Hygena 2594088 Instruction manual

MADE IN

BRITAIN

Dimensions

Width - 50cm

Depth - 59cm

Height - 87cm

Valencia - 500mm Base Cabinet

Assembly Instructions - Please keep for future reference

If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800

Issue 2 - 31/07/14

Important - Please read these instructions fully before starting assembly

hygena

656/5776

633/2882

633/2710

205/4009

633/2806

192/3722

Cabinet

Black Door Pack

Cream Door Pack

Oak Door Pack

White Gloss Door Pack

White HN Door Pack

Safety and Care Advice

Important - Please read these instructions fully before starting assembly

• Warning: This unit weighs approximately 16.5kgs. Please lift with care.

• Check you have all the components and tools listed on pages 1, 2 and 3.

• Remove all fittings from the plastic bags and separate them into their groups.

• Keep children and animals away from the work area, small parts could choke if swallowed.

• Parts of the assembly will be easier with 2 people.

• Make sure you have enough space to layout the parts before starting.

• Do not stand or put weight on the product, this could cause damage.

• Assemble the item as close to its final position (in the same room) as possible.

• Assemble on a soft level surface to avoid damaging the unit or your floor (use opened out unit carton).

1

Care and maintenance

• Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners.

• From time to time check that there are no loose screws on this unit.

• This product should not be discarded with household waste. Take to your local authority waste disposal centre.

Note: If required the next page can be cut out and used as reference throughout the assembly. Keep this page with these instructions for future reference.

Tools required

Rule Scissors Hammer

Eye protection (when using a hammer or drill)

Cross-head screwdriver

Electric drill

• We do not recommend the use of power drill/drivers for

inserting screws, as this could damage the unit. Only use hand screwdrivers.

• Safety note: It is recommended that this unit is secured to a wall using the brackets supplied.

• Dispose of all packaging carefully and responsibly.

Components - Panels

Please check you have all the panels listed below

2

1

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

5

2

6

4

3

Left Side (DPF068A)

(720 x 560mm)

Right Side (DPF069A)

(720 x 560mm)

Back (DPF077A)

(479 x 680mm)

Loose Shelf (DPF075A)

(468 x 431mm)

Base (DPF074A)

(469 x 494mm)

Cross Rail (DPF076A)

(469 x 96mm) x 2

7

Door (DPF147B)

(497 x 716mm)

The front surface

of this door is

protected with a

peel-off film

Please check you have all the fittings listed below

3

Components - Fittings

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.

A

Wooden dowel (F22) x 10

B

Metal dowel (F901) x 8

C

D

Large locking nut (F900) x 8

F

G H I a

I c

I d

I e

I b

Ruler - Use this ruler to help correctly identify the screws

mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170

J K

13mm Screw (F63) x 4

E

13mm Screw (F79) x 6

Connecting Sleeve (F432) x 2 19mm Connecting bolt (F461) x 2

L M

25mm Screw (F50) x 5

N

Hinge Cover (F119) x 2

Bracket (F945) x 4

Shelf support (F110) x 4

Hinge Plate (F117) x 2

Hinge Arm (F118) x 2

Leg Bracket (F127) x 2

Leg Socket (F120) x 4

Leg Clip (F128) x 2

16mm Screw (F129) x 16

Leg (F122) x 4

h

ygen

a

OOa

b

25mm Screw (F132) x 2

Handle (F214) x 1

Assembly Instructions

4

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Step 1

Choose which way you would like the door to open

You can fit the door to the left side or right side.

If you would

like your door

to open this

way, fit the

hinge plates

to the left side

If you would

like your door

to open this

way, fit the

hinge plates to

the right side

Step 2

L

Prepare the left side

Refer to step 1 and, if required, fit 2 hinge

plates onto the left side , making sure that the slot is facing towards the front edge.

Screw 4 metal dowels into the holes shown on the left side .

Note: Tighten metal dowels up fully against the panels.

Fit a bracket flush to the top edge of the left side , about 150mm in from the groove, see diagram.

Secure the bracket using screw .

Fit another bracket flush to the back edge of the left side , about 5mm down from the top edge, see diagram.

Secure the bracket using screw .

Note: The brackets must be flush with the top/back edge of the panel.

1

B

1

J

1

J

1

E

J

E

B

L

5mm

150mm

J

E

1

B

1

L

J

E

5mm

150mm

5

Step 3

A

Assembly Instructions

Step 4

L

Prepare the right side

Refer to step 1 and, if required, fit 2 hinge

plates onto the right side , making sure that the slot is facing towards the front edge.

Screw 4 metal dowels into the holes shown on the right side .

Fit a bracket flush to the top edge of the right side , about 150mm in from the groove, see diagram.

Secure the bracket using screw .

Fit another bracket flush to the back edge of the right side , about 5mm down from the top edge, see diagram.

Secure the bracket using screw .

2

B

2

J

2

J

2

E

J

E

Prepare the base

Insert 4 large locking nuts into the base as shown.

Note: Arrow on locking nut must point towards hole in edge of panel.

Tap 6 wooden dowels into the base as shown.

Note: Wooden dowels must not stick out from the edge by more than 10mm or they may damage other panels.

C

3

10mm

A

3

A

C

3

L

2

J

E

B

L

2

L

J

E

Assembly Instructions

6

Step 5

Step 6

Step 7

4

A

C

Prepare the 2 cross rails

Insert 2 large locking nuts into the cross rails as shown.

Tap 2 wooden dowels into the cross rails as shown.

4

A

Finished

front edge

Join the right side and base

Push the base onto the right side .

Use a screwdriver to tighten the 2 large locking nuts fitted to the base .

Note: Turn the large locking nuts as far as they will go - more than 1/2 a turn.

B

C

2

3

2

C

I aI a

I b

b: c: d:

I a

3

Fit the legs to the base

a: Push the leg sockets

. into the holes in the base as shown.

b: Secure each leg

socket with 3 screws .

c: Tap in the centre plug

on each leg socket .

d: Push the leg into

the leg socket .

I a

I e

3

x 3

I a

I b

x 2

Assembly Instructions

7

Step 8

Step 9

Fit the left side

Push the left side onto the assembly.

Use a screwdriver to tighten the large locking nut fitted to the 2 cross rails and the 2 fitted to the base .

Note: Turn the large locking nuts as far as they will go - more than 1/2 a turn.

3

1

C

4

2

Fit the 2 cross rails

Push each cross rail onto the right side .

Use a screwdriver to tighten the large locking nut fitted to each cross rail .

Note: Turn the large locking nuts as far as they will go - more than 1/2 a turn.

4

2

C

4

Support this cross rail until the left side has been fitted in the next step.

2

4

1

4

3

Assembly Instructions

8

Step 10

Step 11

Secure the back

The bottom edge of the back must be flush with the bottom edge of the base .

Secure the back to the back edge of the base using 3 screws . .

Stand the unit up for the next stage.

6

3

F

Fit the back

Slide the back along the grooves in the side panels and .

6

1 2

6

2

4

3

2

4

1

3

6

F

1

Assembly Instructions

9

Step 12

Secure the unit to the wall

Using the brackets fitted to the back edge of the sides and screw the unit to the wall.

Fixings are not supplied as they will need to suit the wall type, and the length of screw will depend on the distance of the back of the unit to the wall.

J

5mm

Warning: Take care when

drilling the wall

that you do not drill into any pipes, wires etc. If in doubt, consult an expert.

Step 13

Joining units together

Fittings have been supplied so you are able to join units together.

Make sure that your first unit is level.

Push the other unit up against first unit and ensure both units are level.

Check that the ends are flush and in line, then clamp them together.

Using a 5mm drill bit, drill 2 holes (approximate positions shown circled) in the side panel into the adjoining side panel of the other unit.

Push the connecting sleeves into the holes and then screw the connecting bolts in from the other side.

G

H

G

H

1

2

1 2

Assembly Instructions

10

Step 14

Fit the loose shelf

Insert 4 shelf studs at the required height.

Lower the loose shelf down onto the shelf studs .

Step 16

K

5

Prepare the door

Push fit the 2 hinges into the door .

Secure each hinge with 2 screws .

Note: Before securing with the screws, make sure that the hinges are positioned at 90 degrees with the front edge of the door.

Step 15

Fit the unit to worktop

To fit the unit to the worktop use 2 screws to screw up through the holes in the cross rail as shown.

Then use 2 screws to screw up through the brackets as shown.

D

M

7

F

E

J

4

7

M

90

M

D

1

2

K

x 4

5

F

E

4

Assembly Instructions

11

Step 17

Small piece of

waste wood

Drill these 2 holes if

you have fitted the

hinges to the left side.

Drill these 2 holes if you

have fitted the hinges

to the right side.

DO NOT drill

any other holes

DO NOT drill

any other holes

or

Drill the handle holes in the door

Important: Please follow these instructions carefully.

Lay the door down onto a smooth surface.

Important: Carefully choose which holes you need to drill. This will depend on which side you fitted the hinge plates .

Check that the holes and hinges are in the same place as the diagrams.

Note: We recommend the use of a small piece of waste wood, placed behind the hole while drilling, to reduce the possibility of any breakout.

Using the pilot hole in the rear face of the door, . drill through the holes indicated opposite, using a 2.5mm diameter drill.

Turn the door over and open out the 2.5mm holes that you have just drilled by drilling back through them with a 5mm drill.

Note: Drill bits are not provided.

7

L

7

ONLY drill

these 2 holes

ONLY drill

these 2 holes

Small piece of

waste wood

7

PLEASE FOLLOW THESE INSTRUCTIONS CAREFULLY

TO CHOOSE WHICH 2 HOLES YOU WILL NEED TO DRILL

O a

Assembly Instructions

12

Step 18

a:

b:

c:

This shows the door being fitted to hinge

plates on the right side.

You may have fitted them to the left side.

Push and

click

Push

d:

Fit door and handle

2 people are needed here

Note: The easiest way to

attach the door is to fit the top hinge first, then align and fit the other hinge.

a: Push the hooks on

the hinge arm underneath the front of the hinge plate .

b: Press the front of the

hinge arm against the hinge plate until it clicks into place.

c: If you need to

seperate the hinge arm . from the hinge plate, . press the button at the end of the hinge arm and lift it off of the hinge plate.

d: Attach the handle

. to the door using the 2 screws packed with it.

L

M

L

M

L

M

L

M

7

M

L

M

O a

O b

7

b

7

O b

Assembly Instructions

13

Step 19

Adjust the door if needed

a: Height adjustment.

Loosen screws A on hinge plates and move door up or down as required. Retighten screw A.

b: Forward and Back

adjustment. Loosen screw B on hinge arm and move door in or out as required. Retighten screw B.

c: Sideways

adjustment. To move door ‘out’ loosen screw C. To move door ‘in’ tighten screw C

a:

b:

c:

A

C

B

Assembly Instructions

14

Step 20

Fit the hinge covers

Push the hinge covers onto the hinge arms .

Step 21

N

M

h

ygen

a

N

M

Pencil mark

Plinth

I c

I d

Plinth

I e I e

Fit the plinth

After cutting the plinth to the required length, offer the plinth up to the unit and using a pencil, mark the position of the unit’s legs on the back of the plinth.

Position the leg bracket . so it is in the centre of the pencil mark and half way up the plinth.

Fix the leg bracket to the back of the plinth using 2 screws .

Slide the leg clip into the leg bracket

Offer the plinth up to the unit and push the leg clips onto the legs . .

I b

I c

I d

.

I e

608/2345

608/2369

205/5668

198/9917

608/2352

Black Plinth Pack

Cream Plinth Pack

Oak Plinth Pack

White HN Plinth Pack

White Gloss Plinth Pack

Assembly Instructions

15

If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800

and quote the reference numbers on the component pages.

Argos Ltd, 489-499 Avebury Boulevard, Central Milton Keynes, MK9 2NW

Step 22

ALR2651

Fit other products to the unit

To fit other products to this unit e.g. worktops etc., please follow the instructions packed with them.

We recommend that you consult a qualified joiner or kitchen fitter.

Assembly is complete

Warning: The unit is heavy. Lift with care.

MADE IN

BRITAIN

Assembly Instructions - Please keep for future reference

Dimensions

Width - 100cm

Depth - 59cm

Height - 87cm

Valencia - 1000mm Base Cabinet

If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800

Issue 1 - 16/08/11

Important - Please read these instructions fully before starting assembly

hygena

656/5790

633/2882

633/2710

656/5295

656/4540

633/2806

Cabinet

Black Door Pack

Cream Door Pack

Grey Door Pack

Plum Door Pack

White Door Pack

Safety and Care Advice

Important - Please read these instructions fully before starting assembly

• Warning: This unit weighs approximately 26kgs. Please lift with care.

• Check you have all the components and tools listed on pages 2, 3 and 4.

• Remove all fittings from the plastic bags and separate them into their groups.

• Keep children and animals away from the work area, small parts could choke if swallowed.

• Parts of the assembly will be easier with 2 people.

• Make sure you have enough space to layout the parts before starting.

• Do not stand or put weight on the product, this could cause damage.

• Assemble the item as close to its final position (in the same room) as possible.

• Assemble on a soft level surface to avoid damaging the unit or your floor (use opened out unit carton).

• We do not recommend the use of power drill/drivers for

inserting screws, as this could damage the unit. Only use hand screwdrivers.

• Safety note: If there is any chance of this unit being pulled over by children etc. it is recommended that the unit is secured to a wall using suitable fixings (not supplied).

• Dispose of all packaging carefully and responsibly.

1

Care and maintenance

• Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners.

• From time to time check that there are no loose screws on this unit.

• This product should not be discarded with household waste. Take to your local authority waste disposal centre.

Note: If required the next page can be cut out and used as reference throughout the assembly. Keep this page with these instructions for future reference.

Tools required

Rule Scissors Hammer

Eye protection (when using a hammer or drill)

Cross-head screwdriver

Electric drill

Components - Panels

Please check you have all the panels listed below

2

1

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

5

2

6

4

3

Left Side (DPF068A)

(720 x 560mm)

Right Side (DPF069A)

(720 x 560mm)

Loose Shelf (DPF083A)

(968 x 431mm)

Base (DPF082A)

(969 x 494mm)

Back (DPF085A)

(979 x 680mm)

8

Cross Rail (DPF084A)

(969 x 96mm) x 2

Muntin Rail (DPF086A)

(36 x 688mm)

7

Valencia Door (DPF147B)

(497 x 716mm) x 2

The front surface

of this door is

protected with a

peel-off film

Please check you have all the fittings listed below

3

Components - Fittings

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.

A

Wooden dowel (F22) x 12

B

Metal dowel (F901) x 8

C

D

Large locking nut (F900) x 8

F

G H I a

I c

I d

I e

I b

Ruler - Use this ruler to help correctly identify the screws

mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170

J K

13mm Screw (F63) x 8

E

13mm Screw (F79) x 6

Connecting Sleeve (F432) x 2 19mm Connecting bolt (F461) x 2

L M

25mm Screw (F50) x 6

N

Hinge Cover (F119) x 4

Bracket (F945) x 4

Shelf support (F110) x 6

Hinge Plate (F117) x 4

Hinge Arm (F118) x 4

Leg Bracket (F127) x 3

Leg Socket (F120) x 5

Leg Clip (F128) x 3

16mm Screw (F129) x 21

Leg (F122) x 5

h

ygen

a

O

40mm Screw (F910) x 2

PPa

b

25mm Screw (F132) x 4

Handle (F214) x 2

Assembly Instructions

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Step 1

B

L

J

E

1

L

J

E

5mm

150mm

Only screw ONE metal dowel into

one of these holes.

1st 5mm hole

2nd 5mm hole

B

1

Prepare the left side

Fit 2 hinge plates onto the left side , orientated as shown.

Screw 3 metal dowels into the holes shown on the left side .

Fit a bracket flush to the top edge of the left side , about 150mm in from the groove, see diagram.

Secure the bracket using screw .

Fit another bracket flush to the back edge of the left side , about 5mm down from the top edge, see diagram.

Secure the bracket using screw .

Note: The brackets must be flush with the top/back edge of the panel.

B

1

J

1

J

1

E

J

E

Step 2

Prepare the left side

Screw a metal dowel into one of the holes shown on the left side . .

Note: Tighten metal dowels up fully against the panels.

B

1

B

4

L

1

If you ARE fitting a sink unit we recommend that you use the 2nd 5mm hole.

If you ARE NOT fitting a sink unit we recommend that you use the 1st 5mm hole.

Assembly Instructions

5

Step 3

Prepare the right side

Screw a metal dowel into one of the holes shown on the right side . .

Use the same hole that you used for the left side in step 1.

L

Prepare the right side

Fit 2 hinge plates onto the right side , orientated as shown.

Screw 3 metal dowels into the holes shown on the right side .

Fit a bracket flush to the top edge of the right side , about 150mm in from the groove, see diagram.

Secure the bracket using screw .

Fit another bracket flush to the back edge of the right side , about 5mm down from the top edge, see diagram.

Secure the bracket using screw .

2

B

2

J

2

J

2

E

J

E

Step 4

J

E

J

E

L

B

J

2

Only screw ONE metal dowel

into one of these holes (use

the same hole that you used

for the left side in step 1).

B

2

Assembly Instructions

6

Step 5

Step 6

I a I a

I b

b:

a:

c: d:

Fit the legs to the base

a: Push the leg sockets

. into the holes in the base as shown.

b: Secure each leg

socket with 3 screws .

c: Tap in the centre plug

on each leg socket .

d: Push the leg into

the leg socket .

I a

I e

3

x 3

I a

I b

I a

3

Prepare the base

Insert 4 large locking nuts into the base as shown.

Note: Arrow on locking nut must point towards hole in edge of panel.

Tap 6 wooden dowels into the base as shown.

Note: Wooden dowels must not stick out from the edge by more than 10mm or they may damage other panels.

C

3

10mm

A

3

A

C

A

C

I a

A

Assembly Instructions

7

Step 7

Step 8

Finished

front edge

C

Prepare the 2 cross rails

Insert 2 large locking nuts into the cross rails as shown.

Tap 2 wooden dowels into the cross rails as shown.

Step 9

4

A

Join the right side and base

Push the base onto the right side .

Use a screwdriver to tighten the 2 large locking nuts fitted to the base .

Note: Turn the large locking nuts as far as they will go - more than 1/2 a turn.

B

F

3

2

C

2

3

2

A

4

Fit a cross rail

Push a cross rail onto the right side as shown.

Use a screwdriver to tighten the large locking nut fitted to the cross rail .

Note: Turn the large locking nuts as far as they will go - more than 1/2 a turn.

2

C

4

C

4

O

Assembly Instructions

8

Step 10

Step 11

Prepare the muntin rail

Tap 2 wooden dowels into the muntin rail as shown.

3

4

A

8

Fit the muntin rail

Attach the muntin rail to the base and cross rail and secure with 2 screws .

O

8

3

4

O

Step 12

3

4

Support this cross rail until the left side has been fitted in the next step.

4

Fit a cross rail

Push a cross rail onto the right side as shown.

Use a screwdriver to tighten the large locking nut fitted to the cross rail .

Note: Turn the large locking nuts as far as they will go - more than 1/2 a turn.

2

C

4

2

If you are fitting a sink unit you will need to fit this support rail here (refer back to step 3).

Assembly Instructions

9

Step 13

Step 14

2

3

Fit the left side

Push the left side onto the assembly.

Use a screwdriver to tighten the large locking nut fitted to the 2 cross rails and the 2 fitted to the base .

Note: Turn the large locking nuts as far as they will go - more than 1/2 a turn.

3

1

C

4

1

2

1

Fit the back

Slide the back along the grooves in the side panels and .

6

1 2

Assembly Instructions

10

Step 15

Step 16

Secure the back

The bottom edge of the back must be flush with the bottom edge of the base .

Secure the back to the back edge of the base using 4 screws . .

Stand the unit up for the next stage.

6

3

F

6

3

Secure the unit to the wall

Using the brackets fitted to the back edge of the sides and screw the unit to the wall.

Fixings are not supplied as they will need to suit the wall type, and the length of screw will depend on the distance of the back of the Unit to the wall.

F

Warning: Take care when drilling the wall that you do not drill into any pipes, wires etc. If in doubt, consult an expert.

1 2

1

2

Assembly Instructions

11

Step 17

Joining units together

Fittings have been supplied so you are able to join units together.

Make sure that your first unit is level.

Push the other unit up against first unit and ensure both units are level.

Check that the ends are flush and in line, then clamp them together.

Using a 5mm drill bit, drill 2 holes (approximate positions shown circled) in the side panel into the adjoining side panel of the other unit.

Push the connecting sleeves into the holes and then screw the connecting bolts in from the other side.

G

H

5mm

G

H

Fit the loose shelf

Insert 6 shelf studs at the required height. 2 in each side and , 1 in the back and 1 in the munting .

Lower the loose shelf down onto the shelf studs .

K

5

K

x 2

K

x 2

K

x 2

Step 18

5

1

6

8

2

1

2

6

8

Assembly Instructions

12

Step 19

Fit the unit to worktop

To fit the unit to the worktop use 2 screws to screw up through the holes in the cross rail as shown.

Then use 2 screws to screw up through the brackets as shown.

F

E

J

4

F

E

Step 20

Prepare the doors

Push fit 2 hinges into each door .

Secure each hinge with 2 screws .

Note: Before securing with the screws, make sure that the hinges are positioned at 90 degrees with the front edge of the door.

D

M

7

M

90

M

D

4

Assembly Instructions

13

Step 21

Small piece of

waste wood

DO NOT drill

any other holes

DO NOT drill

any other holes

ONLY drill

these 2 holes

ONLY drill

these 2 holes

Small piece of

waste wood

7

This will be

the left door

This will be

the right door

Drill the handle holes in the doors

Important: Please follow these instructions carefully.

Lay the doors down onto a smooth surface.

Important: Carefully choose which holes you need to drill.

Check that the holes and hinges are in the same place as the diagrams.

Note: We recommend the use of a small piece of waste wood, placed behind the hole while drilling, to reduce the possibility of any breakout.

Using the pilot hole in the rear face of the door . , drill through the holes indicated opposite, using a 2.5mm diameter drill.

Turn the door over and open out the 2.5mm holes that you have just drilled by drilling back through them with a 5mm drill.

Note: Drill bits are not provided.

7

PLEASE FOLLOW THESE INSTRUCTIONS CAREFULLY

TO CHOOSE WHICH 2 HOLES YOU WILL NEED TO DRILL