Hygena 249-4834 Instruction manual

Bergen 180

Assembly Instructions- Please keep for future reference

DR825062

249/4834

248/6921

226/8730

Cabinet

248/7937

247/1651

Doors foil/foil

248/3591

248/8015

Doors foil/mirror

249/6265

Mirror doors

Dimensions

Tip : To prevent damage,

we recommend that you

build your unit on the

carton(s) it was packed in.

Width - 180cm

Depth - 59.5cm

Height - 199.8cm

249/4834 OAK 248/6921 WAL 226/8730 WHT 248/7937 OAK doors 247/1651 WAL doors 248/8015 WAL FOIL MIRROR 248/3591 OAK FOIL MIRROR 249/6265 MIRROR

Important – Please read these instructions fully before starting assembly

If you need help or have damaged or missing parts, please visit: www.argos-support.co.uk or email: Help@ClickSpares.co.uk (quoting your original order number) Alternatively, call the Spares Helpline on: 0370 112 1928 For any other queries please contact the Customer Helpline on: 0345 640 2020

Issue 1 - 03/06/15

Safety and Care Advice

Important – Please read these instructions fully before starting assembly

• Check you have all the components and tools listed on pages 2 and 3.

• Remove all fittings from the plastic bags and separate them into their groups.

• Keep children and animals away from the work area, small parts could choke if swallowed.

• Make sure you have enough space to layout the parts before starting.

Care and maintenance

• Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners.

• Do not stand or put weight on the product, this could cause damage.

• Assemble the item as close to its final position (in the same

room) as possible.

• Assemble on a soft level surface to avoid damaging the unit or your floor.

• Parts of the assembly will be easier with 2 people.

• From time to time check that there are no loose screws on this unit.

•To reduce the likelihood of damaging your product please ensure that your

power drill is set on a low torque setting.

• Dispose of all packaging carefully and responsibly.

• This product should not be discarded with household waste. Take to your local authority waste disposal centre.

Handy Hints

• Assemble all parts and bolts loosely during assembly, only once the product is complete should you fully tighten the bolts

• Regularly check and ensure

tightend properly.

Note: if required the next page can be cut out and used as reference throughout the assembly. Keep this page with these instructions for future reference.

2

Components - Panels

For damaged or missing parts, please visit: www.argos-support.co.uk or email: Help@ClickSpares.co.uk

Please check you have all the panels listed below

Cabinet

Left side

1

(199.8 x 52.9cm)

P2883

Top

5

(177 x 51cm)

P1896

Plinth x2

7

(177 x 6cm)

P7241

Right side

2

(199.8 x 55.8cm)

P2882

Upright

3

(190.3 x 49cm)

P2886

Bottom

6

(177 x 51.1cm)

P1897

8

Shelf x2

(87.7 x 48.8cm)

P1898

Foldy back x2

4

(193 x 89cm)

BO3431

3

Plug, Nylon x 32 (5x9mm)

E

FK1082

Connecting plate x 8

O

FK1236

Brush x 3 (1951mm)

T

PM1652C

Door trim x 1 (1951mm)

U

PM1652D

Door handle x 3 (1951mm)

S

PM1652B

Not used until door assembly

Not used until door asse- mbly

Not used until door assembly

Components - Fittings

For damaged or missing parts, please visit: www.argos-support.co.uk or email: Help@ClickSpares.co.uk

Please check you have all the fittings listed below

Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.

1/2

A

FK1005

Confirmat screw x 4 (5x40mm)

D

FK1309

Screw x 4 (4x12.5mm)

G

FK1052

Double locking screw x 3 (5x66.5mm)

J

FK1248

Corner connector, white x 2

M

FK1235

L-Bracket x 1

P

PM1828

B

Locking screw x 18

(5x24mm)

H

Wood dowel x 4 (8x30mm)

K

Hanger rail support, gray x 4

N

Nail holder x 1

Q

FK1011

C

Screw x 11 (4x15mm)

F

Nail x 60

FK1411

I

Large locking nut x 24 (15x12mm)

FK1217

L

Peg, brown x 1

FK1419

PM1611

R

FK1400

FK1515

FK1012

15mm

FK1234

PK1611

Hanger rail x 2

V

(869mm)

Guide rail x 1, metal (1769mm)

FK1013

W

Guide rail x 1, plastic(1769mm)

ZF99936

OR

Allen key x 1 (3mm)

Wall plug (6mm) and parkerscrew x 1

4

Screw x 33 (4x15mm)

AC

ZF9997L

Front guide part x 2

AI

ZF9997C

Spacer x 1

AE

ZF9997F

Sliding door connecting plate x 2

AK

ZF9997B

Sliding door connecting bracket x 2

AL

ZF9997A

Back guide part x 2

AJ

ZF9998D

Components - Fittings

Not used until door assembly

Please check you have all the fittings listed below

Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.

A

2/2

AA

Screw x 2 (3.5x35mm)

AD

Screw x 2 (4x14mm)

AG

End stop x 2

ZF9997I

ZF9997J

ZF9997G

AB

Screw x 9 (3.5x25mm)

AH

Stop guide rail x 2

ZF9997K

ZF9997H

AF

Tapping block for guide rail x 2

ZF9997E

Tools required

Phillips screwdriver

(medium & large)

Flatblade screwdriver

(medium)

Piercer

(small)

5mm Suitable drill bit

Ruler - Use this ruler to help correctly identify the screws

0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100

Drill

Spirit level

Setsquare

105

Small

Stairs

0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150

0 1 2 3 4 5 6

hammer

Ruler/tape measure

Scissors

Eye protection (when using a hammer or drill)

110 115 120 125 130 135 140 145 150 155 160 165 170

5

Assembly Instructions

BBBBBBBBBBBBBBBBBBB

K

Step 1

a:

Cabinet assembly

a: Screw 9 locking screws

B

into the holes on back

of the left side 1.

AB

D

Mount hanger rail support K, fasten with 1 screw D. Screw D into the board between two predrilled holes. Mount tapping block for guide rail f with two screws b.

b: Screw 9 locking screws

B into the holes on back of the right side 2 .

Mount hanger rail support K, fasten with 1 screw D. Screw D into the board between two predrilled holes.

Mount tapping block for guide rail f with two screws b.

AF

b:

AB

AF

AB

K

Finished front edge

D

K

AF

AB

1

AB

Finished front edge

2

C: Mount hanger rail

support K on the upright 3, fasten with screw D 1x. Screw D into the board between two predrilled holes

Turn over.

Mount hanger rail support K on the upright 3, fasten with screw D 1x. Screw D into the board between two predrilled holes.

6

c:

D

K

3

Finished front edge

Assembly Instructions

568

7

IIIIIIIIIIIIIIIIIIH

H

Step 1

Cabinet assembly

d: Insert 6x small locking

nuts I into the top 5.

Make sure the ‘arrow’ on I is pointing towards the hole in the edge of the top

5.

e: Insert 6x small locking

nuts I into the bottom 6.

Make sure the ‘arrow’ on I is pointing towards the hole in the edge of the bottom 6.

d:

Finished front edge

e:

plain chipboard

Finished front edge

f: Insert 6x small locking

nuts I into the shelf 6.

2x.

Make sure the ‘arrow’ on I is pointing towards the hole in the edge of the bottom 6.

g: Insert 4x wooden

dowels J into the plinth

7. 2x.

f:

g:

2x

Finished front edge

2x

Finished front edge

7

Assembly Instructions

VGG

G

6318855

365

AAA

388

6

Step 1

Cabinet assembly

h: Attach top 5 with 2x

confirmat screws A to the upright 3. Use allenkey V.

Attach bottom 6 with 2x confirmat srews A to the

upright 3

.

i: Attach 2x the shelf 8 to

the upright 3 with 3x double locking screws G.

Use a screwdriver to turn 6x locking nuts clockwise to lock.

Finished front edge

h:

Plain chipboard

i:

j: Attach the left side 1

with 9x double locking screws G on the top 5, shelf 8 and the bottom

6.

Use a screwdriver to turn 9x locking nuts clockwise to lock.

Finished front edge

Plain chipboard

j:

Plain chipboard

8

Assembly Instructions

JJCCFFF

JCC

76776282544N6

2

F

C

N

F

Step 1

Cabinet assembly

k:Attach 2x the plinth 7

between the left site 1 and the right side 2. Note: that the finished side

is properly placed.

Attach the right side 2 with 9x double locking screws G on the top 5, shelf 8 and the bottom 6.

k:

Use a screwdriver to turn 9x locking nuts clockwise to lock.

Mount corner connector J with 2 screws C on the plinth 7 and bottom 6.

l: Attach 2x foldy back 4

to back of cabinet with the coloured surface facing the inside of the cabinet using 60x nails F and 26x screws C.

Use nail holder N to hold the nails F vertical and at correct distance as you secure the 2x foldy back

4. Nails F should be spaced about 150mm apart.

Finished front edge

Finished side

l:

Important:

Cabinet MUST be ‘square’ when

Finished front edge

back is attached.

Stand up the unit! 2 people required to stand up unit.

9

Assembly Instructions

AD

P

AG

M

CCCCCCCCQ

AHAHABABABABABAAAA

R

88123

123

6

5

AD

Q

AD

AG

Q

P

K

AB

AA

R

6

7

AH

R

Step 1

Cabinet assembly

m: Position L-Bracket M

onto top 5 , by using 1x screw C.

Position metal guide rail Q onto top 5 , fix with 7x screws C.

Attach 2x end stop g on the end of the guide rail Q with 2x screws d.

Place 2x hanger rail P into hanger rail support K.

A

x2

B

x7

C

x7

C

m:

n:Position plastic guide

rail R onto bottom 6 , fix with 9x screws b.

Attach 2x stop guide rail h on the end of the guide rail R, mount with 2x screws a.

A

C

x x

. . . . . . .

n:

B

x10

D

10

x9

Assembly Instructions

MMW

L

Step 1

Place cabinet

o: Use to 1x wall plug W

to mount L-Bracket M on the wall, please see last page for more information.

o:

p: Before adjusting the

doors, use a spirit level to check if the base of this unitis level front-to-back and side-to-side in the three positions shown.

Use pegs L to square your unit. Knock peg L in, as far as you require, under the ends of the unit and then snap off flush with the panel.

p:

SNAP!

11

A Guide to - Wall Mounting & Fixings

Important note:

If plastic wall plugs are supplied with your product:

- these are only suitable for use in masonry walls.

If you are in any doubt about the correct wall plugs for your wall, seek professional advice.

Failure of the product due to using incorrect fixings is the responsibility of the installer.

Important: When drilling into walls always

check that there are no hidden wires or pipes etc.

Make sure that the screws and wall plugs being used are suitable for supporting your unit. Consult a qualiﬁed tradesperson if you are unsure.

Hints:

1: General rule: Always use a larger screw and wall plug

if you are not sure.

2: Ensure you use the recommended drill bit to match the wall

plug and hole size.

3: Ensure you drill the hole horizontally, do not force the drill or

enlarge the hole.

4: Take extra care when drilling high walls, ceilings and ceramic

tiles. Ensure wall plugs are inserted beyond the thickness of the ceramic tiles to avoid the tiles splitting or cracking.

5: Ensure wall plugs are well fitted and are a tight fit in the

drilled hole.

Types of walls

No.1 “General Purpose” wall plug

Generally aerated blocks should not be used to support heavy loads, use a specialist fitting in this case. For light loads, general purpose wall plugs can be used.

No.2 “Plasterboard” wall plug

You can use one of the following types of wall plug if your walls are made of brick, breeze block, concrete, stone or wood.

No.3 “Cavity Fixing” wall plug

For use with plasterboard partitions or hollow wooden doors.

No.4 “Cavity Fixing-Heavy Duty”

wall plug

No.5 “Hammer Fixing” wall plug

For use with walls stuck with plasterboard. The hamemr fixing allows it to be fixed to the wall rather than the plasterboard. Always check the fixing is secure to the retaining wall.is secure to the retaining wall.

No.6 “Shield Anchor” wall plug

Heavy loads

For use when attaching light loads on to plasterboard partitions.

Care & Maintenance

For use when fitting or supporting heavy loads such as shelving, wall cabinets and coat racks.

Safety: Always check the ﬁtting and location to ensure your safety in and around the home.

For use with heavier loads such as TV & HiFi speakers and satelite dishes etc.

Fitting: From time to time check the ﬁtting to ensure the wall plugs or screws do not become loose.

Bergen 180 Gloss/Mirror doors

12134

3

Assembly Instructions- Please keep for future reference

DR825088

412/7305

417/9463

Gloss/Mirror doors

Dimensions

Width - 180cm

Depth - 6.7cm

Height - 195.2cm

Tip : To prevent damage,

we recommend that you

build your unit on the

carton(s) it was packed in.

412/7305 WHITE GLOSS- MIRROR 417/9463 CASH GLOSS- MIRROR

Dimensions

Important – Please read these instructions fully before starting assembly

If you need help or have damaged or missing parts, please visit: www.argos-support.co.uk or email: Help@ClickSpares.co.uk (quoting your original order number) Alternatively, call the Spares Helpline on: 0370 112 1928 For any other queries please contact the Customer Helpline on: 0345 640 2020

Issue 1 - 03/07/15

Safety and Care Advice

Important – Please read these instructions fully before starting assembly

• Check you have all the components and tools listed on pages 2 and 3.

• Remove all fittings from the plastic bags and separate them into their groups.

• Keep children and animals away from the work area, small parts could choke if swallowed.

• Make sure you have enough space to layout the parts before starting.

Care and maintenance

• Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners.

• Do not stand or put weight on the product, this could cause damage.

• Assemble the item as close to its final position (in the same

room) as possible.

• Assemble on a soft level surface to avoid damaging the unit or your floor.

• Parts of the assembly will be easier with 2 people.

• From time to time check that there are no loose screws on this unit.

•To reduce the likelihood of damaging your product please ensure that your

power drill is set on a low torque setting.

• Dispose of all packaging carefully and responsibly.

• This product should not be discarded with household waste. Take to your local authority waste disposal centre.

Handy Hints

• Assemble all parts and bolts loosely during assembly, only once the product is complete should you fully tighten the bolts

• Regularly check and ensure

tightend properly.

Note: if required the next page can be cut out and used as reference throughout the assembly. Keep this page with these instructions for future reference.

2

Components - Panels

For damaged or missing parts, please visit: www.argos-support.co.uk or email: Help@ClickSpares.co.uk

Please check you have all the panels listed below

Cabinet supplied separately

249/4834

248/6921

226/8730

Segment x2

1

(91.5 x 65cm)

P3355

Mirror-Segment x2

3

(91.5 x 65cm)

PS3335

132/3384

Segment middle x1

2

(91.5 x 65.1cm)

P3356

Mirror-Segment middle x1

4

(91.5 x 65.1cm)

PS3274

3

For damaged or missing parts, please visit:

Components - Fittings

www.argos-support.co.uk or email: Help@ClickSpares.co.uk

Please check you have all the fittings listed below

Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.

D

Screw x 72 (4x12.5mm)

S

Door handle x 3 (1951mm)

AC

FK1309

PM1652B

ZF9997L

E

Plug, Nylon x 32

T

Brush x 3 (1951mm)

A

(5x9mm)

FK1082

PM1652C

O

Connecting plate x 8

U

Door trim x 1 (1951mm)

AE

Spacer x 1

AI

FK1236

PM1652D

ZF9997F

ZF9997C

Screw x 33 (4x15mm)

ZF9998D

AJ

Back guide part x 2

AK

Sliding door connecting plate x 2

Tools required

Phillips screwdriver

(medium & large)

Drill

Flatblade screwdriver

(medium)

Piercer

(small)

Spirit level

5mm Suitable drill bit

Setsquare

Ruler - Use this ruler to help correctly identify the screws

ZF9997B

Stairs

Front guide part x 2

AL

ZF9997A

Sliding door connecting bracket x 2

Small hammer

0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150

0 1 2 3 4 5 6

Ruler/tape measure

Scissors

Eye protection (when using a hammer or drill)

0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100

4

105

110 115 120 125 130 135 140 145 150 155 160 165 170

1112112

1

Assembly Instructions

E

UUSDDDDDDDDDDDDDDDDDDDD

D

Step 2

3 Segment slide door left

a: Put 8x nylon plug E

into the segment 1. Use a small hammer. Repeat this step.

a:

2x

b: Mount door trim U with

3x screws D on segment

1.

Note: there should be no gap between doorsegment 1�and door trim U.

c: Mount segment middle

2 with 3x screws D on door trim U. Mount segment 1 with 4x screws D on door trim U.

b:

No Gap between metal profiles and door panel!

c:

d: Mount door handle S

on segment 1 with 4x screws D and on middle segment 2 with 3x screws D.

Note: there should be no gap between doorsegment 1 and door handle S.

d:

5

Assembly Instructions

11211

S

T

AC

AJ

AC

AKAKACACACACACAJAJACACACAC

TOODDDD

SAEOODDD

D

Step 2

3 Segment slide door left

e: Mount 4x connecting

plate O, each with 2x screws D on segment 1 and 2x screws D on middle segment 2.

Remove protective film from door handle S. Stick 1x brush T onto door handle S by partially removing the cover from adhease as brush is applied.

f: Upside.

Mount 2x Sliding door connecting plate k squarely by using the guidemarks in the plate

k, each with 6x screws c on segment 1. Attach

1x spacer e with 1x screw c on the brush side sliding door connecting plate k.

Please remove

the protective film!

e:

f:

g: Underside.

Mount 2x back guide part j , each with 2x screws c on segment 1.

6

g:

x2

121

Assembly Instructions

AJ

RRR

Step 3

Place left slide door

2 People are required for

step 3a and 3b.

Hook the 2x back guide

a:

part j into the plastic guide rail R.

a:

a: Detail.

The hook of the back guide part j should be in the front guide of the plastic guide rail R

7

Assembly Instructions

121

QQQ

Q

AKAKAK

Step 3

Place left slide door

b: Hook Sliding door

connecting platek on metal guide rail Q.

b:

b: Detail.

The wheel of the sliding door connecting plate k should be in the front guide of the metal guide rail Q.

To lock the door, lock the Sliding door connecting plate k on the guide rail Q with the locking pawl.

push the yellow lock pin to secure part

k to rail

8

Assembly Instructions

1121112

1

E

SSSDDDDDDDDDDDDDDDDDDDDDD

3433333

4

Step 4

3 Segment slide door right

a: Put 8x nylon plug E

into the segment 3. Use a small hammer. Repeat this step.

b: Mount door handle S

with 4x screws D on

with 4x screws D on segment 1 .

segment 3 .

Note: there should be no

gap between doorsegment

1 and door handle S.

3 and door handle S.

(see �).

a:

2x

b:

c: Mount segment middle

2 with 3x screws D on

4 with 3x screws D on

door handle S.

door handle S. Mount segment 1 with

Mount segment 3 with 4x screws D on door

4x screws D on door handle S.

handle S.

d: Mount door handle S

on segment 1 with 4x

on segment 3 with 4x screws D and on middle

screws D and on middle segment 2 with

segment 4 with 3x screws D.

3x screws D.

No Gap between metal profiles and door panel!

c:

d:

Note: there should be no

gap between doorsegment

1 and door handle S.

3 and door handle S.

(see �).

9

Assembly Instructions

11211

TOODDDDSO

O

D

T

S

T

ACACACACACACAC

AC

ALALAI

AIx2AC

AI

34333

Step 4

3 Segment slide door right

e: Mount 4x connecting

plate O, each with 2x screws D on segment 3 and 2x screws D on middle segment 4.

e:

Remove protective film from door handle S. Stick 2x brush T onto 2x door handle Sby partially remove the cover from adhease as brush is applied.

f: Upside.

Mount 2x sliding door connecting bracket l squarely by using the guidemarks in the plate

l, each with 6x screws c on segment 3.

Please remove

the protective film!

f:

g: Underside.

Mount 2x front guide

Mount 2x front guide part i , each with 2x

part i , each with 2x screws c on

screws c on segment 1.

segment 3

10

g:

Assembly Instructions

R

RAIR

343

Step 5

Place right slide door

a: Hook the 2x front guide

part i into the plastic guide rail R.

a:

a: Detail.

The hook of the front guide part i should be in the rear guide of the plastic guide rail R

11

Assembly Instructions

QQQ

Q

ALALAL

343

Step 5

Place right slide door

b: Hook the sliding door

connecting bracketl on metal guide rail Q.

a:

b: Detail.

The wheel of the sliding door connecting bracket l should be in the rear guide of the metal guide rail Q.

To lock the door, lock the sliding door connecting bracket l on the guide rail Q with the locking pawl.

12

Hygena 249-4834 Instruction manual

Specifications and Main Features

Frequently Asked Questions

User Manual