H

10mm

A

G

Fit the base to the right side

Push the base onto the right side .

Use a screwdriver to tighten the 2 large locking nuts fitted to the base .

Note: Turn the large locking nuts as far as they will go - more than 1/2 a turn.

Step 4

Step 5

5

2

5

H

5

2

H

5

C

4

Prepare the top

Screw 4 small metal dowels into the holes on the top .

Note: Tighten metal dowels up fully against the panel.

H

Assembly Instructions

Step 6

Prepare the plinth and the back rail

Insert 2 large locking nuts into the plinth and 2 into the back rail . .

Tap 2 wooden dowels into the plinth and 2 into the back rail .

A

H

6

9

A

H

9

C

B B

Fit the top

Attach the top onto the assembly.

Note: You will need to slide the 2 small metal dowels into the top of the 2 hollow core locking nuts .

Insert a screwdriver into the 2 hollow core locking nuts and turn the nuts inside as far as they will go.

4

C

B

2

4

Step 7

Assembly Instructions

8

Step 8

Step 9

1

5

6

C

B B

Fit the left side

Push the left side onto the assembly.

Note: You will need to slide the 2 small metal dowels into the top of the 2 hollow core locking nuts .

Insert a screwdriver into the 2 hollow core locking nuts and turn the nuts inside as far as they will go.

Use a screwdriver to tighten the 4 large locking nuts fitted to the base , plinth and back rail .

1

C

B

4

9

Fit the plinth and the back rail

Push the plinth and the back rail onto the right side .

Use a screwdriver to tighten the 2 large locking nuts fitted to the plinth and back rail .

Note: Support the end of the plinth and back rail until the left side has been fitted.

6

2

6

H

6

2

9

6

H

6

9

5

Assembly Instructions

Step 10

yyy

x

Warning: The robe is heavy. Lift with care.

9

Fit the back panel

a: Square up the unit by

making sure that measurement x to x

equals y to y.

b: Place the back

onto the unit, coloured surface facing down.

Note: The back must be positioned so that it is central on the unit.

Nail around the outside edges of the back .

Note: Nails should try to be spaced out evenly.

Stand the unit up for the next stage.

8

D

8

The measurement from top corner X to bottom corner X must be

equal to the measurement from top corner Y to bottom corner Y

a:

b:

D

x

8

Assembly Instructions

10

Step 11

90

M

3

M

F

Prepare the 2 doors

Push fit the 3 hinges into the door .

Secure each hinge with 2 screws .

Note: Before securing with the screws, make sure that the hinges are positioned at 90 degrees with the front edge of the door.

F

M

3

M

F

M

F

7

Fit the hanging rail

Push the hanging rail into the rail holders fitted to the side panels.

E

Step 12

3

7

E

7

Assembly Instructions

Step 13

Fit doors and handles

2 people are needed here

Note: The easiest way to

attach the door is to fit the top hinge first, then align and fit the other hinges.

a: Push the hinge

onto the front part of the hinge plate .

b: Keep the hinge

FLAT against the hinge plate as you slide it across as far as it will go. Tighten screw A.

c: The hinge must be

flat against the hinge plate prior to any adjustment.

d: The hinge must

NOT be AT AN ANGLE to the hinge plate when assembled. This would indicate that the recess at the bottom of screw B had not located in the slot in the hinge plate and the hinge would not be secure. Remove the hinge from the hinge plate and then re-assemble being careful to follow instructions a-c.

e: Attach a handle to

each door using 2 screws .

screw A

a: b:

c:

e:

d:

A

screw B

M

L

M

L

N

I

3

M

MM

L

3

11

I

3

N

Assembly Instructions

12

Step 14

b:

c:

d:

A

B

C

a:

Adjust doors if needed

a: Before adjusting the

doors, use a spirit level to check the top (or base) of the unit is level, front-to-back and sideto-side in the 3 positions shown. Use suitable packing pieces (not supplied) to make the unit level BEFORE making any adjustment to the hinges, as shown.

b: Height adjustment.

Loosen screws A on hinge plates and move door up or down as required. Retighten screw A.

c: Forward and Back

adjustment. Loosen screw B on hinge plate and move door in or out as required. Retighten screw B.

d: Sideways

adjustment. To move door ‘out’ loosen screw C. To move door ‘in’ tighten screw C

If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800

and quote the reference numbers on the component pages.

Argos Ltd, 489-499 Avebury Boulevard, Central Milton Keynes, MK9 2NW

Assembly Instructions

13

Step 15

WALL

Back of Unit

Attach bracket to top

To prevent possible overbalancing, we recommend that this unit is secured to a suitable wall by use of the bracket fitted to the top of the unit.

Fixings are not supplied, as they will need to suit the wall type and the length of screw will depend on the distance from the back of the unit to the wall.

Fit the bracket loosely onto the top of the unit, fixing screw between 10 and 15mm in from the back edge, and mark the wall for the wall fixing.

Swivel the bracket away from the wall and drill a hole in the wall using a suitable drill bit and fit your wall fixing.

Swivel the bracket back and fix the bracket to the wall, then tighten Screw .

Note: Take care when drilling the wall that you do not drill into any pipes, wires etc. If in doubt, consult an expert.

Warning: The robe is heavy. Lift with care.

Assembly is complete

K

J

K

J

K

J

K

10-15mm

Top of Unit