Hygena 241-8535 Instruction manual

Bergen 150 Mirror/mirror

Assembly Instructions- Please keep for future reference 241/8535

DR8250570

Dimensions

Tip : To prevent damage,

Width - 150cm

Depth - 59.5cm

Height - 199.8cm

we recommend that you

build your unit on the

carton(s) it was packed in.

Important – Please read these instructions fully before starting assembly

If you need help or have damaged or missing parts, please visit: www.argos-support.co.uk or email: Help@ClickSpares.co.uk (quoting your original order number) Alternatively, call the Spares Helpline on: 0370 112 1928 For any other queries please contact the Customer Helpline on: 0345 640 2020

Issue 3 - 05/11/15

Safety and Care Advice

Important – Please read these instructions fully before starting assembly

• Check you have all the components and tools listed on pages 2 and 3.

• Remove all fittings from the plastic bags and separate them into their groups.

• Keep children and animals away from the work area, small parts could choke if swallowed.

• Make sure you have enough space to layout the parts before starting.

Care and maintenance

• Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners.

• Do not stand or put weight on the product, this could cause damage.

• Assemble the item as close to its final position (in the same

room) as possible.

• Assemble on a soft level surface to avoid damaging the unit or your floor.

• Parts of the assembly will be easier with 2 people.

• From time to time check that there are no loose screws on this unit.

•To reduce the likelihood of damaging your product please ensure that your

power drill is set on a low torque setting.

• Dispose of all packaging carefully and responsibly.

• This product should not be discarded with household waste. Take to your local authority waste disposal centre.

Handy Hints

• Assemble all parts and bolts loosely during assembly, only once the product is complete should you fully tighten the bolts

Instruction video

• This manual is provided with an additional instruction video. If the icon on the right is displayed at a particular step in the manual, Follow the link: http://nlink.nu/vid02 Or scan the QR code on the left with your phone.

• Regularly check and ensure

tightend properly.

See page 2 for link to instruction video!

Note: if required the next page can be cut out and used as reference throughout the assembly. Keep this page with these instructions for future reference.

Components - Panels

For damaged or missing parts, please visit: www.argos-support.co.uk or email: Help@ClickSpares.co.uk

Please check you have all the panels listed below

Left side

(199.8 x 52.9cm)

P2883

Top

(146.9 x 51cm)

P1889

Plinth x2

(146.9 x 6cm)

P7242

Right side

(199.8 x 55.8cm)

P2882

Upright

(190.3 x 49cm)

P2886

Bottom

(146.9 x 51.1cm)

P1891

Shelf x2

(72.7 x 48.8cm)

P1893

Foldy back x2

(193 x 74cm)

BO3430

Door2x

(195.2 x 76.5cm)

PS3333

Components - Fittings

For damaged or missing parts, please visit: www.argos-support.co.uk or email: Help@ClickSpares.co.uk

Please check you have all the fittings listed below

Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.

1/2

FK1005

Confirmat screw x 4 (5x40mm)

FK1309

Screw x 14 (4x12.5mm)

FK1052

Double locking screw x 3 (5x66.5mm)

FK1248

Corner connector, white x 2

FK1235

L-Bracket x 1

PM1824

Locking screw x 24

(5x24mm)

Plug, Nylon x 16 (5x9mm)

Wood dowel x 4 (8x30mm)

Hanger rail support, gray x 4

Nail holder x 1

FK1011

Screw x 50 (4x15mm)

FK1082

Nail x 60

FK1411

Large locking nut x 18 (15x12mm)

FK1217

Peg, brown x 1

FK1419

Connecting plate x 0

PM1612

FK1400

FK1515

FK1012

15mm

FK1234

FK1236

PK1612

Hanger rail x 2

(719mm)

Door handle x 3 (1952mm)

Allen key x 1 (3mm)

PM1652B

FK1013

Guide rail x 1, metal (1468mm)

Brush x 3 (1952mm)

PM1652C

ZF99936

Wall plug (6mm) and parkerscrew x 1

Guide rail x 1, plastic(1468mm)

Door trim x 1 (1952mm)

PM1652D

Components - Fittings

Please check you have all the fittings listed below

Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.

2/2

Screw x 2 (3.5x35mm)

Screw x 2 (4x14mm)

End stop x 2

Back guide part x 2

ZF9997I

ZF9997J

ZF9997G

ZF9998D

Screw x 11 (3.5x25mm)

Spacer x 1

Stop guide rail x 2

Sliding door connecting plate x 2

ZF9997K

ZF9997F

ZF9997H

ZF9997B

Screw x 7

(4x15mm)

ZF9997L

ZF9997E

Tapping block for guide rail x 2

ZF9997C

Front guide part x 2

ZF9997A

Sliding door connecting bracket x 2

Tools required

Phillips screwdriver

(medium & large)

Stairs

Drill

Flatblade screwdriver

(medium)

Piercer

(small)

Spirit level

5mm Suitable drill bit

Setsquare

Ruler - Use this ruler to help correctly identify the screws

105

0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100

110 115 120 125 130 135 140 145 150 155 160 165 170

0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150

0 1 2 3 4 5 6

Eye protection (when using a hammer or drill)

Small hammer

Ruler/tape measure

Scissors

Assembly Instructions

BBBBBBBBBBBBBBBBBBB

Step 1

Cabinet assembly

a: Screw 9 locking screws

into the holes on back

of the left side 1.

Mount hanger rail support K, fasten with 1 screw D. Screw D into the board between two predrilled holes. Mount tapping block for guide rail f with two screws b.

b: Screw 9 locking screws

B into the holes on back of the right side 2 .

Mount hanger rail support K, fasten with 1 screw D. Screw D into the board between two predrilled holes.

Mount tapping block for guide rail f with two screws b.

Finished front edge

C: Mount hanger rail

support K on the upright 3, fasten with screw D 1x. Screw D into the board between two predrilled holes

Turn over.

Mount hanger rail support K on the upright 3, fasten with screw D 1x. Screw D into the board between two predrilled holes.

Finished front edge

+ 14 hidden pages