Hygena 239-9472 Instruction manual

MADE IN
BRITAIN
Dimensions
Width - 80cm
Depth - 39cm
Height - 101.5cm
Camden - 5 Drawer Mirror Chest
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Issue 1 - 20/06/14
Important - Please read these instructions fully before starting assembly
239/9472
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
Warning: This unit weighs approximately 38kgs. Please lift with care.
• Check you have all the components and tools listed on pages 1, 2 and 3.
• Remove all fittings from the plastic bags and separate them into their groups.
• Keep children and animals away from the work area, small parts could choke if swallowed.
• Make sure you have enough space to layout the parts before starting.
• Do not stand or put weight on the product, this could cause damage.
• Assemble the item as close to its final position (in the same room) as possible.
• Assemble on a soft level surface to avoid damaging the unit or your floor (use opened out unit carton).
1
Care and maintenance
• Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners.
• From time to time check that there are no loose screws on this unit.
• This product should not be discarded with household waste. Take to your local authority waste disposal centre.
Note: If required the next page can be cut out and used as reference throughout the assembly. Keep this page with these instructions for future reference.
Tools required
Rule Scissors Hammer Eye protection
(when using a hammer or drill)
Cross-head screwdriver
Electric drill (only use when drilling into walls)
• We do not recommend the use of power drill/drivers for
inserting screws, as this could damage the unit. Only use hand screwdrivers.
Safety note: It is recommended that this unit is secured to a wall using the bracket supplied.
• Dispose of all packaging carefully and responsibly.
Components - Panels
Please check you have all the panels listed below
2
1 2
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
3
5
4
7
8
9
6
10
Drawer Base (T683-347)
(683 x 347mm) x 5
Drawer Back (W672-124)
(672 x 124mm) x 5
Back (X943)
(932 x 740mm)
Plinth (D1994A)
(722 x 96mm) x 2
Left Side (D1992A)
(979 x 389mm)
Top (D1991A)
(796 x 391mm)
Right Side (D1993A)
(979 x 389mm)
Left Drawer Side (W350-124LH)
(350 x 124mm) x 5
Right Drawer Side (W350-124RH)
(350 x 124mm) x 5
Drawer Front (D2979A)
(716 x 172mm) x 5
(Mirror - SG26 716 x 172mm Safety Back SAR)
Please check you have all the fittings listed below
3
Components - Fittings
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
A
Wooden dowel (F22) x 4
B
Metal dowel (F901) x 14
C
D
Large locking nut (F900) x 4
E
Small locking nut (F3) x 10
F
G
Small metal dowel (F893) x 4
H I
Nail (F51) x 23
N
J K
Hollow core locking nut (F892) x 4
Bracket (F327) x 1
M
Wedgefix (F639) x 20
L
Knock-in Peg (F171) x 20
13mm Screw (F63) x 30
13mm Screw (F79) x 11
O
R Runner (F160) x 5
b
L Runner (F161) x 5
O
c
L Runner (F159) x 5
O
a
R Runner (F162) x 5
O
d
Handle (F330) x 5
9mm Screw (F73) x 30
Assembly Instructions
4
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Step 1
B
Prepare the 5 drawer fronts
Screw 2 metal dowels into the holes shown on the back of each drawer front .
Note: Tighten metal dowels up fully against the panels.
B
5
Prepare drawer sides and drawer backs
Insert a small locking nut into the hole shown on the left drawer side and right drawer side .
Note: The arrow on the locking nut must point towards the hole in the edge of the panel.
F
7
8
Step 2
B
B
B
B
5
x 5
Step 3
Attach the drawer sides to the drawer front
Push the left drawer side . and right drawer side . onto the back of the drawer front .
Turn the small locking nuts on the left drawer side and right drawer side .
Note: Turn the locking nuts clockwise to secure panels - more than 1/2 a turn.
7 8
5
F
7 8
F
5
B
B
F
Groove
x 5
F
x 5 x 5
F
F
7
8
8
7
Warning: Glass! Handle with care
Warning: Glass! Handle with care
Loading...
+ 11 hidden pages