Hygena 259-5915 Instruction manual

Bergen 120 Mirror/mirror

Assembly Instructions- Please keep for future reference 259/5915

DR8250070

Dimensions

Width - 120cm

Depth - 59.5cm

Height - 199.8cm

Tip : To prevent damage,

we recommend that you

build your unit on the

carton(s) it was packed in.

Important – Please read these instructions fully before starting assembly

If you need help or have damaged or missing parts, please visit: www.argos-support.co.uk or email: Help@ClickSpares.co.uk (quoting your original order number) Alternatively, call the Spares Helpline on: 0370 112 1928 For any other queries please contact the Customer Helpline on: 0345 640 2020

Issue 3 - 05/11/15

Safety and Care Advice

Important – Please read these instructions fully before starting assembly

• Check you have all the components and tools listed on the following pages.

plastic bags and separate them into their groups.

• Keep children and animals away from the work area, small parts could choke if swallowed.

• Make sure you have enough space to layout the parts before starting.

Care and maintenance

• Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners.

• During assembly do not stand or put weight on the product, this could cause damage.

• Assemble the item as close

room) as possible.

• Assemble on a soft level surface to avoid damaging the

• Parts of the assembly will be easier with 2 people.

• From time to time check that there are no loose screws on this unit.

• To reduce the likelihood of damaging your product please

ensure that your power drill is set on a low torque setting.

• This product should not be discarded with household waste. Take to your local authority waste disposal centre.

Handy Hints

• Assemble all parts and bolts loosely during assembly, only once the product is complete should you fully tighten the bolts

Instruction video

• This manual is provided with an additional instruction video. If the icon on the right is displayed at a particular step in the manual, Follow the link: http://nlink.nu/vid02 Or scan the QR code on the left with your phone.

• Regularly check and ensure

tightend properly.

See page 2 for link to instruction video!

Note: if required the next page can be cut out and used as reference throughout the assembly. Keep this page with these instructions for future reference.

Components - Panels

For damaged or missing parts, please visit: www.argos-support.co.uk or email: Help@ClickSpares.co.uk

Please check you have all the panels listed below

Left side

(199.8 x 52.9cm)

P2883

Top

(117 x 51cm)

P1883

Plinth x2

(117 x 6cm)

P7883

Right side

(199.8 x 55.8cm)

P2882

Upright

(190.3 x 49cm)

P2886

Bottom

(117 x 51.1cm)

P1884

Shelf x2

(57.7 x 48.8cm)

P1886

Foldy back x2

(193 x 59cm)

BO3429

Door2x

(195.2 x 61.3cm)

PS3293

Components - Fittings

For damaged or missing parts, please visit: www.argos-support.co.uk or email: Help@ClickSpares.co.uk

Please check you have all the fittings listed below

Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.

1/2

FK1005

Confirmat screw x 4 (5x40mm)

FK1309

Screw x 4 (4x12.5mm)

FK1052

Double locking screw x 3 (5x66.5mm)

FK1248

Corner connector, white x 2

FK1235

L-Bracket x 1

PM1823

Locking screw x 24

(5x24mm)

Plug, Nylon x 16 (5x9mm)

Wood dowel x 4 (8x30mm)

Hanger rail support, gray x 4

Nail holder x 1

FK1011

Screw x 49 (4x15mm)

FK1082

Nail x 60

FK1411

Large locking nut x 18 (15x12mm)

FK1217

Peg, brown x 1

FK1419

Connecting plate x 0 (not used)

PM1613

FK1400

FK1515

FK1012

15mm

FK1234

FK1236

PK1613

Hanger rail x 2

(569mm)

Door handle x 3 (1952mm)

Allen key x 1 (3mm)

PM1652B

FK1013

Guide rail x 1, metal (1169mm)

Brush x 3 (1952mm)

PM1652C

ZF99936

Wall plug (6mm) and parkerscrew x 1

Guide rail x 1, plastic(1169mm)

Door trim x 1 (1952mm)

PM1652D

Components - Fittings

Please check you have all the fittings listed below

Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.

2/2

Screw x 2 (3.5x35mm)

Screw x 2 (4x14mm)

End stop x 2

Back guide part x 2

ZF9997I

ZF9997J

ZF9997G

ZF9998D

Screw x 6 (3.5x25mm)

Spacer x 1

Stop guide rail x 2

Sliding door connecting plate x 2

ZF9997K

ZF9997F

ZF9997H

ZF9997B

Screw x 33

(4x15mm)

ZF9997L

ZF9997E

Tapping block for guide rail x 2

ZF9997C

Front guide part x 2

ZF9997A

Sliding door connecting bracket x 2

Tools required

Phillips screwdriver

(medium & large)

Stairs

Drill

Flatblade screwdriver

(medium)

Piercer

(small)

Spirit level

5mm Suitable drill bit

Setsquare

Ruler - Use this ruler to help correctly identify the screws

105

0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100

110 115 120 125 130 135 140 145 150 155 160 165 170

0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150

0 1 2 3 4 5 6

Eye protection (when using a hammer or drill)

Small hammer

Ruler/tape measure

Scissors

Assembly Instructions

BBBBBBBBBBBBBBBBBBB

Step 1

Cabinet assembly

a: Screw 9 locking screws

into the holes on back

of the left side 1.

Mount hanger rail support K, fasten with 1 screw D. Screw D into the board between two predrilled holes. Mount tapping block for guide rail f with two screws b.

b: Screw 9 locking screws

B into the holes on back of the right side 2 .

Mount hanger rail support K, fasten with 1 screw D. Screw D into the board between two predrilled holes.

Mount tapping block for guide rail f with two screws b.

Finished front edge

C: Mount hanger rail

support K on the upright 3, fasten with screw D 1x. Screw D into the board between two predrilled holes

Turn over.

Mount hanger rail support K on the upright 3, fasten with screw D 1x. Screw D into the board between two predrilled holes.

Finished front edge

+ 14 hidden pages